• International Journal of Aerospace System Engineering
• /
• 제6권1호
• /
• pp.1-7
• /
• 2019

In the present study, structural safety and stability on the main wing and tail planes of the 1.2 ton WIG(Wing in Ground Effect) flight vehicle, which will be a high speed maritime transportation system for the next generation, was performed. The carbon-epoxy composite material was used in design of wing structure. The skin-spar with skin-stressed structural type was adopted for improvement of lightness and structural stability. As a design procedure for this study, the design load was estimated with maximum flight load. From static strength analysis results using finite element method of the commercial codes. From the stress analysis results of the main wing, it was confirmed that the upper skin structure between the second rib and the third rib was unstable for the buckling load. Therefore in order to solve this problem, three stiffeners at the buckled region were added. After design modification, even though the weight of the wing was a little bit heavier than the target weight, the structural safety and stability was satisfied for design requirements.

• 한국시뮬레이션학회논문지
• /
• 제26권1호
• /
• pp.13-19
• /
• 2017

국내 유도무기 개발과정에서 가장 일반적으로 적용되는 M&S 도구는 유도탄의 각 구성품 및 공력특성 모델을 반영한 6자유도 비행모의 프로그램이다. 하지만 3세대 대전차 유도무기와 같이 영상탐색기가 적용되는 경우 6자유도 비행모의만으로 다양한 조건 하에서의 체계 성능을 확인할 수 없다. 영상탐색기의 추적 성능은 표적의 대조비나 온도차뿐만 아니라 유도탄 거동에 따른 표적 위치 이격, 회전 등에 민감하게 반응하기 때문에 유도무기 개발 과정에서 영상 추적 성능과 유도탄 비행성능을 통합하여 분석할 수 있는 M&S 도구가 요구된다. 3세대 대전차 유도무기인 현궁 개발 과정에서는 형상 설계 단계부터 '합성영상 생성 S/W'-'영상추적기'-'비행모의 프로그램'을 연동한 통합비행 M&S 도구를 개발, 적용하였다. 통합비행 M&S 도구 기반으로 몬테카를로 시뮬레이션을 수행한 후 체계 주요 성능 지수, 즉 명중률 비교를 통해 적합한 형상을 선정하였다. 본 논문에서는 3세대 대전차유도무기 형상설계를 위한 고려요소와 함께 통합비행 M&S 방법론 및 분석 결과를 기술하였다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1992년도 한국자동제어학술회의논문집(국제학술편); KOEX, Seoul; 19-21 Oct. 1992
• /
• pp.344-348
• /
• 1992

This paper describes a procedure to design a hovering flight controller for a model helicopter using LQG theory. Parameters of the model helicopter in hover are obtained using direct measurements and calculations proposed by other research. A feedback co is by using digital LQG theory. First, a full state feedback controller is designed to the discretized system taking desirable transient response and other assumptions into account. Then a full-state estimator is designed and revised until desirable response is obtained while global stability is maintained. Performance of the controller is tested by computer simulations. Experiments have been performed using a 3-degree-of-freedom gimbal that holds the model helicopter, and the controller exhibited stable hover capability.

• 한국항행학회논문지
• /
• 제28권3호
• /
• pp.272-277
• /
• 2024

대부분 국가에서 계기비행 절차는 국제민간항공기구(ICAO)의 DOC 8168, 항행 서비스 및 운항 절차(PANS-OPS) 또는 미국 연방항공청(FAA)의 터미널 절차(TERPS) 중 한 가지 기준을 적용해 설계된다. 특히, 선회접근 절차는 두 기준이 서로 많은 차이를 갖고 있고, 미국 터미널 절차(TERPS)는 2013년 이후에는 고도에 따라 확장된 기준을 적용함으로써 더 복잡해졌다. 선회접근 절차는 착륙을 위해 항공기를 에너지가 낮은 상태에서 지면과 가깝게 기동하는 것을 포함하므로 직진접근 절차보다 더 위험에 노출된다. 본 연구에서는 이들 차이점을 정확하게 알기 위해 선회접근 절차가 국내의 개별 공항에 따라 어떤 기준에 의해 설계되었는지를 구분하고, 선회접근 기동 중 최소장애물 회피를 보장하는 선회접근 구역 범위를 위한 반경을 산출하고, 안전한 선회접근 절차 수행을 위한 방법을 제시한다.

• 한국항공우주학회지
• /
• 제41권8호
• /
• pp.657-664
• /
• 2013

상용 프로그램 MSC/NASTRAN의 FlightLoad를 사용하여 고세장비 유연날개 항공기의 하중해석을 수행하였다. 풍동시험 결과를 이용하여 공력모델을 보정하고, 항공기의 모든 기동조건을 묘사하기 위한 트림조건을 정립하였다. 또한 항공기 중량 모델링, 설계 임계조건 판단 및 해석용 하중카드 생성 등 모든 업무를 자동으로 생성할 수 있는 프로그램을 개발하였다. 이러한 기법과 프로그램을 이용하여 효율적인 항공기 개발을 위한 비행하중해석 절차를 수립하였다.

• Advances in aircraft and spacecraft science
• /
• 제6권5호
• /
• pp.349-369
• /
• 2019

In the design of flight control systems there are issues that deserve special consideration and attention such as external perturbations or systems failures. A Simple Adaptive Controller (SAC) that does not require a-priori knowledge of the faults is proposed in this paper with the aim of realizing a fault tolerant flight control system capable of leading the pitch motion of an aircraft. The main condition for obtaining a stable adaptive controller is the passivity of the plant; however, since real systems generally do not satisfy such requirement, a properly defined Parallel Feedforward Compensator (PFC) is used to let the augmented system meet the passivity condition. The design approach used in this paper to synthesize the PFC and to tune the invariant gains of the SAC is the Population Decline Swarm Optimization ($P_DSO$). It is a modification of the Particle Swarm Optimization (PSO) technique that takes into account a decline demographic model to speed up the optimization procedure. Tuning and flight mechanics results are presented to show both the effectiveness of the proposed $P_DSO$ and the fault tolerant capability of the proposed scheme to control the aircraft pitch motion even in presence of elevator failures.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 추계학술발표대회 논문집
• /
• pp.179-184
• /
• 2005

In the present study, conceptual design of the main wing for 20 seats WIG{wing in Ground Effect) flight vehicle, which will be a high speed maritime transportation system for the next generation, was performed. The high stiffness and strength Carbon-Epoxy material was used for the major structure and the skin-spar with a foam sandwich structural type was adopted for improvement of lightness and structural stability. As a design procedure for this study, firstly the design load was estimated with maximum flight load, and then flanges of the front and the rear spar from major bending load and the skin structure and the webs of the spars were preliminarily sized using the netting rules and the rule of mixture. In order to investigate the structural safety and stability, stress analysis was performed by Finite Element Codes such as NASTRAN/PA TRAN[6] and NISA II [7]. From the stress analysis results, it was confirmed that the upper skin structure between the front spar and rear spar was very unstable for the buckling. Therefore in order to solve this problem, a middle spar and the foam sandwich structure at the upper skin and the web were added. After design modification, even thought the designed wing weight was a little bit heavier than the target wing weight, the structural safety and stability of the final design feature was confirmed. Moreover, in order to fix the wing structure at the fuselage, the insert bolt type structure with six high strength bolts was adopted for easy assembly and removal.

• Journal of Mechanical Science and Technology
• /
• 제17권2호
• /
• pp.187-196
• /
• 2003

In this paper, a new methodology of evolutionary computations - An Adaptive Evolutionary Algorithm (AEA) is proposed. AEA uses a genetic algorithm (GA) and an evolution strategy (ES) in an adaptive manner in order to take merits of two different evolutionary computations : global search capability of GA and local search capability of ES. In the reproduction procedure, the proportions of the population by GA and ES are adaptively modulated according to the fitness. AEA is used to. designing fuzzy logic controller (FLC) for a high-angle-of-attack flight system for a super-maneuverable version of F-18 aircraft. AEA is used to determine the membership functions and scaling factors of an FLC. The computer simulation results show that the FLC has met both robustness and performance requirements.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 추계학술대회 논문집 학회본부 B
• /
• pp.457-459
• /
• 1998

This paper presents a 3-DOF hovering flight controller for a model helicopter using the minimal order LQG/LTR technique. A model helicopter is an unstable multi-input multi-output nonlinear system strongly exposed to disturbances, so a robust multi-variable control theory should be applied to control it. The minimal order LQG/LTR technique which uses a reduced-order observer in the LTR procedure is used to design the controller. Performances for the 3-DOF hovering flight controller are evaluated through computer simulations.

• 한국항공우주학회지
• /
• 제40권9호
• /
• pp.800-806
• /
• 2012

본 논문은 지상지원과 지상관제의 기능을 결합한 무인항공기의 비행시험을 위한 통합형 지상지원시스템(Ground support system)에 대한 설계 및 개발에 관해 기술한다. 통합비행시험은 비행체의 성능을 검증하기 위한 필수적인 절차이다. 개발한 통합형 지상지원시스템은 비행시험에 필요한 인적 물적 자원과 시간을 절감하고 비행시험의 체계적인 준비와 진행을 하기 위한 인프라로써 비행시험의 제반 사항을 갖추어 지상관제, 통신, 발전, 장비의 수송, 수리와 유지 등이 가능하며 소규모 연구소에서 2~3명의 인원으로 운용하기에 적합한 수준이다.