• 소성∙가공
• /
• 제21권8호
• /
• pp.499-505
• /
• 2012

The fuel cell is a very promising power generation system combining the benefits of extremely low emissions, high efficiency, ease of maintenance and durability. In order to promote the commercialization of fuel cells, a flexible forming process, in which a hyper-elastic rubber is adopted as a medium to transmit forming pressure, is suggested as an efficient and cost effective manufacturing method for fuel cell bipolar plates. In this study, the ability of this flexible forming process to produce the micro channel arrays on metallic bipolar plates was first demonstrated experimentally. Then, a finite element (FE) model was built and validated through comparisons between simulated and experimental results. The effects of key process parameters on the forming performance such as applied load and punch velocity were investigated. As a result, appropriate process parameter values allowing high dimensional accuracy without failure were suggested.

• Journal of Welding and Joining
• /
• 제31권5호
• /
• pp.59-63
• /
• 2013

A bendable electronic module has been developed for a mobile application by using a low-cost roll-to-roll manufacturing process. In flexible embedded electronic module, a thin silicon chip was embedded in a polymer-based encapsulating adhesive between flexible copper clad polyimide layers. To confirm reliability and durability of prototype bendable module, the following tests were conducted: Moisture sensitivity level, thermal shock test, high temperature & high humidity storage test, and pressure cooker tester. Those experiments to induce failure of the module due to temperature variations and moisture are the experiment to verify the reliability. Failure criterion was 20% increase in bump resistance from the initial value. The mechanism of the increase of the bump resistance was analyzed by using non-destructive X-ray analysis and scanning acoustic microscopy. During the pressure cooker test (PCT), delamination occurred at the various interfaces of the bendable embedded modules. To investigate the failure mechanism, moisture diffusion analysis was conducted to the pressure cooker's test. The hygroscopic characteristics of the encapsulating polymeric materials were experimentally determined. Analysis results have shown moisture saturation process of flexible module under high temperature/high humidity and high atmosphere conditions. Based on these results, stress factor and failure mechanism/mode of bendable embedded electronic module were obtained.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2009년도 9th International Meeting on Information Display
• /
• pp.131-134
• /
• 2009

We have developed a flexible OTFT backplane in which all the dielectrics are formed by solutionprocess in order to achieve low-cost and highthroughput manufacturing. The backplane successfully drives a flexible AM-OLED display with peak brightness of > 200 nit and the contrast ratio of > 1000:1 with great mechanical flexibility.

• 한국염색가공학회지
• /
• 제35권3호
• /
• pp.179-187
• /
• 2023

In this study, we developed a microfiber-based flexible pressure sensor with high sensitivity and excellent skin breathability. A nonwoven fabric composed of microfibers was prepared by electrospinning, which resulted in excellent moisture permeability of the sensor (143 g∙m^-2∙h^-1). In particular, high-pressure sensitivity (0.36 kPa^-1) was achieved by introducing submicron structures on the microfiber surface by controlling the ambient humidity during electrospinning. The fabrication technology of the microfiber-based flexible pressure sensors reported in this study is expected to contribute to the commercialization of flexible pressure sensors applicable to long-term wearable health monitoring as well as virtual/augmented reality and electronic skin applications.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.1177-1181
• /
• 1995

Fixtures are devided into special purpose fixtures, modular fixtures and general purpose fixtures. In this paper, the database of modual fixtures for flexible manufacturing systems is estabilished. Modular fixtures are classified into base plates, supporting elements, locating elements, clamping elements and accessories. Also the concept for the modular fixture design expert system is proposed.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1994년도 Proceedings of the Korea Automatic Control Conference, 9th (KACC) ; Taejeon, Korea; 17-20 Oct. 1994
• /
• pp.676-680
• /
• 1994

Three synchronic variables (Deviation Time, Fairness Time, Synchronic Time) are defined for Timed Place Petri Nets (TPPN). These parameters show the dependency between the firing of transition subsets in the time domain by different values. The approaches in this paper can be used to find synchronic relations in Stochastic Petri Nets. This paper presents how to decide the minimum resources required to a Flexible Manufacturing Cell using Synchronic Time concept.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1991년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 22-24 Oct. 1991
• /
• pp.488-492
• /
• 1991

This paper deals with modeling and scheduling for flexible manufacturing systems(FMS). In modeling extended Petri nets are used to describe various and complex properties. To resolve multiple conflict without predefined properties, such as part selection, machine selection, rule-based scheduling method is introduced. This structure have a capability of on-line scheduling with systematic modeling description.

• 한국경영과학회:학술대회논문집
• /
• 대한산업공학회/한국경영과학회 1992년도 춘계공동학술대회 발표논문 및 초록집; 울산대학교, 울산; 01월 02일 May 1992
• /
• pp.159-168
• /
• 1992

생산라인의 line balancing이 흐름생산에 있어서 일관된 생산을 하기 위한 필수조건이다. 여러 다양한 제품을 생산하는 printed circuit board(PCB) 공장에서의 line balancing을 얻기 위해서는 mixed model line balancing절차를 설명하고자 한다.

• 산업경영시스템학회지
• /
• 제15권26호
• /
• pp.165-172
• /
• 1992

This paper develops the at location system of milling cutting tools to be used on NC milling machine tool by the technique of cluster analysis. The implementation concerning the tool management system will be applying to Flexible Manufacturing System efficiently.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1992년도 춘계학술대회 논문집
• /
• pp.262-267
• /
• 1992

본 논문에서는 국내 중소기업을 위한 기술지원의 일환으로 시범적으로 개발한 자동화 모델을 소개한다. 개발된 모델은 자동차에 사용되는 오일 펌프 드리이브용 기어를 대상부품으로한 FMC(Flexible Manufacturing Cell)로서 선삭과 치절( Hobbing)공정을 자동화 하는 2 Set의 FMC로 구성되어있다. FMC 개발을 위하여 대상부품 특성과 공정을 분석하였으며 개발된 시스템의 구성 및 개별장비에 대한 기능에 대해 기술하였다.