• Structural Engineering and Mechanics
• /
• v.13 no.5
• /
• pp.465-478
• /
• 2002

This study lays emphasis on the development of efficient analytical models for a multistory structure with wings, including the in-plane deformation of floor slabs. For this purpose, a multistory structure with wings is regarded as the combination of multistory structures with rectangular plan and their junctions. In addition, a multistory structure with a rectangular plan is considered to be an assemblage of two-dimensional frames and floor slabs connecting two adjacent frames at each floor level. This modeling, concept can be easily applied to multistory structures with plans in the shape of L, T, Y, U, H, etc. To represent the in-plane deformation of floor slabs efficiently, a two-dimensional frame and the floor slab connecting two adjacent frames at each floor level are modeled as a stick model with two degrees of freedom per floor and a stiff beam with shear deformations, respectively. Three models are used to investigate the effect of in-plane deformation of the floor slab at the junction of wings on the seismic behavior of structures. Based on the comparison of dynamic analysis results obtained using the proposed models and three-dimensional finite element models, it could be concluded that the proposed models can be used as an efficient tool for an approximate analysis of a multistory structure with wings.

• Structural Engineering and Mechanics
• /
• v.77 no.4
• /
• pp.463-472
• /
• 2021

Fully rigid floor diaphragm is one of the main assumptions that are widely used in common practices due to its simple application. However, determining the exact degree of diaphragms flexibility cannot be easily accomplished without finite element modeling, which is an expensive and time-consuming procedure. Therefore, it is always possible that apparently rigid diaphragms, based on prescriptive limitations of seismic codes, experience some degrees of flexibility during the earthquakes. Since diaphragm flexibility has more uncertainties in asymmetric-plan structures, this study focuses on errors resulting from probable floor diaphragm flexibility of torsionally restrained structures. The analytical models used in this study were single-story buildings with asymmetric plan and RC shear walls. Although floor system is not considered explicitly, a wide range of considered diaphragm flexibility, from fully rigid to quite flexible, allows the results to be generalizable to a lot of lateral load resisting systems as well as floor systems. It has been shown that in addition to previously known effects of diaphragm flexibility, presence of orthogonal side elements during design procedure with rigid diaphragm assumption and rapid reduction in their absorbed forces can also be an important source to increase errors due to flexibility. Accordingly, from the obtained results the authors suggest designers to consider the possibility of diaphragm flexibility and its adverse effects, especially in torsionally restrained systems in their common designs.

• Journal of Korean Institute of Industrial Engineers
• /
• v.23 no.4
• /
• pp.669-686
• /
• 1997

In this research, an object-oriented Petri net model for representing a flexible process plan is proposed, which is hierarchically multi-faceted for supporting planning, scheduling, and shop floor control functions. The multi-faceted process plan model consists of the following: a) an object model which represents on object-oriented data model, b) a static model which represents a process flow model with process alternatives, and c) a dynamic model which represents a process activity model with resources alternatives, of a flexible process plan. Petri nets allow the static and the dynamic process plan models to be represented in a unified formalism with an ease of model transformation. The multi-faceted process plan model suggested in this paper, is illustrated with a prismatic port in comprehensive detail.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2007.11a
• /
• pp.129-132
• /
• 2007

From this research the construction civil official is simple with the parking floor finishing material, it improves the durability of the parking floor it uses the flexible FRP it will be able to secure the drainage quality it is excellent and it presents the efficient application plan from the construction site. The performance appraisal only efficiency with of result floor of parking area material bay it knows, the result where also the performance appraisal portion re-with roof bottom finishing is satisfied it showed. The flexible FRP it applies the material to the building as to diminish the damage of the bottom finishing material due to the deterioration and the conduct and the external force of the building it is exposed to the external environment, secures the quality of the material from the construction site and will contribute to the stability against the bottom finishing material.

• KIEAE Journal
• /
• v.17 no.4
• /
• pp.49-57
• /
• 2017

Purpose: Design inducement incentive item and formula on permitted floor area ratio in district detailed plan have been improved to reflect the actual application of guidelines and the social needs of city and architecture. However, the current guideline has a limit to realize the purpose of the plan. This study proposes improvement of the items and parameters in formula. Method: This study analyzed the district detailed planning guidelines since 2000 and the cases of general type district unit plan. In order to propose improved items and parameters, planing purposes and present parameters were compared and analyzed. Result: Items of guidelines have been changed according to public needs. High necessity items were applied to large parameters, and these items have been changed as the guideline changes. Diversity of items depended on regional characteristics, and parameters were more flexible than items for most cases. The purposes of plans, parameters and items were analyzed and it revealed four items needed improvement; the inducement of the limited building line, the improvement of the pedestrian and street environment, the necessity of the open space, and strengthening of the regional agreement. For improvement, this study added items and improved the relevance between items and sub-items. The parameters were improved by considering the importance, feasibility and comparing them with each other. Simulated result confirmed that proposed guideline is appropriate to operate, and also characteristics of area encourage to operate it more flexible.

• Proceeding of Spring/Autumn Annual Conference of KHA
• /
• 2005.11a
• /
• pp.171-175
• /
• 2005

The purpose of this study was to suggest the Support and Infill system for 126.6m$^2$-sized housing unit which meets residents' variety. The subjects were 100 housewives who lived in 126.6m$^2$-sized housing unit in the apartment complex, Busan. The data was collected by using model and questionnaire. The model was made to be same as the current 126.6m$^2$-sized floor plan. The residents preferred the flexible housing unit apartment complex. Also, the residents' needs for floor plan of housing unit were various. Therefore, the development of flexible housing unit is needed. On the basis of these findings, the support and infill system for 126.6m$^2$-sized housing unit was suggested.

• Proceedings of the Korea Society for Simulation Conference
• /
• 1996.05a
• /
• pp.15-15
• /
• 1996

A shop floor control system (SFCS) is the central part of a CIM system used to control the activities of several pieces of manufacturing equipment (e.g., NC machines, robots, conveyors, AGVs, AS/RS). The SFCS receives orders and related process plans, and then performs selecting a specific process routing, allocating resources, scheduling the workpieces, downloading the processing instructions (e.g., RS-274 instructions for NC machines, VAL II programs for robot), monitoring the progress of activities, detecting and recovering from errors, and preparing reports on the status of the manufacturing system. Simulation has been utilized in discovering control policies used for resolving shop floor be control problems such as resource contentions, part dispatching, deadlock. The simulation model must be designed to respond to real-time data coming from a shop floor. However, to rapidly build a realtime simulation model of SFCS cannot be easily accomplished. This talk is to address an automatic program generator of discrete event simulation model for shop floor control from process plans and resource models. The program generator is capable of constructing complete discrete simulation models for multi-product and multi-stage flexible manufacturing systems.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2009.11a
• /
• pp.35-39
• /
• 2009

Recently, the flat-plate structure is widely used because it has many advantages such as reduction of story height, long span etc than the RC rahmen structure. Furthermore, application of the flat-plate is on the increase because of flexible plan unlike wall structure. Long span have been at a disadvantage for vibration serviceability evaluation, however studies about vertical direction vibration of flat-plate structure has not been carried out. This study analysis the characteristics according to slab structure to make an experiment on vibration and floor impact noise for the flat-plate structure in construction performance laboratory in Kolon E&C R&D center, the flat-plate structure applied to the post-tension method, and the wall structure in apartment houses.

• Land and Housing Review
• /
• v.12 no.3
• /
• pp.67-78
• /
• 2021

After World War II, modular housing was developed as a means of quickly and efficiently meeting the housing supply demand. For the past 30 plus years, efforts have been made to improve modular housing in South Korea and to increase their competitiveness in the housing market. This study investigated modular houses based on a steel framed rahem structure which provides a flexible floor plan where walls are easily reconfigured to create rooms of various sizes and functions. Similar to the factory production methods used in the automotive industry, the modular housing industry can also benefit by standardizing such aspects as building components, manufacturing and construction methods, materials, process management, and floor plans. This study examined the feasibility of using a 3m × 3m module for developing various floor plans which are easy to produce and transport. Each 3m × 3m module can be configured to meet different living needs resulting in a complete home when multiple modules are connected. The module configurations can be varied to meet ground transportation and crane limitations. This study found that a 3m × 3m steel framed modular unit is a promising step towards providing residents with plans that meet their living preferences while improving and increasing the supply of modular houses.

• Korean Institute of Interior Design Journal
• /
• v.15 no.6 s.59
• /
• pp.150-158
• /
• 2006

The purpose of this study is to evaluate environment-friendly planning feature in Environment-friendly Certificated apartments and to use the basic planning data of housing. Seven Environment-friendly Certificated apartments have been analyzed. The findings of this study are as follows: Environment-friendly planning features are categorized into 4 items; floor planning feature, material planning feature, universal planning feature and environmental planning feature. Among floor planning features, natural sunlight, built-in closets, and differentiated floor plans are well considered, but the flexible floor plan for resident's lifestyle and green space are lack. Among material planning features, environment-friendly finishing materials, environment-friendly products and energy-efficient double-pane windows are well considered, but implementation for resource savings using recycled materials are lack. Among universal design planning features, removal of threshold and installation of safety device in bathroom are not well considered. Among environmental planning features, usage of alternative energy like solar energy are not applied. The environment-friendly planning features in interior space should be introduced in diverse ways.