• 소성∙가공
• /
• 제25권4호
• /
• pp.268-274
• /
• 2016

In the automotive seat industry, the use of a fine blanking press is important for manufacturing of high precision products. Among them, a gear part which is a main component of an automotive seat recliner is generally manufactured by fine blanking press. However, the use of conventional mechanical press has been increasing in manufacture of gear part because of low productivity of fine blanking press. In this study, new forming process is suggested to fabricate the gear part with high precision by using mechanical press. The effect of flow restriction die (FRD) which has the restriction of blank edge on dimensional accuracy is investigated by FE-analysis. FE-analysis results for different conditions of FRD indicated that FRD has high dimensional accuracy with the lowest roll-over and the highest perpendicularity of gear part. After application to fabrication of the gear part using mechanical press, the measured dimensional characteristic was compared with the required specification of final product. In addition, results of the performance test showed that the product fabricated by developed process satisfied the required strength and durability. The results show that the suggested forming process by using FRD and mechanical press can replace fine blanking on the viewpoint of dimensional accuracy and productivity.

• Nuclear Engineering and Technology
• /
• 제41권7호
• /
• pp.885-892
• /
• 2009

This manuscript will discuss a numerical method where the six equations of two-phase flow, the solid heat conduction equations, and the two equations that describe neutron diffusion and precursor concentration are solved together in a tightly coupled, nonlinear fashion for a simplified model of a nuclear reactor core. This approach has two important advantages. The first advantage is a higher level of accuracy. Because the equations are solved together in a single nonlinear system, the solution is more accurate than the traditional "operator split" approach where the two-phase flow equations are solved first, the heat conduction is solved second and the neutron diffusion is solved third, limiting the temporal accuracy to $1^{st}$ order because the nonlinear coupling between the physics is handled explicitly. The second advantage of the method described in this manuscript is that the time step control in the fully implicit system can be based on the timescale of the solution rather than a stability-based time step restriction like the material Courant limit required of operator-split methods. In this work, a pilot code was used which employs this tightly coupled, fully implicit method to simulate a reactor core. Results are presented from a simulated control rod movement which show $2^{nd}$ order accuracy in time. Also described in this paper is a simulated rod ejection demonstrating how the fastest timescale of the problem can change between the state variables of neutronics, conduction and two-phase flow during the course of a transient.

• 한국전기전자재료학회논문지
• /
• 제31권1호
• /
• pp.61-67
• /
• 2018

High-power lithium batteries are suitable for equipment with high power output needs, such as for ESS's initial start-up. However, their management cost is increased by the installation of air-conditioning to minimize the risk of explosion due to internal temperature rise and also by a restriction on the number of charge/discharge cycles. High-capacity flow batteries, on the other hand, have many advantages. They can be used for over 20 years due to their low management costs, resulting from no risk of explosion and a high number of charge/discharge cycles. In this paper, we propose an ESS based on hybrid batteries that uses a lithium iron phosphate battery (LiFePO) at the initial startup and a vanadium redox flow battery (VRFB) from the end of the transient period, with a bi-directional PCS to operate two batteries with different DC voltage levels and using an efficient energy management control algorithm.

• 한국엔터테인먼트산업학회논문지
• /
• 제15권7호
• /
• pp.225-233
• /
• 2021

본 연구는 정상인을 대상으로 건강을 위한 유산소 능력과 관계가 깊은 하지에 혈류제한 유산소 훈련을 시행함으로써 하지 근활성도와 운동신경원을 정량적으로 비교·분석하여 효과적인 혈류제한 운동프로그램의 효용성을 제시하는 기초자료를 제공하고자 한다. 압력 정도가 140 mmHg으로 혈류제한하여 트레드밀 위에서 유산소 운동을 적용한 집단 10명을 실험군I, 트레드밀 위에서 유산소 운동만 적용한 집단을 11명을 대조군으로 각각 무작위 배치한 후, 트레드밀에서 4주간, 주 3회, 1일 1회, 1회 30분간 중재 프로그램을 시행하였다. 중재 전 표면근전도를 활용하여 근활성도와 운동신경원을 측정하여 분석하였다. 연구 결과는 실험군I의 집단 내 전후 비교에서 넙다리곧은근, 넙다리두갈래근, 앞정강근 및 장딴지근의 근활성도가 유의하게 증가하였다(p<.001). 대조군의 집단 내 전후 비교에서는 넙다리곧은근, 넙다리두갈래근, 앞정강근 및 장딴지근의 근활성도가 유의하게 증가하였다(p<.001). 집단 간 변화 비교에서는 넙다리곧은근의 활성도가 유의한 차이가 있었다(p<.05). 하지 혈류제한과 병행하여 유산소운동을 접목하는 것은 엘리트선수 육성과 관절이 약한 노인 등 재활 트레이닝에 기능적인 활동을 회복시킬 수 있는 부상방지 운동프로그램 등으로 발전시킬 수 있을 것이며, 향후 연구에서 이러한 결과를 바탕으로 하여 정상인이 아닌 대상의 영역을 확대하고, 압력강도에 따른 다각적인 연구들이 필요할 것으로 사료된다.

• 설비공학논문집
• /
• 제28권8호
• /
• pp.337-342
• /
• 2016

A marine SCR System is emerging as an alternative to comply with NOx Tier III Emission standards, a restriction on greenhouse gas from vessels implemented by the International Maritime Organization. The system is greatly affected by the uniformity of the fluid flowing into the catalyst, so the performance of the catalyst of an SCR system needs to be guaranteed. This study conducted research on a mixed evaporator of an SCR system, which is one of the factors affecting the uniformity of the fluid. When the angle of the mixed evaporator is set to $90^{\circ}$, the fluid uniformity is at its highest at 83%, under the condition that the length of the mixed evaporator be 3.5 D. When the length was 3.5 D and less, the fluid uniformity had a tendency to improve relative to the case without a bent pipe. However, a longer mixed evaporator results in a more perfect liquidity development in the pipe with a liquidity distribution similar to the case where no curved pipe is formed in front of the catalyst. A lower angle for the mixed evaporator results in a lower flow uniformity, and a longer length of the mixed evaporator results in a lower difference in the flow uniformity caused by the angle. The flow uniformity can be improved by 6% with a mixed evaporator, which confirmed that all factors applied to an SCR system have a close relationship with the efficiency.

• 지질공학
• /
• 제20권2호
• /
• pp.169-181
• /
• 2010

지질구조 요소 중 산성 암맥은 K-1 유류비축기지에서 지하수 유동에 직접적인 영향을 미칠 수 있다. 산성 암맥의 산출 특성과 기지 주변의 수리지질학적 조건을 토대로 지하수 모델링을 수행하였으며, 자연적 또는 인위적으로 가능한 시나리오를 구성하여 기지 인근 지역의 지하수위 변화 스트레스에 대한 반응을 모의하였다. 기지 주변에서 24개의 가상적인 우물들을 활성화하고 4단계 양수량 변화에 따른 수위 영향반경의 변화를 고려함으로써, 비축기지 내 안정적 수위 유지를 위해 다음과 같이 5개의 구획을 구분하여 양수량 제한 구역 설정을 제안하였다; zone I (기지에서 300 m 이내 범위), 50 $m^3/day$ 이하; zone II (기지에서 300~600 m 범위), 75 $m^3/day$ 이하; zone III (기지에서 600~900 m 범위), 150 $m^3/day$ 이하; zone IV (기지에서 900~1,200 m 범위), 300 $m^3/day$ 이하; zone V (산성암맥 주변). 산성 암맥을 따른 zone V에서는 맥암으로부터 70~100 m 거리까지 양수의 영향이 나타날 수 있으므로 다른 지점들에 비해 특별히 지하수 사용에 대한 제한과 주의가 요구된다.

• 한국전자통신학회논문지
• /
• 제15권5호
• /
• pp.949-958
• /
• 2020

차량을 구성하는 엔진, 미션, 현가, 제동, 조향장치 등 다양한 장치 중에서 현가 장치는 타이어와 차체 사이에 설치되어 노면에 의한 차량의 진동을 억제하여 승차감을 향상시키고 차륜과 노면 사이에 적절한 접지력을 유지시켜 차량의 조정안정성을 향상시키는 등 차량역학적인 측면에서 많은 영향을 미치는 장치 중의 하나이다. 본 연구에서는 차량용 현가 장치의 충격 흡수기를 실제 특성과 유사한 상세 모델로 모델링하고, 충격 흡수기의 주요 설계변수의 불확실성을 통계적으로 고려하여 설계변수의 불확실성이 현가 장치의 동적 특성에 미치는 영향에 대하여 연구하였다.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2006년 제4회 한국유체공학학술대회 논문집
• /
• pp.49-52
• /
• 2006

should be in English, A make out an economical, reliable and easy to adoptable instrument in turbine discharge measurement was restricted from lots of it's foundational condition. Not with standing the brilliant progress in new technology of these day, useful instrument for flow measurement in turbine is still ongoing. Nowaday, the increasing importance of renewable energy makes it more important that the measuring turbine efficiency as a decision making index of old turbines' replacement. In Turbine performance diagnosis, Kwater(Korea Water Corporation) got an enough ability and decent reputation for who has invested lots of time and effort for buildup and development. In Korea as a public corporation who should take a crucial roll in Turbine business, Kwater has introduced some developed new technology for other domestic concerned one. With this writing, I'd like to introduce ASFM system as a newly developed instrument that can cope with lots restriction in discharge measurement in turbine. Kwater adopted the system in 2005, and performed 2 times of trial test. The test result was good enough to use the system as a reference test method.

• 대한기계학회논문집A
• /
• 제27권6호
• /
• pp.1007-1013
• /
• 2003

As environmental restriction kas continuously become more strict, machining technology has emphasized on development of environment-friendly technology. In cutting technology, it has been well recognized that cutting fluids might have undesirable effects on workers health and working environment. In this study, compressed cold air was used as a replacement for conventional cutting fluids. The cooling effect on cutting tool was analyzed using the finite element method and the computational fluid dynamics. This study focused on the temperature simulation of cutting tool by real flow analysis of cold air. The maximum flow rate and the minimum temperature of compressed cold air are 300ι/min and -30$^{\circ}C$ respectively. To compare the simulation and experimental results, inner temperature of the cutting tool was measured with the thermocouple embedded in the insert. The results show that the analysis of cutting temperature using FEM and CFD is resonable, and the replacement of cutting fluid with cold air is available.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• 제17권3호
• /
• pp.197-207
• /
• 2013

The Cahn-Hilliard equation was proposed as a phenomenological model for describing the process of phase separation of a binary alloy. The equation has been applied to many physical applications such as amorphological instability caused by elastic non-equilibrium, image inpainting, two- and three-phase fluid flow, phase separation, flow visualization and the formation of the quantum dots. To solve the Cahn-Hillard equation, many numerical methods have been proposed such as the explicit Euler's, the implicit Euler's, the Crank-Nicolson, the semi-implicit Euler's, the linearly stabilized splitting and the non-linearly stabilized splitting schemes. In this paper, we investigate each scheme in finite-difference schemes by comparing their performances, especially stability and efficiency. Except the explicit Euler's method, we use the fast solver which is called a multigrid method. Our numerical investigation shows that the linearly stabilized stabilized splitting scheme is not unconditionally gradient stable in time unlike the known result. And the Crank-Nicolson scheme is accurate but unstable in time, whereas the non-linearly stabilized splitting scheme has advantage over other schemes on the time step restriction.