• Journal of Korean Society of Water and Wastewater
• /
• v.19 no.2
• /
• pp.155-160
• /
• 2005

Gravity thickening process has been widely used in WTP sludge thickening at domestic water treatment plant. The operation method of the process is very simple, however, the process requires long detention time about 24~48 hours for sludge thickening, uses polymer, and low total solids of thickened sludge to increase sludge thickening efficiency. To solve there problems, we studied about flotation process, especially, electro-flotation (EF) process in WTP sludge thickening. Electro-flotation process is simpler than dissolved-air-flotation(DAF) process because EF needs only electrode and current to generate micro-bubbles and the operation is easy. This study was performed at two batch columns to compare interface height, total solids, effluent turbidity between an electro-flotation thickening and a gravity thickening. According to the result, an electro-flotation thickening was that interface height was decreasing, total solids had high concentration, and effluent turbidity was low in comparison with a gravity thickening. Also, it will make the high efficiency of following process, such as a dehydrating process and digestive process. because of high total solids and low moisture content in the sludge.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.33 no.1
• /
• pp.1-7
• /
• 2001

The immediate purposes of this study is to establish the surface chemical principles associated with the flotation process of waste papers and to verify them by practical flotation experiments. To achieve this AKD sized hydrophobic microcrystallince cellulose (MCC) with different levels of hydrophobicity, and hydrophilic MCC dyed with black were prepared as model substances. The effects of surface characteristics on flotation efficiency were evaluated by measuing the brightness of the flotation rejects obtained after the flotation experiments carried out using MCC mixtures prepared with different ratios of hydrophobic and hydrophilic MCCs. Results showed that more than 90% of the flotation rejects consisted of hydrophobic MCC indicating the critical importance of the hydrophobicity of the materials in the flotation process. The proportions of hydrophobic materials in the reject remained constant when highly sized MCC was used as a model of hydrophobic substance.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.36 no.2
• /
• pp.33-38
• /
• 2004

Toner particles used in laser and xerographic printing process is fused on paper surface so strongly that they tend not to detach easily from the recylced paper surface during pulping. Furthermore, the removal efficiency of detached toner particles by conventional screening and flotation process has limitation due to the platy shape and large size of detached toner particles. It has been shown that the removal efficiency of toners in the screening process can be increased by agglomerating the toner particles with fatty alcohol. It is not possible, however, to remove small and platy toner particles by screening process. These small and platy toner particles should be removed by flotation process. In this study the effect of fatty alcohol that used for toner agglomeration on flotation efficiency has been examined. It was shown that flotation efficiency decreased when fatty alcohol was used most probably due to its effect of reducing hydrophobicity of toner particles.

• Journal of Korean Society of Water and Wastewater
• /
• v.20 no.2
• /
• pp.245-255
• /
• 2006

Dissolved air flotation is a solid-liquid separation system that uses fine bubbles rising from bottom to remove particles in water. In order to enhance the flotation velocity and removal efficiency of flocs in the flotation process, we tried to obtain pretreatment conditions for the optimum DAF process operation by comparing and evaluating features of actual floc formation and flotation velocity etc, according to coagulant types and conditions for flocculation mixing intensity by using PIA, PDA, and FSA. Accordingly, generating big flocs that have low density at low flocculation mixing intensity may reduce treatment efficiency. In addition, generating small flocs at high flocculation mixing intensity makes floc-bubbles smaller, which reduces flotation velocity, In this study, it was found that high flocculation mixing intensity could not remove the remaining micro-particles after flocculation, which had negative effects on treated water quality, Therefore, in order to enhance treatment efficiency in a flotation process, flocculation mixing intensity around $50sec^{-1}$ is effective.

• Journal of Korean Society on Water Environment
• /
• v.28 no.3
• /
• pp.367-374
• /
• 2012

A flotation process has a shorter processing time and needs less space than a sedimentation process. Dissolved air flotation process (DAF) is an efficient flotation method and used in a conventional wastewater treatment process. However, DAF requires the circulation of water containing compressed air and requires expensive installation and operation cost. Plasma Air Flotation (PAF) process is able to float flocs by micro bubbles generated from underwater plasma without the circulation of bubbly water and additional saturators. Therefore, PAF can be an alternative solution overcoming economic barriers. In this study, Humic acid removal efficiency by PAF process was compared with that of sedimentation process. 44.67% and 87.3% reduction rate based on UV 254 absorbance has been measured in sedimentation and PAF respectively. In particular, PAF in the flocculation zone can dramatically remove humic acid from water. In flocculation zone, PAF can separate organic matters but sedimentation cannot.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.37 no.3
• /
• pp.1-8
• /
• 2005

Increase in the utilization rate of recycled paper and closing level of papermaking system increased the problem associated with stickies that include decrease in process runnability and product quality. It is required to establish a process for removing the micro stickies to solve the problems associated with stickies. In this study, the application of flotation process as a method to remove micro stickies was examined. Model micro stickies (MMS) were prepared using microcrystalline cellulose (MCC) and pressure sensitive adhesives (PSA), and the influence of three nonionic surfactants on the removal efficiency of MMS from flotation process was examined. Also the effect of surfactants on the deposition of micro stickies that remaining in the papermaking wet end onto wire was examined. Removal efficiency of MMS by flotation was increased when the proportion of nonionic surfactant with propylene oxide (PO) type hydrophilic tail was increased and stock pH was 7. It was suggested that this nonionic surfactant minimized the increase of surface energy of hydrophobic MMS. The MMS with high hydrophobicity remaining in the papermaking system, however, would cause more serious deposition problems on papermaking wet end. Therefore, it is of great importance to increase the removal efficiency of MMS in flotation process for the prevention of papermaking system contamination caused by stickies deposition.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.31 no.1
• /
• pp.10-16
• /
• 1999

Air froth flotation was applied to OCC recycling process as a new pulp fractionation method and the effects of strength and drainage properties of testliner were also investigated. Fines including inks, stickies, and inorganic substances in OCC stock furnish were efficiently separated by the flotation. After the flotation, selective enzymatic treatment on the flotation reject was separately preformed, and then, the refined long fiber(flotation accept) portion was combined again with the fines(flotation reject) fraction for papermaking. This combination process was found to be effective in improving strength and drainage properties of testliner based on 100% OCC.

• Journal of Korean Society of Water and Wastewater
• /
• v.25 no.4
• /
• pp.471-478
• /
• 2011

A series of laboratory experiments carried out to investigate the particle separation efficiency and flotation characteristics using $CO_2$ bubbles. The primary objective of this study was to find out the feasibility of $CO_2$ bubbles as an applicable unit of flotation process in tap-water and wastewater treatment plant. The fundamental measurements were conducted to characterize the $CO_2$ bubble from the physical viewpoint in water including bubble size distribution and rising velocity under various operational conditions. In addition, the removal efficiency of solid was experimented using the lab scale plant applied $CO_2$ bubbles, namely the dissolved carbon dioxide flotation (DCF) process. The DCF process using carbon dioxide bubble, which is an advantage as the decrease and the reuse of Green-House gas, can be a promising technology as an water treatment process. On the other hand, the further research to decrease the bubble size distribution of $CO_2$ is required to enhance the particle separation efficiency.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2010.04a
• /
• pp.7-7
• /
• 2010

Flotation deinking is a common practice for removing ink from recovered paper, and it is becoming a key process in many recycling paper mills. Flotation deinking was successfully introduced to the paper recycling industry in the 1980s, and its applications in wax removal, stickies control, and fiber fractionation have attracted great research interest. A successful flotation process has three major efficient subprocesses: the detachment of the ink particles from the fibers, the effective adhesion of the ink particles onto air bubble surfaces, and the removal of froth and ink particles from flotation cells. Surfactants can affect these subprocesses either positively or negatively. To understand how a surfactant can positively and negatively affect the flotation deinking process, the basic chemistry of surfactant in solution should be discussed.

• Resources Recycling
• /
• v.33 no.2
• /
• pp.37-45
• /
• 2024

Molybdenum is used in various industries because of its high heat and corrosion resistance. It was selected as a critical mineral in Korea. However, there have been recent challenges in production because of the increased depth and decreased grade of molybdenum veins. Consequently, it is necessary to enhance the effectiveness of the molybdenum beneficiation process. In this study, a basic evaluation of beneficiation characteristics was conducted to enhance the effectiveness of the domestic molybdenum ore beneficiation process. The properties of the beneficiation process were assessed using mineralogical analysis, work index, and flotation kinetics. The results revealed that the allowable particle size of the molybdenum ore for liberation was ~100 ㎛. In addition, the work index was calculated to be 14.57 kWh/t. The operating conditions in the flotation units were achieved by determining the optimal flotation time for each process based on flotation kinetics. Finally, the characteristics of molybdenum ore beneficiation provided in this study can be utilized to diagnose the grinding and flotation processes of large-scale molybdenum beneficiation plants.