• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.1864-1866
• /
• 1997

Uncertainties in the aerodynamic coefficients or time delay effects in implementing an autopilot algorithm can make a Flight Control System(FCS) unstable. When a FCS enters unstable state, the actuator or sensor limiters in FCS make the unstable system not diverge but be in the state of stable limit cycle. If an autopilot recognize the FCS to be in the stable limit cycle phenomenon, it woudl be better to adjust autopilot gains to stabilize the FCS. A novel method to stabilize a FCS using parameter estimation and maintenance of given phase margin is proposed. The method is applied to roll control loop and verified its performance.

• International Journal of Aeronautical and Space Sciences
• /
• v.2 no.2
• /
• pp.95-107
• /
• 2001

This paper is devoted to the parameter optimization of unmanned aerial vehicle's (UAV) flight control laws. Optimization procedure is based on the ideas of mixed $H_2/H_{\infty}$ control of multi-model plants. By using this approach, some partial $H_2$-terms defining the performance of nominal and parametrically perturbed Flight Control System (FCS) responses to deterministic command signals in stochastic atmosphere as well as $H_{\infty}$-terms defining robustness of the FCS can be incorporated in the composite cost function. Special penalty function imposed on the location of closed-loop system's poles keeps the speed of response and oscillatory properties for both nominal and perturbed FCS in reasonable limits. That is the reason why this procedure may provide reasonable trade-off between the performance and robustness of FCS that are very important especially for UAV. Its practical importance is illustrated by case studies of lateral and longitudinal control of small UAV.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.141.3-141
• /
• 2001

Since 1990´s, there has been many researches for the development of the Unmanned Aerial Vehicle (UAV). Especially, for the development of digital electronics, the technologies of UAV toward to the miniaturization low-cost, and high reliability. Therefore, recent trends for the development of UAV are focused on the development modern Flight Control System (FCS). In this paper, focusing on the FCS, the development process for Sejong Unmanned Research Vehicle -1 (SURV-1) from design to flight test is presented.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.11
• /
• pp.33-40
• /
• 2005

The reliability of flight control system(FCS) for Unmanned Air Vehicle(UAV) is underestimated because of the design restrictions such as small size, low cost and light weight. However because the failure of FCS may cause the loss of aircraft, the reliability of FCS must be analysed and validated whether it meet the reliability requirements in design phase.In this paper the failure rate of subsystems was divided with its function based on the design experience of FCS. The redundancy models which satisfy the system reliability requirements were suggested. These results may be utilized in the hardware design of FCS.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.8
• /
• pp.833-842
• /
• 2011

The objectives of this research are development of guidance, navigation and control system for RUAV on virtual instrumentation and real flight test. For this research, the system is divided to DAQ (data acquisition) section, actuator section and controller section. And the hardware and software on each sections are realized on LabVIEW base. Waypoint guidance and control of auto flight are realized using PID gain tuning and waypoint vector tracking guidance algorism. For safe flight test, auto/manual switching module isolated from FCS (Flight Control System) is developed. By using the switch module, swift mode change was achieved during emergency flight case. Consequently, a meter level error of flight performance is achieved.

• International Journal of Control, Automation, and Systems
• /
• v.5 no.1
• /
• pp.104-109
• /
• 2007

This paper is about a redundancy management system design for the Smart UAV(unmanned aerial vehicle) which utilizes the tilt..rotor mechanism. In order to meet the safety requirement on the PLOC(probability of loss of control) of $1.7{\times}10^{-5}$ per flight hour for FCS (flight control system) failures, a digital FCS is mechanized with a dual redundant structure. A fault detection system which is composed of a CCM(cross channel monitor) and analytic redundancy using the Kalman filtering is designed, and its effectiveness is evaluated through experiments. A threshold level and persistence count for managing redundant sensors are designed based on the statistical analysis of the FCS sensors. To increase the survivability of the UAV after the loss of critical sensors in the SAS(stability augmentation system) and to provide reference information for a tie-breaking condition at which an ILM(in-line monitor) cannot distinguish the faulty channel between two operating ones, the Kalman filter approach is investigated.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.46 no.6
• /
• pp.73-79
• /
• 2009

For the shake of control for movement object, control theory like neural network, nonlinear model predictive control(NMPC) is realized on digital high speed computer. Predictor of flight control system(FCS) based nonlinear model predictive control has to be satisfied with response for hard real-time to perform applications on each module in the FCS. Simultaneously, It gives a serious consideration accuracy to give full play to FCS's performance. Error of mathematical aspect affects realization of whole algorithm. But factors of bring mathematical error is not considered to calculate final accuracy on parameter of predictor. In this paper, Predictor was made using load control model on the digital computer for design FCS at hard real-time and is shown response time on realization algorithm. And is shown realization algorithm of high effective predictor over the accuracy. The predictor was realized on the load control model using Euler method, Heun method, Runge-Kutta and Taylor method.

• Journal of Aerospace System Engineering
• /
• v.16 no.1
• /
• pp.70-80
• /
• 2022

An aerial refueling provides for extension of operational time and range for aircraft and enhances mission effectiveness, hence it application by most military aircrafts. The receiver aircraft should have the aerial refueling clearance that is established by performing technical and operational compatibility assessments to certify it for aerial refueling with a specific tanker model. The compatibility assessment includes aerial refueling handling qualities, functional, fuel, lighting system testing and it is finally verified through flight testing. However, since aerial refueling compatibility assessments have never been performed in Korea, there is no experience to determine the test requirements and the scope and size of the test program for a new development aircraft. This paper therefore introduces the common techniques of aerial refueling and aerial refueling flight test methods to understand the aerial refueling FCS (Flight Control System), OFP (operational flight program) and system validation, and aerial refueling envelope clearance of a fixed wing aircraft for a boom and receptacle refueling system that is being introduced into Korea Air Force.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.10
• /
• pp.46-52
• /
• 2004

A design methodology of the redundancy management for a duplex FBW flight control system is introduced. A statistical analysis is applied to determine two design parameters in CCM(Cross Channel Monitor), threshold and persistence count. An analytic redundancy, which is implemented using a Kalman filtering algorithm is considered. The application of an analytic redundancy to the FCS design of the smart UAV has several advantages of increasing the aircraft's survivability and breaking the tie-condition for a duplex FCS. All the redundancy management algorithms are verified through the numeric simulation for the flight dynamics of the XV-15 tilt rotor.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.6 no.4
• /
• pp.22-28
• /
• 2003

In the conventional weapon system, such as gun and small arms, it Is a general trend that for maximization of its performance and enhancement of its effectiveness, the firing control system(FCS) is developed and applied with the guns and small arms in the world. The FCS of the small arms for infantry man is composed of a few of sensors for acquisition of input data of FCS, such as range measurement, position sensing of weapon, temperature, etc., computer, displayer and power pack, and also the air burst munition is developed in parallel for the maximization of FCS's effectiveness. Since the flight time setting fuze for the air burst munition is adapted for next me, the measuring device of the muzzle velocity is needed to overcome the variation of muzzle velocity due to producing procedures and the differences of the using temperatures and so maintain the burst position accuracy This paper contained the technical information on the development of the measuring device of muzzle velocity, which designed in compact & light weight configuration with reliability and accuracy.