• 한국전산구조공학회논문집
• /
• 제29권1호
• /
• pp.37-44
• /
• 2016

본 연구는 2.5MW급 풍력발전기용 기어박스의 동특성 분석에 관한 것으로서, 유연핀(flexible pin) 채용에 따른 유성기어축의 미스얼라인먼트(misalignment) 개선여부와 충격하중에 따른 기어박스의 동응답 특성을 유한요소해석을 통해 고찰하였다. 내부의 복잡한 기어시스템의 하중전달을 정확하게 그리고 효과적으로 반영하기 위해 치접촉을 등가 치강성계수를 갖는 스프링요소와 물림률을 이용하여 모델링하였다. 기어의 등가 치강성계수는 기어치에 대한 변형해석을 통해 계산하였으며, 동특성 분석을 위해 기어박스 입력단에 충격 토오크를 부과하였다. 수치실험을 통해 등가 치강성모델의 타당성을 검증하였으며, 양단 그리고 일단 고정축과의 상대 비교를 통해 유연핀 적용에 따른 유성기어축의 미스얼라인먼트 개선여부를 확인할 수 있었다.

• Tribology and Lubricants
• /
• 제16권1호
• /
• pp.39-45
• /
• 2000

In this paper, the effects of shaft and bearing flexibilities are investigated for the accurate modeling of a shaft-bearing system supported by ball bearings. Generally, rolling bearings are modeled by simple rigid pin-joint in the mechanical design. However, they can no longer be modeled by ideal boundary conditions in the advanced applications because the rigid pin-joint model cannot satisfy the current trends of mechanical design decreasing mass and reducing volume. Consequently the flexible support model of ball bearing is investigated using the static analysis module developed by A .B. Jones and T. A. Harris. A simple two-bearing system, supported by two deep groove ball bearings and radially loaded on the shaft midway between the bearings, is utilized to validate the coupled model of shaft-bearing system. Numerical computations using the model indicate that the shaft span length, locating/floating bearing arrangements and applied bearing size are significant factors in determining the mechanical behaviors. The flexible support model of ball bearing can be escaped to over-estimate in the bearing fatigue life. The proposed simple design formulation obtained by numerical simulations can approximately predict a rate of bearing life reduction as a function of shaft span length/shaft diameter (L/d).

• Journal of Communications and Networks
• /
• 제13권1호
• /
• pp.70-76
• /
• 2011

This paper presents the unified user equipment (UE) baseband modulation and demodulation (modem) hardware platform architecture to support multiple radio access technologies. In particular, this platform selectively supports two systems; one is HEDGE system, which is the combination of third generation partnership project (3GPP) Release 7 high speed packet access evolution (HSPA+) and global system for mobile communication (GSM)/general packet radio service (GPRS)/enhanced data rates for GSM evolution (EDGE), while the other is LEDGE system, which is the combination of 3GPP Release 8 long term evolution (LTE) and GSM/GPRS/EDGE. This is done by applying the flexible pin multiplexing scheme to a hardwired pin mapping process. On the other hand, to provide stable connection, high portability, and high debugging ability, the stacking structure is employed. Here, a layered board architecture grouped by functional classifications is applied instead of the conventional one flatten board. Based on this proposed configuration, we provide a framework for the verification step in wireless cellular communications. Also, modem function/scenario test and inter-operability test with various base station equipments are verified by system requirements and scenarios.

• 소성∙가공
• /
• 제33권2호
• /
• pp.112-117
• /
• 2024

In this study, the friction and wear characteristics of Inconel 600 in the superplastic forming process of Ti6Al4V were evaluated through pin-on-disc tests. To achieve an efficient and systematic experimental design, the Taguchi method was employed. The wear track of the Inconel 600 pin showed scratches in the sliding contact direction, confirming that the wear mechanism is abrasive wear. Through sensitivity analysis such as ANOVA and Main effects, it was confirmed that both normal force and sliding distance have a significant impact on the wear. Changes in sliding velocity and distance did not affect the friction coefficient, which remained relatively constant at approximately 0.380. The wear prediction model for Inconel 600 in the superplastic forming of Ti6Al4V was constructed, which can be utilized as a guideline for the prediction and management of tool wear.

• 한국임상수의학회지
• /
• 제39권4호
• /
• pp.156-161
• /
• 2022

The objective of the present study was to assess the prevalence, occurrence pattern, and clinical outcomes of transfixation pinning and casting (TPC) for fractures in Korean native calves, and to identify the advantages of the procedure. The study investigated 52 cases of bone fractures documented from January 2017 to December 2020. Hindlimb fractures (72%) were the most common in bone fractures (n = 50). The distribution of fractures was highest in the tibia (n = 15), followed by the metatarsal (n = 12), femur (n = 9), radius/ulna (n = 8), metacarpal (n = 3), humerus (n = 3), mandible (n = 1), and caudal vertebrae (n = 1). All cases were diagnosed via radiographic evaluation. Closed fractures (86%) were the most common, followed by open fractures (14%). Surgery was performed on 34 calves using intramedullary pin (IM pin), TPC, cross pin, flexible wire (F-wire), and/or plate fixation. The rest of the calves were treated with external coaptation (n = 12) or were not treated (n = 6). Subsequently, 24 calves with follow-up records were evaluated in the bone fracture cases (n = 50). Bone union was observed in 15 (62%) calves; 3 (12%) calves showed non-union; 4 (16%) calves were dead after surgery; and 2 (8%) calves were euthanized at the owner's request. Among the 24 follow-up surgery cases, the most successful cases were tibia fractures (75%) surgically treated using TPC and/or IM pin. These findings suggest that TPC surgery is effective in the management of fractures in Korean native calves.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.249-249
• /
• 2012

최근 주목받고 있는 Flexible Organic Light Emitting Diode (OLED) display에서는 Flexible 특성이 요구된다. 이는 현재 쓰이는 유리기판 대신 플라스틱기판으로 만들어야 가능하다. 하지만 플라스틱기판은 구성물질로 유기물을 사용하므로 수분과 산소의 투과에 매우 취약하다. 이는 장시간 사용 시 기판 위에 제작된 소자성능저하를 야기하는 등의 소자 신뢰도에 치명적 결함을 갖게 하는 원인이 된다. 따라서 기판 위의 소자를 보호할 수 있는 봉지기술 개발이 필요한데 가장 잘 알려진 플라스틱 기판에 적합한 Barrier기술로 유기물과 무기물을 교대로 적층하는 기술[1] 등이 있다. 본 연구에서는 PE-CVD 공정기술을 이용한 Flowable Oxide 박막과 ALD 공정기술을 이용한 Al2O3 무기물 박막을 적층하여 봉지박막을 구성하려 한다. Flowable Oxide는 저온공정이 가능하며 높은 증착속도와 뛰어난 Gap fill 특성을 가지고 있는데 이는 플라스틱기판의 엉성한 분자구조를 치밀하게 만들 것으로 예상되며 표면의 Pin-hole 또한 쉽게 채우는 특성이 있다. 실험은 Polyethylene Naphthalate (PEN) film 위에 PE-CVD 공정을 이용하여 Flowable Oxide를 증착하고, 그 후에 ALD 공정을 이용하여 Al2O3을 적층한 것을 하나의 샘플로 하였다. 샘플의 분석은 Ca test를 이용한 Water Vapor Transmission rate(WVTR)과 FT-IR, FE-SEM을 이용하여 분석하였다. FT-IR로 박막의 구성요소를 확인 하고 FE-SEM으로 박막의 Cross section image를 얻을 수 있었으며 또한 $4.85{\times}10^{-5}g/m^2$ day의 초기 WVTR 값을 얻을 수 있었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.401-402
• /
• 2007

The preparation and characteristics of ITO anode films grown using a linear facing target sputtering (FTS) technique for use in organic light emitting diodes (OLED) and flexible OLED is described. The electrical, optical, and work function of the ITO anode, which was prepared by linear FTS at room temperature, were comparable to those of commercial ITO anode films. In particular, linear FTS-grown ITO films shows very smooth surface without defects such as pin hole and cracks due to low substrate temperature. Furthermore OLED with the linear FTS-grown ITO anode film shows comparable electrical and optical properties to those of OLED with the commercial crystalline-ITO anode film. This suggested that linear FTS is promising thin film technology for preparing high quality anode film in OLEDs and flexible OLEDs.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2017년도 춘계학술대회 논문집
• /
• pp.114.2-114.2
• /
• 2017

Transparent film heaters (TFHs) based on Joule heating are currently an active research area. However, TFHs based on an indium tin oxide (ITO) monolayer have a number of problems. For example, heating is concentrated in part of the device. Also, heating efficiency is low because it has high sheet resistance ($R_S$). Resistance of indium zinc oxide (IZO) is similar to ITO and it can be used to flexible applications due to its amorphous structure. To solve these problems, our study introduced hybrid layers of IZO/Ag/IZO deposited by magnetron sputtering, and the electrical, optical, and thermal properties were estimated for various thickness of the metal interlayer. It was found that the sheet resistance of the multilayer was mainly dependent on the thickness of the Ag layers. The $R_S$ of IZO(40)/Ag/IZO(40nm) multilayer was 5.33, 3.29, $2.15{\Omega}/{\Box}$ for Ag thickness of 10, 15, and 20nm, respectively, while the $R_S$ of an IZO monolayer(95nm) was $59.58{\Omega}/{\Box}$. The optical transmittance at 550nm for the IZO(95nm) monolayer is 81.6%, and for the IZO(40)/Ag/IZO(40nm) multilayers with Ag thickness 10, 15 and 20nm, is for 72.8, 78.6, and 63.9%, respectively. The defrost test showed that the film with the lowest RS had the highest heat generation rate (HGR) for the same applied voltage. The results indicated that IZO(40)/Ag(15)/IZO(40nm) multilayer has the best suitable property, which is a promising thin film heater for the application in vehicle windshield.

• Nuclear Engineering and Technology
• /
• 제55권2호
• /
• pp.756-768
• /
• 2023

Neutron transport calculations are extremely challenging due to the high computational cost of large and complex problems. A multilevel octree grid algorithm (MLTG) of discrete ordinates method was developed to improve the modeling accuracy and simulation efficiency on 3-D Cartesian grids. The Balakovo-3 VVER-1000 neutron dosimetry benchmark is calculated to verify and validate this numerical technique. A simplified S₂ synthetic acceleration is used in the MLTG calculation method to improve the convergence of the source iterations. For the triangularly arranged fuel pins, we adopt a source projection algorithm to generate pin-by-pin source distributions of hexagonal assemblies. MLTG provides accurate geometric modeling and flexible fixed source description at a lower cost than traditional Cartesian grids. The total number of meshes is reduced to 1.9 million from the initial 9.5 million for the Balakovo-3 model. The numerical comparisons show that the MLTG results are in satisfactory agreement with the conventional S_N method and experimental data, within the root-mean-square errors of about 4% and 10%, respectively. Compared to uniform fine meshing, approximately 70% of the computational cost can be saved using the MLTG algorithm for the Balakovo-3 computational model.

• Journal of Advanced Marine Engineering and Technology
• /
• 제34권5호
• /
• pp.711-717
• /
• 2010

본 논문에서는 플라스틱 평판에 핀 홀을 생성하여 문자나 이미지를 표현하는 디스플레이 보드를 자동으로 제작하는 펀칭시스템을 개발하였다. 핀 홀을 생성한 평판은 가장자리에 설치한 다양한 색상의 발광다이오드 빛을 반사하여 미려한 디스플레이 보드에 사용된다. 펀칭시스템은 정밀한 위치 및 깊이 생성을 위해 총 4개의 엑추에이터를 사용하였다. 디스플레이 보드 상의 글자나 이미지의 반사효과와 빠른 생산성을 위하여 정밀한 구동 기구부를 개발하고 PID 제어 알고리즘을 적용하였다. 그리고 사용자가 반사되는 글자의 모양이나 이미지를 구성하는데 도움을 줄 수 있는 GUI 프로그램과 PC기반의 제어시스템을 구성하였다. 또한 펀칭속도와 생성된 핀 홀의 깊이를 검사하여 본 시스템의 성능을 검증하였다.