• Journal of the Korean GEO-environmental Society
• /
• v.7 no.5
• /
• pp.57-66
• /
• 2006

In this study, the centrifuge model tests were carried out to evaluate the stress concentration ratio, the deformation modes of piles and the ground movement in clay deposit improved by SCP and GCP piles with changing the replacement ratio(20%, 40%, 60%) under flexible loading. Based on the results obtained, it was shown that the stresses acting on GCP was larger than those acting on SCP with the same replacement ratio. It was evaluated that the average stress concentration ratio of soft clay ground improved by GCP was slightly larger than that of SCP when the replacement ratio is 40%. Only expansion failure occurred in GCP, whereas SCP showed the expansion and shear failure simultaneously.

• 한국방재학회:학술대회논문집
• /
• 2008.02a
• /
• pp.329-332
• /
• 2008

This study presents a viscoelastic characterization of flexible pavement subjected to moving loads. A series of field tests have been conducted on three pavement sections (A2, A5, and A8) at the Korea Expressway Corporation (KEC) test road. The effect of vehicle speed on the responses of each test section was investigated at three speeds: 25km/hr, 50km/hr, and 80km/hr. During the test, both longitudinal and lateral strains were measured at the bottom of asphalt layers and in-situ measurements were compared with the results of finite element (FE) analyses. A commercial FE package was used to model each test section and a step loading approximation has been adopted to simulate the effect a moving vehicle. Field responses reveal the strain anisotropy (i.e., discrepancy between longitudinal and lateral strains) and the amplitude of strain normally decreases as the vehicle speed increases. In most cases, lateral strain was smaller than the longitudinal strain, and strain reduction was more significant in lateral direction.

• Journal of the Korean institute of surface engineering
• /
• v.49 no.3
• /
• pp.252-259
• /
• 2016

In order to form an aluminum-doped zinc oxide (AZO) transparent electrode film on a polyethylene terephthalate (PET) substrate used for a flexible display substrate, the AZO transparent electrode was produced at low temperature without substrate heating. Even though the produced electrode showed characteristic optical transmittance of 90 % (at 550 nm) and sheet resistance within $100{\Omega}/sq$, cracks occurred 10 minutes after loading applied 2 mm radius of curvature, and the sheet resistance increased linearly. An insertion layer of ZrCu was formed between the AZO film and the PET substrate to suppress the generation of cracks on the AZO film. It was verified that the crack was not generated 30 minutes after the loading of 2 mm radius of curvature, and no increase in sheet resistance was recorded. There was also not cracks in the dynamic bending test of 4 mm radius, but surface resistance was slightly increased. As a result, the ZrCu insertion film improved the interfacial adhesion between the substrate and AZO film layer without increasing sheet resistance and decreasing transmittance.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.1
• /
• pp.48-54
• /
• 2004

Generally, structural optimization is carried out based on external static loads. All forces have dynamic characteristics in the real world. Mathematical optimization with dynamic loads is extremely difficult in a large-scale problem due to the behaviors in the time domain. In practical applications, it is customary to transform the dynamic loads into static loads by dynamic factors, design codes, and etc. But the optimization results with the unreasonably transformed loads cannot give us good solutions. Recently, a systematic transformation has been proposed as an engineering algorithm. Equivalent static loads are made to generate the same displacement field as the one from dynamic loads at each time step of dynamic analysis. Thus, many load cases are used as the multiple loading conditions which are not costly to include in modem structural optimization. In this research, the proposed algorithm is applied to the optimization of flexible multibody dynamic systems. The equivalent static load is derived from the equations of motion of a flexible multibody dynamic system. A few examples that have been solved before are solved to be compared with the results from the proposed algorithm.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.10
• /
• pp.24-31
• /
• 2006

In this paper, mechanical behavior of unidirectional composites with flexible matrix was predicted by geometrical non-linear finite element analysis. Two typical idealized unit cells of square and hexagonal fiber arrays were modeled and these were subjected to different loadings. The stress-strain behavior of composites was predicted from which the effective properties were calculated. The hyperelasticity of polyurethane matrix was considered using Mooney-Rivlin model. In result, the stress-strain behavior of flexible composites shows non-linearity, especially it is remarkable under transverse normal and shear loading conditions. In this cases, there are great difference between square and hexagonal fiber array models.

• International Journal of Highway Engineering
• /
• v.17 no.1
• /
• pp.69-75
• /
• 2015

PURPOSES : The objective of this study is to evaluate the effectiveness of a geogrid reinforced subbase of permeable flexible pavement structures with respect to permanent deformation. METHODS : Experimental trials employing a repeated triaxial load test scheme were conducted for both a geogrid reinforced subbase material and a control specimen to obtain the permanent deformation properties based on the VESYS model. Along with this, a finite element-based numerical analysis was conducted to predict pavement performance with respect to the rutting model incorporated into the analysis. RESULTSAND CONCLUSIONS : The results of the experimental study reveal that the geogrid reinforcement seems to be effective in mitigating permanent deformation of the subbase material. The permanent deformation was mostly achieved in the early stages of loading and then rapidly reached equilibrium as the number of load applications increased. The ultimate permanent deformation due to the geogrid reinforcement was about 1.5 times less than that of the control specimen. Numerical analysis showed that the permeable, flexible pavement structure with the geogrid reinforced subbase also exhibits less development of rutting throughout the service life. This reduction in rutting led to a 20% decrease in thickness of the subbase layer, which might be beneficial to reduce construction costs unless the structural adequacy is not ensured. In the near future, further verification must be conducted, both experimentally and numerically, to support these findings.

• The KSFM Journal of Fluid Machinery
• /
• v.10 no.5
• /
• pp.46-53
• /
• 2007

Stem friction coefficient and valve factor are very important parameters for the evaluation of valve performance. In this study, the characteristics of stem friction coefficient and valve factor are analyzed, and thor bounding value is determined. The hydraulic testing is performed for many flexible wedge gate valves in the plant and statistical method is applied to the determination of bounding value. According to the results of this study, stem friction coefficient does not change much with differential pressure, and the bounding value of closing stroke is higher than that of opening stroke. The valve factor of valves with high differential pressure is higher than that of valves with medium differential pressure. It means valve factor is more sensitive to the differential pressure than the stem friction coefficient. Valve factor of the closing stroke is higher than that of opening stroke due to piston effect.

• Steel and Composite Structures
• /
• v.19 no.6
• /
• pp.1333-1354
• /
• 2015

A higher order analytical solution for static analysis of a truncated conical composite sandwich panel subjected to different loading conditions was presented in this paper which was based on a new improved higher order sandwich panel theory. Bending analysis of sandwich structures with flexible cores subjected to concentrated load, uniform distributed load on a patch, harmonic and uniform distributed loads on the top and/or bottom face sheet of the sandwich structure was also investigated. For the first time, bending analysis of truncated conical composite sandwich panels with flexible cores was performed. The governing equations were derived by principle of minimum potential energy. The first order shear deformation theory was used for the composite face sheets and for the core while assuming a polynomial description of the displacement fields. Also, the in-plane hoop stresses of the core were considered. In order to assure accuracy of the present formulations, convergence of the results was examined. Effects of types of boundary conditions, types of applied loads, conical angles and fiber angles on bending analysis of truncated conical composite sandwich panels were studied. As, there is no research on higher order bending analysis of conical sandwich panels with flexible cores, the results were validated by ABAQUS FE code. The present approach can be linked with the standard optimization programs and it can be used in the iteration process of the structural optimization. The proposed approach facilitates investigation of the effect of physical and geometrical parameters on the bending response of sandwich composite structures.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.19 no.2
• /
• pp.40-51
• /
• 2015

In reinforced concrete structure, rebar connection method should be considered because of its structural role to resist the tensile stress and its structural load transmission with concrete in the concrete structure. Lapped splice and mechanical sleeve type connector have been traditionally used to connect rebar in the concrete structures. In this study, to examine the mechanical and failure behaviors of rebar bar connected by taper type coupler in the concrete member depending on connection type and condition, tensile tests of steel rebar with taper type coupler and flexible loading tests of concrete beams were conducted. Its tensile strength and flexible strength of the rebar connected by taper type coupler were compared and evaluated by mechanical behaviors of rebar. From this study, steel rebar connected by taper type coupler showed it has similar mechanical performance comparing with unconnected rebar, thus taper type coupler can be used in the rebar fabrication of reinforced concrete structure.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.10
• /
• pp.1108-1120
• /
• 1990

The present study is to develop an intelligent control system for flexible manufacturing system, which is suitable for a variety of manufacturing types with smaller production rates. The controller is designed to integrate heuristic rules with optimization techniques for loading as well as flow rate of parts and ultimately meeting performance indices. The control function implemented by an optimization technique is to calculate short term production rates of parts. The heuristic control determined by production rules requires knowledge base to evaluate selected loading alternatives according to short term production rate and current process information, and also to determine final decision pertaining to loading. In this case, the knowledge base is constructed using the rules for evaluating alternatives, decision criteria, and flow control of parts in manufacturing system. The database is formulated by means of managing and updating current process information. A graphic system to monitor current status of the function and operation of manufacturing system is developed, and computer simulation is carried out to evaluate the performance of the proposed controller.