• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.6-6
• /
• 2010

Indium Tin Oxide (ITO)를 포함한 Transparent Conduction Oxide (TCO)는 LCD, OLED와 같은 Display, 그리고 Solar Cell 등 광신호와 전기신호간 변환이 필요한 모든 Device에 반드시 필요한 핵심 물질로, 특히 고특성 Display의 투명전극에서 요청되는 95% 이상의 투과도와 $15\;{\Omega}/{\square}$ 이하의 면저항 특성을 동시에 만족할 수 있는 기술은 현재까지 Plasma Sputtering 공정으로 $160^{\circ}C$ 이상에서 증착된 ITO 박막이 유일하다. 그러나, 최근 차세대 기술로서 Plastic Film을 기반으로 하는 Flexible Display 및 Flexible Solar Cell 구현에 대한 요구가 급증하면서, Plastic Film 기판위에 Plasma Damage이 없이 상온에 가까운 저온 ($100^{\circ}C$ 이하)에서 특성이 우수한 ITO 투명전극을 형성 할 수 있는 기술의 확보가 중요한 현안이 되고 있다. 지난 10년 동안 $100^{\circ}C$이하 저온에서 고특성의 ITO 또는 TCO 박막을 얻기위한 다양한 연구와 구체적인 공정이 활발히 연구되어 왔으나, ITO의 결정화 온도 (통상 $150{\sim}180^{\circ}C$)이하에서 증착된 ITO박막은 비정질 상태의 물성적 특성을 보여 원하는 전기적, 광학적 특성확보가 어려웠다. 본 논문에선 기본적으로 절연체 특성을 가져야 하는 산화물인 TCO가 반도체 또는 도체의 물리적 특성을 보여주는 기본원리의 고찰을 토대로, 재료학적 특성상 Crystalline 구조를 보여야 하는 ITO (Complex Cubic Bixbyte Structure)가 Plasma Sputtering 공정으로 저온에서 증착될 때 비정질 구조를 갖게 되는 원인을 규명하고, 이를 바탕으로 저온에서 증착된 ITO가 Crystalline 구조를 유지 할 수 있게 하고, Stress Control에 유리한 Nano-Crystalline 박막을 형성하면서 Crystallinity를 임의로 조절 할 수 있는 새로운 기술인 Magnetic Field Shielding Sputtering (MFSS) 공정과 최근 성과를 소개한다. 한편, 또 다른 새로운 저온 TCO 박막형성 기술로서, 유기반도체와 같은 Process Damage에 매우 취약한 유기물 위에 Plasma Damage 없이 TCO 박막을 직접 형성할 수 있는 Neutral Beam Assisted Sputtering (NBAS) 기술의 원리를 설명하고, 본 공정을 적용한 Top Emission OLED 소자의 결과를 소개한다. 또한, 고온공정이 수반되는 Solar Cell용 투명전극의 경우, 통상의 TCO박막이 고온공정을 거치면서 전기적 특성이 열화되는 원인을 규명하고, 이에 대한 근본적 해결 방법으로 ITO 박막의 Dopant인 Tin (Sn) 원자의 활성화를 증가시킨 Inductively Coupled Plasma Assisted DC Magnetron Sputtering (ICPDMS)의 원리와 박막의 물성적 특성과 내열 특성을 소개한다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2010년도 제39회 하계학술대회 초록집
• /
• pp.167-167
• /
• 2010

Indium tin oxide (ITO) has been widely used as transparent conductive oxides (TCOs) for transparent electrodes of various optoelectronic devices, such as liquid crystal displays (LCD) and organic light emitting diodes (OLED). However, indium has become increasingly expensive and rare because of its limited resources. In addition, ITO thin films have some problems for OLED and flexible displays, such as imperfect work function, chemical instability, and high deposition temperature. Therefore, multi-component TCO materials have been reported as anode materials. Among the various materials, IZTO thin films have been gained much attention as anode materials due to their high work function, good conductivity, high transparency and low deposition temperature. IZTO thin films with a thickness of 200nm were deposited on Corning glass substrate at different substrate temperature by pulsed DC magnetron sputtering with a sintered ceramic target of IZTO (In2O3 70 wt%, ZnO 15 wt%, SnO2 15 wt%). We investigated the electrical, optical, structural properties of IZTO thin films. As the substrate temperature is increased, the electrical properties of IZTO are improved. All IZTO thin films have good optical properties, which showed an average of transmittance over 80%. These IZTO thin films were used to fabricate organic light emitting diodes (OLEDs) as anode and the device performances studied. As a result, IZTO has utility value of TCO electrode although it reduced indium and we expect it is possible for the IZTO to apply to flexible display due to the low processing temperature.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.374-374
• /
• 2012

Nowadays, Active Matrix Organic Light-Emitting Diodes (AM-OLEDs) are the superior display device due to their vivid full color, perfect video capability, light weight, low driving power, and potential flexibility. One of the advantages of AM-OLED over Liquid Crystal Display (LCD) lies in its flexibility. The potential flexibility of AM-OLED is not fully explored due to its sensitivity to moisture and oxygen which are readily present in atmosphere, and there are no flexible encapsulation layers available to protect these. Therefore, we come up with a new concept of Inorganic-Organic hybrid thin film as the encapsulation layer. Our Inorganic layer is Al2O3 and Organic layer is F-Alucone. We deposited these layers in vacuum state using Atomic Layer Deposition (ALD) and Molecular Layer Deposition (MLD) techniques. We found the results are comparable to commercial requirement of 10-6 g/m2 day for Water Vapor Transmission Rate (WVTR). Using ALD and MLD, we can control the exact thin film thickness and fabricate more dense films than chemical or physical vapor deposition methods. Moreover, this hybrid encapsulation layer potentially has both the flexibility of organic layers and superior protection properties of inorganic layer.

• 한국전기전자재료학회논문지
• /
• 제20권9호
• /
• pp.798-801
• /
• 2007

Multilayer transparent electrodes, having a much lower electrical resistance than the widely used transparent conducting oxide electrodes, were prepared by using radio frequency magnetron sputtering. The multilayer structure consisted of five layers, indium tin oxided (ITO)/zinc oxide (ZnO)/Ag/zinc oxide (ZnO)/ITO. With about 50 nm thick ITO films, the multilayer showed a high optical transmittance in the visible range of the spectrum and had color neutrality. The electrical and optical properties of ITO/ZnO/Ag/ZnO/ITO multilayer were changed mainly by Ag film properties, which were affected by the deposition process of the upper layer. Especially ZnO layer was improved to adhesion of Ag and ITO. A high quality transparent electrode, having a resistance as low as and a high optical transmittance of 91% at 550 nm, was obtained. It could satisfy the requirement for the flexible OLED and LCD.

• 한국정밀공학회지
• /
• 제30권9호
• /
• pp.909-913
• /
• 2013

Various types of large substrate handling robots are used in the thin file solar cell manufacturing line as well as LCD or PDP production line. Because the robot handles the heavy substrate at high speed, there are some issues such as vibration control and the optimal design of arms and forks. As the substrate becomes larger and heavier, robot systems are also larger and the vibration issue of the robot end-effector becomes more important. In the paper, we established the robot modeling and the control architecture including the flexible part such as forks. Then, we performed dynamic simulation in the various condition and analyzed the characteristics of the fork vibration. We can reduce the vibration using the trajectory planning and input shaping algorithm and it was proved by experiment.

• 한국정밀공학회지
• /
• 제27권3호
• /
• pp.9-17
• /
• 2010

The FPCB is used for electronic products such as LCD display. The process of manufacturing FPCB includes a cutting process, in which each single FPCB is cut and separated from the panel where a series of FPCBs are arrayed. The most-widely used cutting method is the mechanical punching, which has the problem of creating burrs and cracks. In this paper, the cutting characteristics of the FPCB have been experimented using Nd:YAG DPSS UV laser as a way of solving this problem. To maximize the industrial application of this laser cutting process, test samples of the multilayered FPCB have been chosen as it is actually needed in industry. The cutting area of the FPCB has four different types of layer structure. First, to cut the test sample, the threshold laser cut-off fluence has been found. Various combinations of laser and process parameters have been made to supply the acquired laser cut-off fluence. The cutting characteristics in terms of the variation of the parameters are analyzed. The laser and process parameters are optimized, in order to maximize the cutting speed and to reach the best quality of the cutting area. The laser system for the process automation has been also developed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.19-20
• /
• 2006

As the Mobile and Display technology are being developed quickly, new wireless devices are released in great numbers. They reduce existing devices' life time and demand a reduction of developing period of portable devices. With these demands, existing film cutting mold used many films of portable devices, especially LCD Display, needs to be more precise, and cheaper. In this research, we have analyzed machining characteristics of cutter shapes, materials, and cutting conditions for application to other films. Cutter edge was machined by slot cutting method and CAD program to select the cutter shape and cutter angle. Also, we have determined the optimal cutting conditions using high speed machining experiments to improve the productivity.

• Transactions on Electrical and Electronic Materials
• /
• 제6권3호
• /
• pp.106-109
• /
• 2005

We have investigated the generation of pretilt angle for a nematic liquid crystal (NLC) alignment with in-situ photoalignment method on polyimide (PI) surfaces using polymer films. Especially, we studied in-situ photoalignment changing heating temperature from $50^{\circ}C\;to\;120^{\circ}C$ on the polymer film. The LC aligning capabilities and pretilt angle on the polymer substrates were better than those on the glass substrate using in-situ photoalignment method. It is considered that this increase in pretilt angle may be attributed to the roughness of the micro-groove substrate induced by the in-situ photoalignment. As temperature of heated subtrate and UV exposure time increase, pretilt angle of the cell used polymer film increased. It is considered that the heating temperature of substrate is attributed to generate pretilt angle. Also, electro-optical performances of the in-situ photoaligned TN cell using the polymer substrate are almost the same as that of the TN cell using the glass substrate.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2009년도 춘계학술발표대회
• /
• pp.15.2-15.2
• /
• 2009

Manufacturing of printed electronics using printing technology has begun to get into the hot issue in many ways due to the low cost effectiveness to existing semi-conductor process. This technology with both low cost and high productivity, can be applied in the production of organic thin film transistor (OTFT), solar cell, radio frequency identification (RFID) tag, printed battery, E-paper, touch screen panel, black matrix for liquid crystal display (LCD), flexible display, and so forth. The emerging technology to manufacture the products in mass production is roll-to-roll printing technology which is a manufacturing method by printings of multi-layered patterns composed of semi-conductive, dielectric and conductive layers. In contrary to the conventional printing machines in which printing precision is about $50~100{\mu}m$, the printing machines for printed electronics should have a precision under $30{\mu}m$. In general, in order to implement printed electronics, narrow width and gap printing, register of multi-layer printing by several printing units, and printing accuracy of under $30{\mu}m$ are all required. We developed the roll-to-roll printing equipment used for printed electronics, which is composed of un-winder, re-winder, tension measurement system, feeding units, dancer systems, guide unit, printing unit, vision system, dryer units, and various auxiliary devices. The equipment is designed based on cantilever type in which all rollers except printing ones have cantilever types, which could give more accurate machine precision as well as convenience for changing rollers and observing the process.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.449-449
• /
• 2007

OLED has many advantages of low voltage operation, self radiation, light weight, thin thickness, wide view angle and fast response time to overcome existing liquid crystal display (LCD)'s weakness. Therefore, It draws attention as promising display and has already developed for manufactured goods. Also, OLED is regarded as a only substitute of flexible display with a thin display. A considerable portion of the light originating film emissive centers buried in a solid film never escapes due to internal reflection at the air-film interface and is scattered as edge emission or dissipated within the solid film This is one of the major reasons why the luminous power efficiency of OLED remains low, in spite of research progress in OLED. Although several ways of overcoming this difficulty have been reported, no comprehensive method has been proposed yet. In this paper, we propose that use of anti-reflective coating layers.