• Journal of the Korean Society for Marine Environment & Energy
• /
• v.13 no.3
• /
• pp.216-222
• /
• 2010

The structural methods used to protect coastal erosion are usually very expensive in construction as well as in spending on maintaining the structures from damage. Those structures like embankments, breakwaters, jetties etc. are commonly constructed with concretes (rigid methods) to protect coastal erosion. But those rigid methods are not effective always, because the wave energy and impact force on the structures could not be effectively reduced by those methods. For avoiding sediment erosion on coastal areas by the way of reducing wave energy, a flexible breakwater is introduced which will reduce energy and protect coastline economically and environmentally. The flexible device is a combination of flexible wire nets and stack of rings made of used vehicle tires and soft blades on surfaces. This flexible wire net is placed in between two stacks of rings. The stack of rings is mainly used to hold the flexible wire nets and the flexible wire net is mainly used to reduce wave energy and helps to deposit sediments in coastal area. For a field experiment study, the above-mentioned flexible breakwater of coastal protection has been set up at the Shuang-Chun coastal area in Tainan County since June 10, 2009. The length of the flexible device is 50.0 meters and the height is 2.0 meters. The function of the device has been examined by Typhoon Linfa during June 19~22, 2009 and by Typhoon Morakot during August 6~10, 2009. The result shows that the flexible breakwater has effectively trapped sediments and let them deposit on coastal. The depth of sediment deposition around the device was about 0.5 to 0.8 meters.

• IE interfaces
• /
• v.11 no.2
• /
• pp.211-225
• /
• 1998

As mentioned in Part I all groupware products have been categorized into three areas which include cooperation/document management systems(CMS), collaborative writing systems(CWS), and decision-making/meeting system(DMS). This study deals with a comparative analysis of the last two areas, which is added to the first. It turns out that DMS has a higher market share than CWS. However. since effective collaboration requires the functions inherent to these two systems. they should be integrated somehow. The systems' functions that have been implemented in response to design issues have been described. Each group of the functions has been divided into three parts which consist of basic function, quasi-basic function. and others. Such a decision has been made according to the frequency rate of the functions provided in the products. While the basic functions in CWS include collaboraive writing beyond restriction of time and place, group awareness. version control. and others, in DMS realtime collaboration. brainstorming. presentation. various task support. policy formation. document management, multimedia, subgroup communication. topic commenter, categorizer, screen capture and various rile transfer. The basic functions are merged into the integrated functional model which was proposed in Part I. Since the model is so flexible that it can partially include the quasi-functions in addition to the hasic functions. a large number of products may stem from the modification of the functional model.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.10
• /
• pp.2287-2293
• /
• 2009

Gas Chromatography-Mass Spectrometry (GC-MS) fingerprint analysis, Principle Components Analysis (PCA), and Hierarchical Cluster Analysis (HCA) were introduced for quality assessment of Curcuma longa L. (C. longa). The GC-MS fingerprint method was developed and validated by analyzing 33 batches of samples of C. longa from different geographic locations. 18 chromatographic peaks were selected as characteristic peaks and their relative peak areas (RPA) were calculated for quantitative expression. Two principal components (PCs) were extracted by PCA. C. longa collected from Guizhou and Fujian were separated from other samples by PC1, capturing 71.83% of variance. While, PC2 contributed for their further separation, capturing 11.13% of variance. HCA confirmed the result of PCA analysis. Therefore, GC-MS fingerprint study with chemometric techniques provides a very flexible and reliable method for quality assessment of C. longa.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.44 no.3
• /
• pp.128-135
• /
• 2018

Objectives: The role of alloplastic materials in maxillofacial reconstruction is still controversial. Determining the utility of porous, high-density, polyethylene implants as a highly stable and flexible, porous alloplast, with properties such as rapid vascularization and tissue ingrowth, is crucial in cases of maxillofacial deformities and aesthetic surgery. Materials and Methods: Thirty high-density porous polyethylene implants were implanted in 16 patients that had been referred to a private office over a three-year period. These implants were used for correcting congenital deformities, posttraumatic defects and improving the aesthetic in nasal, paranasal, malar, chin, mandibular angle, body and orbital areas. Results: The outcomes of the cases in this study showed good aesthetic and functional results. The majority of patients had no signs of discomfort, rejection or exposure. Two implants suffered complications: a complicated malar implant was managed by antibiotic therapy, and an infected mandibular angle implant was removed despite antibiotic therapy. Conclusion: Based on the results, the Medpor implant seems to be an excellent biomaterial for correcting various facial deformities. Advantages include its versatility and relatively ideal pore size that allows for excellent soft tissue ingrowth and coverage. It is strong, flexible and easy to shape.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.287-287
• /
• 2010

We report a new direct patterning method, called liquid bridge-mediated nanotransfer molding (LB-nTM), for the formation of two- or three-dimensional structures with feature sizes between tens of nanometers and tens of micron over large areas. LB-nTM is based on the direct transfer of various materials from a mold to a substrate via a liquid bridge between them. This procedure can be adopted for automated direct printing machines that generate patterns of functional materials with a wide range of feature sizes on diverse substrates. Arrays of TIPS-PEN TFTs were fabricated on 4" polyethersulfone (PES) substrates by LB-nTM using PDMS molds. An inverted staggered structure was employed in the TFT device fabrication. A 150 nm-thick indium-tin oxide (ITO) gate electrode and a 200 nm-thick SiO2dielectric layer were formed on a PES substrate by sputter deposition. An array of TIPS-PEN patterns (thickness: 60 nm) as active channel layers was fabricated on the substrate by LB-nTM. The nominal channel length of the TIPS-PEN TFT was 10 mm, while the channel width was 135 mm. Finally, the source and drain electrodes of 200 nm-thick Ag were defined on the substrate by LB-nTM. The TIPS-PEN TFTs can endure strenuous bending and are also transparent in the visible range, and therefore potentially useful for flexible and invisible electronics.

• Journal of the Korean Institute of Rural Architecture
• /
• v.23 no.2
• /
• pp.9-16
• /
• 2021

The purpose of this study is to maintain the existing characteristics of the city by utilizing the physical decline status and floating population in small and medium cities residential areas. In addition, it intends to present the direction of flexible urban regeneration and maintenance by reflecting regional characteristics and current status. A total of three data were used in this study. Building data, floating population data, and census output area data were used. Building data and floating population data were classified into five classes. The graded data were joined to the census output area data and analyzed by overlapping the two data. As a result of analysis of 17 residential areas in 5 small and medium cities in Jeollanam-do, 4 types, 2 management models, and 4 indicators could be presented by grade and regional characteristics. This study is meaningful in that it is possible to plan regionally customized urban regeneration/maintenance management plans and projects through the typology of the current status and characteristics of the region, which is an important step in the bottom-up form.

• International conference on construction engineering and project management
• /
• 2009.05a
• /
• pp.1068-1074
• /
• 2009

The progress is widely used as a critical index for successful construction project management. In spite of the importance of progress measurement, the excessive management effort to collect and maintain detailed data has been highlighted as a major barrier to measurement of highly accurate progress. In order to reduce the required workload and to enhance accuracy, several researches have been conducted. These researches can be categorized into two groups. First group focuses on automated data collection utilizing advanced technologies only for limited construction tasks. The second group is a research area where the standard progress measurement methodologies encompassing entire construction tasks are investigated. Topics include the adjusting the level of details, standardizing work processes, and applying flexible WBS. However, the techniques for automated data collection are not fully investigated yet in the second group. Combining these two research areas can provide a solution for more effective progress management in terms of enhancing accuracy and optimizing workload. However, there has been no comprehensive research addressing these two research groups in an integrated manner. In this context, the purpose of this paper is to propose a methodology that identifies the most suitable measurement method and data acquisition technology (e.g., GPS, RFID, etc.) for entire construction tasks of a project. The proposed methodology in this paper will be able to facilitate the selection process of data acquisition technologies for entire construction tasks of a project and to support the overall enhancement of automated progress management.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.430-433
• /
• 2005

Laser bonding between similar and dissimilar thermoplastics has been investigated by making use of laser transmission weld technique. Spot welding of two layers of plastic materials has been demonstrated by using of a high-quality diode-laser with 808nm wavelength. Weld areas increases according to power density, exposure time. The results of peel out test show that peel strengths increase with the area of molten plastics. Layers, which have the same chemical properties, have good bonding qualities. A bonding method which dye film is coated on the interface is used for laser bonding between plastics with high transmission for laser wavelength. Laser transmission bonding is worthy of attention because it is not in contact, requires a few tooling devices, allows a flexible energy delivery and produces nearly invisible welds

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.158-158
• /
• 2011

A wide range of techniques for the direct-printing of functional materials have been developed for the fabrication of micro- and nanoscale structures and devices. Here we report a new direct patterning method, liquid bridge-mediated nanotransfer molding (LB-nTM), for the formation of two- or three-dimensional structures with feature sized as small as tens of nanometers over large areas up to 4". LB-nTM is based on the direct transfer of various materials from a mold to a substrate via a liquid bridge between them. The LB-nTM method was applied to the preparation of organic nanowire FETs on flexible substrates.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.11a
• /
• pp.219-220
• /
• 2017

Current domestic waterproofing market in Korea mainly uses single-ply waterproofing materials comprised of coatings or waterproof sheets and two or more-ply composite waterproofing methods. In order to evaluate these types of composite waterproofing systems, a new test equipment and method that incorporates various deterioration conditions (joint displacement, chemical exposure, water pressure etc) was developed. In a comparison testing, the results showed that flexible type materials have higher response performance towards joint displacement than the hardened material. Furthermore, the importance of securing the stability of the waterproofing method in the vulnerable over-lap joint areas of waterproofing sheets is emphasized.