• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제25회 추계학술대회논문집
• /
• pp.40-45
• /
• 2005

현재까지 적용되고 있는 추력제어 장치로는 크게 노즐의 확대부에 장착되어 화염의 방향을 조종하는 제트베인(jet vane), 제트탭(jet tab)방식과 노즐자체를 회전하는 방식인 볼/소켓형(ball & socket) 노즐, 플렉시블 씰형 (flexible seal)노즐로 구분된다. 본 연구는 노즐자체를 회전하여 추력방향을 제어하는 볼/소켓형(ball & socket) 노즐이 회전할 경우 발생되는 유입부의 비대칭성이 노즐 성능에 미치는 영향을 예측하기 위하여 수행한 3차원 수치해석결과와 공압시험 결과를 수록하였다. 유동해석 결과 유입부의 비대칭성이 유동에 미치는 영향은 노즐 목까지 점차적으로 줄어들고 하류 유동에 미치는 영향이 미비하였으며 해석된 주 추력의 크기는 시험에서 측정된 추력과 비슷한 경향을 나타내었으나 측 추력의 경우 시험 값보다 낮게 나타났다.

• 한국정밀공학회지
• /
• 제19권10호
• /
• pp.120-129
• /
• 2002

An integrated structure and controller design approach for rotating cantilever beam is presented. An optimization method is developed for improving positioning performance considering the elastic deformations during high speed rotation and adopting the beam shape and the control gains as design variables. For this end, a dynamic model is setup by the finite element method according to the shape of the beam. The mass and stiffness of the beam are distributed in such a way that the closed-loop poles of the control system should be located leftmost in the complex s-plane. For optimization method, the simulated annealing method is employed which has higher probability to find the global minimum than the gradient-based down-hill methods. Sequential design and simultaneous design methods are proposed to obtain the optimal shape and controller. Simulations are performed with new designs by the two methods to verify the effectiveness of the approach and the results show that the settling time is improved for point-to-point position controls.

• 한국항공우주학회지
• /
• 제44권7호
• /
• pp.562-567
• /
• 2016

비행속도와 조건에 따라 최적화된 형상을 갖는 모핑 날개는 작동기 기술, 구조 기계장치 기술, 유연 외피 재료, 제어법칙 기술 등 해결할 문제가 많다. 본 연구에서는 빠른 응답속도를 갖는 모핑 날개를 개발하기 위한 첫 단계로 형상기억합금 선을 작동기와 복원용 비틀림 스프링으로 구동되는 단일 플랩을 갖는 에어포일 설계하고 제작하였다. 제작된 모핑 에어포일의 작동실험을 통해 설계 개념의 타당성을 검증하였다. 실험을 통해 측정한 결과 원활한 작동과 매우 빠른 반응속도를 확인하였다.

• 한국지반환경공학회 논문집
• /
• 제10권4호
• /
• pp.41-48
• /
• 2009

표준사로 형성된 지반 10cm아래에 연성관을 매설하여 각각의 상대밀도에서 지반거동에 따른 관의 변형을 관찰을 하였다. 지반보강 상태에서의 관의 거동을 파악하기 위하여 지오그리드를 매설관 하부에 설치한 후 각각 지반에서의 관의 변형을 관찰하였다. 관아래 지오그리드를 설치한 후 보강된 지반의 관 변형형태를 관찰하였다. 지오그리드로 보강한 지반은 수직하중이 높아질수록 보강재에 인장력이 형성되어 보강유무에 따른 동일한 수직하중에서 침하가 감소하였다. 상대밀도 100%지반과 70%지반 변형분포가 차이가 나타났다. 보강 70%지반에서는 최종침하 100mm일 때 무보강 100%지반의 최종침하에서의 지반반력에 가깝게 수렴 하였다. 매설관의 하부 변형 형태에서도 무보강 100% 지반의 매설관 변형 형태와 유사한 것으로 보아 연약지반에서 지오그리드의 보강효과가 기대된다.

• 한국산업융합학회 논문집
• /
• 제21권4호
• /
• pp.183-189
• /
• 2018

The focus of this paper is to design and control a three fingered hand system with eight axes for smart factory with an flexible controller, and to keep a useful big database for dynamic manipulation based on the experimental results. The weight of the hand module is only 1.2 kg, but flexible motion and powerful grasping are possible. To achieve such a flexible motion control of a robotic hand, we have developed a robust and precise fingered hand with a control system incorporating image recognition system in which we deal with the problems of not only accuracy and range of motion but also the flexibility of hand. The fingers are arranged so as to grasp both circular and prismatic objects. In order to achieve the light mechanism, we reduced the number of joints and fingers as much as possible. In this study, it was used three fingers with eight axes which is the optimal number to achieve a robust grasping diverse shape parts for smart factory.

• 대한조선학회논문집
• /
• 제50권5호
• /
• pp.349-354
• /
• 2013

The blades of flexible propellers are formed by overlaying and adhering many layers of thin glass-fiber fabric sheets, are compressed and dried in the rigid mold. The current manufacturing process can not avoid the rather irregular deformation of the blades composed of non-isotropic non-uniform fabric structures, and inevitably introduces the different shape-forming errors between blades. In this paper, several flexible model propellers are precisely measured with three-dimensional optical instrument and compared with the original design geometry. The model propellers with the as-measured geometry are evaluated with the lifting-surface-theory-based propeller analysis code. The open-water performance are presented and discussed. The importance of the manufacturing accuracy is addressed to be able to apply the flexible propellers for propulsion of marine vehicles.

• 한국정밀공학회지
• /
• 제13권11호
• /
• pp.132-142
• /
• 1996

This paper presents a technique to model and control a manipulator which has a flexible link and moves in a vertical plane. The flexible link is modeled as an Euler-Bernoulli Beam. Elastic deformation of the flexible link is represented using the assumed modes method. A comparison function which satisfies all geometric and natural boundary conditions of a cantilever beam with an end mass is used as an assumed mode shape. Lagrange's equation is utilized for the development of a discretized model. This paper presents a simple technique to improve the correctness of the developed model. The final model including the shortening effect due to elastic deformation correlates very well with experimental results. The free body motion simulation shows that two assumed modes for the representation of the elastic deformation is proper in terms of the model size and correctness. A control algorithm is developed using PID control technique. The proportional, integral and derivative control gains are determined based on dominant pole placement method with a rigid one-link manipulator. A position control simulation shows that the control algorithm can be used to control the position and residual oscillation of the flexible one-link manipulator effectively.

• Journal of Mechanical Science and Technology
• /
• 제16권10호
• /
• pp.1222-1228
• /
• 2002

This research is the development of a flexible tactile sensor array for service robots using PVDF (polyvinylidene fluoride) film for the detection of a contact state in real time. The prototype of the tactile sensor which has 8${\times}$8 array using PVDF film was fabricated. In the fabrication procedure, the electrode patterns and the common electrode of the thin conductive tape were attached to both sides of the 281$\mu\textrm{m}$ thickness PVDF film using conductive adhesive. The sensor was covered with polyester film for insulation and attached to the rubber base for a stable structure. The proposed fabrication method is simple and easy to make the sensor. The sensor has the advantages in the implementing for practical applications because its structure is flexible and the shape of the each tactile element can be designed arbitrarily. The signals of a contact force to the tactile sensor were sensed and processed in the DSP system in which the signals are digitized and filtered. Finally, the signals were integrated for taking the force profile. The processed signals of the output of the sensor were visualized in a personal computer, and the shape and force distribution of the contact object were obtained. The reasonable performance for the detection of the contact state was verified through the sensing examples.

• 소성∙가공
• /
• 제25권1호
• /
• pp.12-20
• /
• 2016

Press machines and dies are commonly used for 3D curved sheet forming. Using conventional die forming can cause economic problems since various modifications of the die shape are required depending on the product shape. Various types of flexible forming such as multi-point dieless forming (MDF), flexible incremental roll forming have been developed to improve the needed process flexibility. Although MDF can reduce the production cost using reconfigurable dies, it still has significant material loss. Drawbacks such as wrinkling, dimpling, and forming errors can also occur despite continuous investigations to mitigate these defects. A novel sheet forming process for 3D curved surfaces, a flexibly-reconfigurable roll forming (FRRF), has been recently proposed to overcome the economic and technical limitations of current practice. FRRF has no limitation on blank size in the longitudinal direction, and also minimizes or eliminates forming defects such as wrinkling and dimpling. Feasibility studies of FRRF have been conducted using FE simulations for multi-curved shapes and various sheet thicknesses. Therefore, the fabrication of a FRRF apparatus is required for any follow-up studies. In the current study, experiments with reconfigurable rollers were conducted using a simple design pre-FRRF apparatus prior to fabricating the full size FRRF apparatus. There are three candidates for the reconfigurable roller: a bar-type shaft, a flexible shaft, a ground flexible shaft. Among these candidates, the suitable reconfigurable roller for FRRF is determined through various forming tests.

• 한국추진공학회지
• /
• 제10권2호
• /
• pp.46-52
• /
• 2006

현재까지 적용되고 있는 추력제어 장치로는 크게 노즐의 확대부에 장착되어 화염의 방향을 조종하는 제트베인(jet vane), 제트탭(jet tab)방식과 노즐자체를 회전하는 방식인 볼/소켓형(ball & socket) 노즐, 플렉시블 씰형 (flexible seal)노즐로 구분된다. 본 연구는 노즐자체를 회전하여 추력방향을 제어하는 볼/소켓형(ball & socket) 노즐이 회전할 경우 발생되는 유입부의 비대칭성이 노즐 성능에 미치는 영향을 예측하기 위하여 수행한 3차원 수치해석결과와 공압시험 결과를 수록하였다. 유동해석 결과 유입부의 비대칭성이 유동에 미치는 영향은 노즐 목을 지나면서 현저히 줄어들고 하류 유동에 미치는 영향이 미비하였으며 해석된 주 추력의 크기는 시험에서 측정된 추력과 비슷한 경향을 나타내었으나 측 추력의 경우 시험 값보다 낮게 나타났다. 또한 시험의 결과 기하학적으로 회전된 회전각에 의한 추력방향과 측정된 추력의 방향이 일치하지 않음을 알 수 있었다.