• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.414-417
• /
• 2004

A cone cylinder is used to obtain variable operation conditions for the sonic ejector-diffuser system. The cone cylinder is designed to be shifted upstream and downstream to change the ejector throat area ratio, thus obtaining variable mass flow rates. The present study investigates the effects of ejector throat area ratio and operating pressure ratio on the entrainment of secondary stream for the variable sonic ejector system. The study is carried out experimentally. The ejector throat area is varied at the range from Ψ= 11.88 to 66.69, and the operating pressure ratio is changed from $P_{op}$ / $P_{a}$=1.25 to 9.0. The results show that the variable sonic ejector system can be operated to obtain specific entrainment ratio of secondary stream by altering the ejector throat area ratio and operating pressure ratio.o.

• Journal of ILASS-Korea
• /
• v.27 no.1
• /
• pp.26-35
• /
• 2022

Electrospray is a method of atomizing fluid using high voltage supply and capable of generating continuous flow and coherent size of droplets. Electrical system and properties of fluids has enabled electrospray to have various spray modes. However, its studies have been confined only in Cone jet, which is more stable and easier to manipulate droplets' size than other spraying modes. Therefore, it is necessary to investigate and compare other spraying modes based on experimental parameters and physical properties of fluids. This research paper identified nine different spray modes. It was found out that Sauter Mean Diameter (SMD) is proportional to flow rate of fluids and maximum difference among spray modes was 1.7 times. On the other hand, SMD standard deviation had low variations on specific flow rates of fluids. Pulsed jet mode recorded the largest SMD standard deviation, while Spindle recorded the lowest.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.04a
• /
• pp.600-605
• /
• 2012

In this paper, the acoustic performance of a shipboard large-sized room unit is studied. The room unit is a kind of rectangular absorptive chamber with a partition whose surface absorptive material with fabric skin is attached to. The room unit has one inlet and three outlet. At the inlet, a plane damper is installed to control the flow rate. The acoustic performance of a prototype room unit is measured using a HVAC mock-up. It is shown that its insertion loss is comparable with that of a commercially-used room unit but the developed room unit generates flow noise higher than the other one. The major source of flow noise is analyzed by NADS-R, the noise analysis program for room unit. Cone-shaped dampers are proposed to be used as the damper of a room unit to reduce flow noise. It is shown that the cone-shaped damper decrease flow noise remarkably.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.5
• /
• pp.468-473
• /
• 2012

In this paper, the acoustic performance of a shipboard large-sized room unit is studied. The room unit is a kind of rectangular absorptive chamber with a partition whose surface absorptive material with fabric skin is attached to. The room unit has one inlet and three outlets. At the inlet, a plane damper is installed to control the flow rate. The acoustic performance of a prototype room unit is measured using a HVAC mock-up. It is shown that its insertion loss is comparable with that of a commercially-used room unit but the developed room unit generates flow noise higher than the other one. The major source of flow noise is analyzed by NADS-R, the noise analysis program for room unit. Cone-shaped dampers are proposed to be used as the damper of a room unit to reduce flow noise. It is shown that the cone-shaped damper decrease flow noise remarkably.

• Elastomers and Composites
• /
• v.44 no.4
• /
• pp.423-428
• /
• 2009

The non-Newtonian flow curves of polyurethane melts were obtained by using a Physica cone-plate rheometer at various temperatures. The rheological parameters were obtained by applying non-Newtonian flow equation to the flow curves for polyurethane samples. When the polyurethane samples are under increasing-decreasing shear rate modes, the hysteresis loop and thixotropic behavior were shown. Polyurethane melts behave as strong gels when they are subjected to shear flow, but when the applied stress surpasses the yield stress, they exhibit non-linear viscoelasticity. Upon decreasing shear rate, its shear stress remains smaller than the values measured in the increasing shear rate mode, because of broken of its structure.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2008.04a
• /
• pp.222-227
• /
• 2008

Complex terrain like hill, mountain, and escarpment etc. makes complex air flow. This topographic condition will affect not only speed but also turbulence of wind over the complex terrain. In this paper, turbulence intensities are considered to investigate characteristics of wind over cone-type hills. There are five simple hill models with different slope 0.1${\sim}$0.5(tan${\theta}$) for wind tunnel test. It was observed through wind tunnel tests that turbulence intensities of down-slope wind at the end of the 3-Dimensional hills remarkably increased but ones of windward slope wind at the front side of the hills slightly increased. Also, turbulence intensities proportionally increased with slope of the cone-type hills.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.180-183
• /
• 2004

Superplastic formability depends on flow parameters such as temperature, strain rate, strain and stress, microstructures. Usually, superplastic properties of materials are characterized with using a uni-axial tension testing. However, superplastic sheet is formed under mutiaxial loading condition in most forming practices. In the present study, superplastic characteristics of A15083 alloys were determined with using both a uni-axial and biaxial bulging tests. Specially, cone-type die was used to achieve constant strain rate under constant pressure condition. Even though constant strain rate under a certain pressure was achieved only approximately, a cone-type bulging test was found to be quite beneficial to get a multiaxial formability of superplastic materials.

• Journal of Korean Society of Water and Wastewater
• /
• v.21 no.1
• /
• pp.57-63
• /
• 2007

In this study, the cone type baffle (CTB) was developed to improve the flow distribution in an upflow bioreactor. It was composed of two different zones (anoxic and oxic) by inserting the CTB in the middle of the bioreactor. Based on the results of the dye tracer tests, hydraulic retention time (HRT) for the anoxic, oxic and total volume of the bioreactor was found to be 0.998, 1.996 and 2.994 hr, respectively. And the theoretical HRT for each volume was 1.0, 2.0 and 3.0 hr, respectively. The values of HRT obtained from the tests coincide with theoretical values. Therefore, the flow pattern for each zone inside the bioreactor, which was divided by the CTB, was dominated by complete mix flow rather than plug flow. Based on the results of the transection measurements, the DO concentration for each zone inside the bioreactor was clearly distinguished. Consequently, the CTB played an important role in the separation of anoxic and oxic zones. Also, the each pollutans were reduced gradually along the height in the oxic zone. The reason is that the biomass in the media layer (Port 4 and 5) was higher than that in the mixed liquor layer without the media (Port 2 and 3).

• The Journal of the Petrological Society of Korea
• /
• v.14 no.4 s.42
• /
• pp.251-263
• /
• 2005

Modern volcanoes, Laoheishan and Huoshaoshan, have erupted during $1720\~1721$ in the Wudalianchi volcanic group, NE china. They comprise scoria and spatter cones that consist of potassium-rich phono-tephritic pyroclastic deposits and lavas, and include wide lava flow fields. The Laoheishan scoria cone is a polygenetic multiple volcano that overlaps earlier and later edifices with more complicated internal structures produced in greater scale and in earlier time than the Huoshaoshan. There is a funnel-shaped crater in the center of the later edifice of the Laoheishan scoria cone. The Huoshaoshan spatter cone is a monogenetic simple volcano with a central pit crater. The volcanic sequences indicate eruption processes that followed a repeated pattern that progressed through 5 stages of explosive and effusive eruption including lava fountains and Strombolian eruptions in the Laoheishan, and a recognizable pattern of 2 stages that started with Strombolian eruption and progressed through lava effusion in the Huoshaoshan.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.08a
• /
• pp.76.3-76.3
• /
• 2008