• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.14 no.1
• /
• pp.63-72
• /
• 2002

The main objective of this study is to propose a practical two-microphone impedance tube method to measure the sound transmission loss for flexible sound isolation sheets without the use of the time-consuming and expensive reverberation room. This method was based on the sound decomposition theory developed by Seybert using the spectral density functions of the incident and reflected sound waves. In order to verify the validity of the experimental results, the measured sound transmission losses from the proposed method were compared with the measured data from the reverberation room method and the calculated data from the theory satisfying the mass law of sound isolation material. The resulted trends of the sound transmission losses versus frequencies for several different sound isolation sheets were almost same for each other and agreed quite well in both methods except at some low frequency region. From the experimental results, it was found that the accuracy of sound isolation capability obtained by two-microphone impedance tube method depends upon the microphone spacing, the distance from the first microphone to the test sample surface and the test sample location.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.1
• /
• pp.91-99
• /
• 2004

Researches on the induced trench method using compressible materials such as clay, mud, straw have been performed to reduce the load acting on buried conduits under a high fill in USA and Canada. And in-situ tests on load reductionmethod using EPS block as a compressible inclusion have been performed in Japan and Norway. Using a EPS block as a compressible materials can have various benefits such as cost-effective design, enlargement of safety and easy construction of structure under high fills. This paper analyzes the arching material function of EPS which can result in reduction of earth pressure by arching effect in Corrugated Steel Pipe. A series of tests were conducted to evaluate the reduction of earth pressure on conduits using EPS. Based on field test it is found that the magnitude of vertical earth pressure on conduits was reduced to about 35∼40% compared with conventional flexible conduit systems.

• Journal of Environmental Science International
• /
• v.24 no.8
• /
• pp.1037-1043
• /
• 2015

Since single-use disposable plastic usage has steadily been increasing, recent trends in polymeric research point to increasing demand for eco-friend materials which reduce plastic waste. A huge amount of non-degradable polypropylene (PP)-based pots for seedling culture are discarded for transplantation. The purpose of this study is to investigate an eco-friendly biodegradable material as a possible substitute for PP pot. The blend of poly(lactic acid) (PLA) with poly(butylene adipate-co-terephthalate) (PBAT) was used because of its good mechanical and flexible properties as well as biodegradation. After landfill, various properties of the blend pot were investigated by UTM, SEM, NMR and TGA. The results showed the tensile strength of the blend film rapidly decreased after 5 weeks of landfill due to degradation. From NMR data after landfill, the composition of PLA in the blend was decreased. These results indicate that the biodegradation of the blend preferentially occurs in PLA component. To investigate the effect of holes in pot bottom and side on root growth, a plant in the pot was grown. Some roots came out through holes as landfill period increases. These results indicate that the eco-friendly pot can be directly planted without the removal of pot.

• Journal of Sensor Science and Technology
• /
• v.24 no.6
• /
• pp.373-378
• /
• 2015

The structure of the human ear is divided into the outer ear, the middle ear, and the inner ear. The inner ear includes the cochlea that plays a very important role in hearing. Recently, the development of an artificial cochlear device for the hearing impaired with cochlear damage has been actively researched. Research has been carried out on the biomimetic piezoelectric thin film ABM (Artificial Basilar Membrane) in particular. In an effort to improve the frequency separation performance of the existing piezoelectric thin film ABM, this paper presents the design, fabrication, and characterization of the production and performance of a partially etched-type ABM material. $O_2$ plasma etching equipment was used to partially etch a piezoelectric thin film ABM to make it more flexible. The mechanical-behavior characterization of the manufactured partially etched-type ABM showed that the overall separation frequency range shifted to a lower frequency range more suitable for audible frequency bandwidths and it displayed an improved frequency separation performance. In addition, the maximum magnitude of the vibration displacement at the first local resonant frequency was enhanced by three times from 38 nm to 112 nm. It is expected that the newly designed, partially etched-type ABM will improve the issue of cross-talk between nearby electrodes and that the manufactured partially etched-type ABM will be utilized for next-generation ABM research.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.3
• /
• pp.155-158
• /
• 2017

In this paper, ZnO Thin Film Transistors (TFTs) were fabricated by a sol-gel method using a low-temperature process, and their physical and electrical characteristics were analyzed. To lower the process temperature to $200^{\circ}C$, we used a zinc nitrate hydrate ($Zn(NO_3)_2{\cdot}xH_2O$) precursor. Thermo Gravimetric Analyzer (TGA) analysis showed that the zinc nitrate hydrate precursor solution had 1.5% residual organics, much less than the 6.5% of zinc acetate dihydrate at $200^{\circ}C$. In the sol-gel method, organic materials in the precursor disrupt formation of a high-quality film, and high-temperature annealing is needed to remove the organic residuals, which implies that, by using zinc nitrate hydrate, ZnO devices can be fabricated at a much lower temperature. Using an X-Ray Diffractometer (XRD) and an X-ray Photoelectron Spectrometer (XPS), $200^{\circ}C$ annealed ZnO film with zinc nitrate hydrate (ZnO (N)) was found to have an amorphous phase and much more oxygen vacancy ($V_o$) than Zn-O bonds. Despite no crystallinity, the ZnO (N) had conductance comparable to that of ZnO with zinc acetate dihydrate (ZnO (A)) annealed at $500^{\circ}C$ as in TFTs. These results show that sol-gel could be made a potent process for low-cost and flexible device applications by optimizing the precursors.

• International Journal of Highway Engineering
• /
• v.11 no.1
• /
• pp.187-194
• /
• 2009

This paper presents the development of transfer function accounting for cross-anisotropic behavior of aggregate base material for the pavement thickness design. The stress distributions predicted by nonlinear cross-anisotropic finite element program were realistic by eliminating excessive tensile stress at the bottom of the base layer and the critical pavement responses predicted by nonlinear cross-anisotropic model are higher than those predicted by linear or nonlinear isotropic models (Kim, 2004, Kim et at., 2005). Since the previously developed transfer functions such as Asphalt Institute and Chevron models, etc. were based on the critical responses obtained from linear isotropic model, those equations are not appropriate for the thickness design nonlinear cross-anisotropic base behavior. Therefore, the development of usable transfer functions for nonlinear cross-anisotropic model is ever more important. When the newly developed transfer functions were compared with AASHTO method for the thickness design, the newly developed transfer functions produce approximately 25mm reduced UAB thickness in AASHTO thickness design and this illustrates that linear isotropic model results in more conservative pavement design.

• The Journal of Advanced Prosthodontics
• /
• v.13 no.5
• /
• pp.281-291
• /
• 2021

PURPOSE. To evaluate the wear of computer-aided design/computer-aided manufacturing (CAD-CAM) dental ceramic materials opposed by enamel as a function of increased chewing forces. MATERIALS AND METHODS. The enamel cusps of healthy human third molar teeth (n = 40) opposed by materials from CAD-CAM dental ceramic groups (n = 10), including Vita Enamic^® (ENA), a polymer-infiltrated ceramic network (PICN); GC Cerasmart^® (CERA), a resin nanoceramic; Celtra^® Duo (DUO), a zirconia-reinforced lithium silicate (ZLS) ceramic; and IPS e.max ZirCAD (ZIR), a polycrystalline zirconia, were exposed to chewing simulation (1,200,000 cycles; 120 N load; 1 Hz frequency; 0.7 mm lateral and 2 mm vertical motion). The wear of both enamel cusps and materials was quantified using a 3D laser scanner, and the wear mechanisms were evaluated by scanning electron microscopy (SEM). The results were analysed using Welch ANOVA and Kruskal Wallis test (α = .05). RESULTS. ZIR showed lower volume loss (0.02 ± 0.01 mm³) than ENA, CERA and DUO (P = .001, P = .018 and P = .005, respectively). The wear of cusp/DUO [0.59 mm³ (0.50-1.63 mm³)] was higher than cusp/CERA [0.17 mm³ (0.04-0.41 mm³)] (P = .007). ZIR showed completely different wear mechanism in SEM. CONCLUSION. Composite structured materials such as PICN and ZLS ceramic exhibit more abrasive effect on opposing enamel due to their loss against wear, compared to uniform structured zirconia. The resin nano-ceramic causes the lowest enamel wear thanks to its flexible nano-ceramic microstructure. While zirconia appears to be an enamel-friendly material in wear volume loss, it can cause microstructural defects of enamel.

• Journal of the Regional Association of Architectural Institute of Korea
• /
• v.20 no.6
• /
• pp.41-46
• /
• 2018

The context of innovation in which we evolve today, subtracts us in a spacial reality and virtuality (digital) that aimed less and less to interact with natural processes which could converge to new possible relationships in the world. We constantly live in presence of fluctuations and imperceptible natural energies (wind, solar radiation, etc.) defined by flows, their own physicality, which remains without being virtual, elusive. This study first outlines how these energies already exploited within the framework of production, could be thought as interactive of our habitat's space dimension, as a prolongation of a physical and material environment built by men and for men, giving rise to new social, cultural dynamics, and making natural complexity of our space vivid, comprehensible with new visual and physical clues. In recent days, where lifestyles are changing, architecture no longer needs to limit its scope of creation to only built structures. Based on a deeper understanding of human and through new potential advanced technologies (kinetic system, etc), it is time to fundamentally diagnose what environments or devices contribute to our lives. Architecture becomes ${\ll}interface{\gg}$, step up its fundamental role, and newly defines the sturdy image and tectonics of existing environment, establishing a stance to search for a new typology. In the end, building will show two simultaneous and distinctive connections related to its physical existence: reality in its function and irreductibility, in its ability to forge new dynamic connections with its environment, hybridizing the spatial dimension to a new form of physicality, adaptive and incessantly flexible in the dimension time, becoming a vessel for ever changing contemporary lifestyles.

• Composites Research
• /
• v.32 no.4
• /
• pp.177-184
• /
• 2019

If what the mechanical properties according to a layer have was found out by analyzing the already fabricated composite, it could be possible to develop the composite of the better performance than the existing products. In this study, we tried to calculate the mechanical properties of the inner prepreg lamina by applying the reverse design technique to the composite structure made by laminating prepregs. When the physical quantities obtained by the simple tensile test are used alone and the physical quantities obtained by the tensile test and the mode analysis are used at the same time, the results of this study show that the accuracy of the latter is higher Finally, the maximum error of $E_1$ predicted was 0.09% and the maximum error of predicted $E_2$ was 7%.

• Journal of the Society of Naval Architects of Korea
• /
• v.58 no.4
• /
• pp.206-213
• /
• 2021

Recently, although the size of the LNG Cargo Containment System (CCS) has been increasing, the secondary barrier is reported to remain unchanged, and the conventional Flexible Secondary Barrier (FSB) used in Mark-III type has been pointed out to be vulnerable to failure owing to thermal and cyclic loads. In this respect, a tensile test was carried out to verify the reinforcing effect of FSB using aramid fiber on weft compared to the conventional FSB. In order to consider the LNG leakage situation, a series of tensile tests were conducted from ambient to cryogenic temperature, and mechanical properties were evaluated for each fiber direction on account of anisotropy. Tensile behavior and fracture analyses were performed to confirm the mechanical properties of each material according to temperature. Tensile test results proved that replacing the aramid fiber instead of E-glass fiber used on weft is effective in enhancing the mechanical properties.