• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.10
• /
• pp.1285-1295
• /
• 1999

An experimental study on heat transfer and flow characteristics of a circular impinging jet on a flat plate has been carried out. Of particular interests are the effects of nozzle wall thickness and nozzle exit pressure. Experimental apparatus has been designed to view heating plate coated by TLC from the opposite side of the nozzle in order to measure heat transfer rates for cases of very small nozzle to plate spacings. A visualization study of jet flows has also been performed. As the nozzle wall thickness increases at small nozzle to plate spacings, the effect of mixing is inhibited due to the confinement caused by the finite nozzle wall, consequently, heat transfer rates have been decreased. At small nozzle to plate spacings, heat transfer rates and nozzle exit pressures are increased together, therefore, enhancement of heat transfer at small nozzle to plate spacings should be considered in conjunction with the need of more fan power to generate the same Reynolds numbers.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.260-267
• /
• 2001

The objective of this study was to investigate the characteristics of jet flow and heat transfer caused by trapezoid rods array in impinging jet system. In this study, trapezoid rods have been set up in front of flat plate to serve as a turbulence promoter. The bottom width of trapezoid rod was W=4, 8mm and oblique angle were $80^{\circ}$. The space from rods to the heating surface was C=1, 2, 4mm, the pitch between each rods was P=30, 40, 50mm, and the distance from nozzle exit to flat plate was H=100, 500mm. This results were compared with the case without trapezoid rods. As a result, when rods are installed in front of the impinging plate, the acceleration of the jet flow and the eddies due to the rods seem to contribute to the heat transfer enhancement. Among test conditions, the heat transfer performance was best for the condition of W=8mm, C=1mm, P=30mm and H/B=10. The maximum heat transfer rate is about 1.9 times larger than that without trapezoid rods.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.11
• /
• pp.1659-1666
• /
• 2001

The objective of this study was to investigate the characteristics of air flow and heat transfer caused by trapezoid rods array in impinging air jet system. Trapezoid rods have been set up on front of flat plate to act as a turbulence promoter. Local Nusselt numbers were determined as a function of three parameters : (a) the space from re(Is to heating surface(C=1, 2, 4mm), (b) the pitch between each rods(P=30, 40, 50mm), (c) the distance from nozzle exit to flat plate(H/B=2, 6, 10). The measurements were compared with those of the experiment without trapezoid rods. As a result, when rods are installed in front of the impinging palate, the acceleration of the flow and the eddies due to the rods seem to contribute to the heat transfer enhancement. Heat transfer performance was best under the condition of C=1mm and as the pitch is 30mm. The maximum rate of heat transfer augmentation is about 1.9 times greater compared to that without trapezoid rods.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.12
• /
• pp.1726-1734
• /
• 1998

This paper focuses on the unsteady close-contact melting phenomenon occurring between a phase change material kept at its melting temperature and a flat surface on which constant heat flux is imposed. Based on the same simplifications and framework of analysis as the case of constant surface temperature, an approximate analytical solution which depends only on the liquid-to-solid density ratio is successfully derived. In order to keep consistency with the known solution procedure, both the dimensionless wall heat flux and the Stefan number are properly redefined. The obtained solution proves to agree quite well with the published numerical data and to be capable of resolving the fundamental features of unsteady close-contact melting, especially in the presence of the solid-liquid density difference. The density ratio directly affects the film growth rate and the initial value of solid descending velocity, thereby controlling the duration of unsteady process. The effects of other parameters can be evaluated readily from the steady solution which is implied in the normalized result. Since the dimensionless surface temperature for the present boundary condition increases from zero to unity along the evolution path of the liquid film thickness, the unsteady process lasts longer than that for the case of isothermal heating.

• Journal of computational fluids engineering
• /
• v.14 no.1
• /
• pp.70-77
• /
• 2009

In this study, time-dependent numerical analysis was carried out to investigate the plasma jet impingement on a flat plate, and a compressible form of two-dimensional inviscid gas dynamics equations were solved using the flux corrected transport algorithm. The mathematical modeling of Joule heating in the polycarbonate capillary bore and the mass ablation from the bore wall was incorporated in the numerical analysis and the series of computation was performed for three cases depending on the distance of the opposing plate from the capillary exit. The computational results reveal that the presence of the opposing plate does not affect the flow conditions inside the capillary when compared to the case of open-air plasma discharge. In the exterior region, the flow structure shows the typical supersonic underexpanded jet which consists of the strong Mach disk in front of the opposing plate and the barrel shock at the side of the jet. It is found that the shock evolution becomes more quasi-steady when the plate distance decreases. Also, the effects of the distance between the capillary bore exit and the opposing plate on the flow conditions along the opposing plate are investigated and the pressure variation on the plate shows more complicated interaction between the plasma discharge and the opposing plate when the location of plate becomes closer to the capillary exit.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.40 no.6
• /
• pp.46-56
• /
• 1998

This study was performed to investigate thermal performances of two different types of flat-plate solar collector systems; natural circulation system and forced circulation system. Conclusions obtained from this study are summarized as follows; 1) In the natural circulation system, the total heat amounts retrieved by starting recovery soon after sunrise were ranged from 10.28 to 17.20MJ/m$^2$, while the total heat amounts retrieved by starting recovery after sunset were ranged from 5.31 to 10.77MJ/m$^2$. 2) The collector efficiency in natural circulation system were ranged from 51.1% to 54.1% when the collected heat was retrieved after sunrise and were 65.8~78.0% when the collected heat was retrieved soon after sunset. 3) According to the regression analysis between fluid flow rates and fluid temperature difference at inlet and outlet of collector pipe, there was high regressive corelations with regression coefficient, r, of 0.982. 4) The collector efficiencies estimated for forced circulation system were 73.1~88.6%, and 78.4~94.8%, and 64.2%~74.5%, respectively when fluid circulation rates were 4.2 l/min, and 7.0 l/min, respectively.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.9
• /
• pp.904-913
• /
• 2001

The objective of this study was to investigate the characteristics of jet flow and heat transfer caused by trapezoid rods array in impinging jet system. In this study, trapezoid rods have been set up in front of flat plate to serve as a turbulence promoter. The bottom width of trapezoid rod was W=4, 8 mm and oblique angle were 80$^{\circ}$. The space from rods to the heating surface was C=1, 2, 4 mm, the pitch between each rods was P=30, 40, 50 mm, and the distance from nozzle exit to flat plate was H=100, 500 mm. This results were compared with the case without trapezoid rods. As a result, when rods are installed in front of the impinging plate, the acceleration of the jet flow and the eddies due to the rods seem to contribute to the heat transfer enhancement. Among test conditions, the heat transfer performance was best for the condition of W=8 mm, C=1 mm, P=30 mm and H/B=10. The maximum heat transfer rate is about 1.9 times larger than that without trapezoid rods.

• Textile Coloration and Finishing
• /
• v.31 no.3
• /
• pp.155-164
• /
• 2019

This study comparatively analyzed hair bleaching and degree of damage by the temperature of a heating tool after coloring hair with a permanent, semi-permanent or plant hair dye. According to analysis by spectrophotometer, 'semi-permanent hair dye' was the highest, followed by 'permanent hair dye' and 'plant hair dye' in terms of changes in $L^*$ values. In terms of changes in hair shape when analyzed using FE-SEM, 'semi-permanent hair dye($150^{\circ}C$ or lower)' was the greatest, followed by 'plant hair dye($180^{\circ}C$ or lower)' and 'permanent hair dye($200^{\circ}C$ or lower)'. Therefore, it is reasonable to flat iron hair at low temperature. According to the test, amino acid values gradually decreased in both bleached and colored hair. The results obtained through TGA-based thermal analysis confirmed that as brightness increases, hair moisture contents decrease. This study aimed to protect hair by suggesting a correct use of a flat iron by the hair dye type during hair coloring. It appears that the study results would help hairdressers minimize hair damage by using a hair dye at proper temperature.

• Solar Energy
• /
• v.11 no.1
• /
• pp.16-26
• /
• 1991

This paper studies development of a solar thermosyphon hot water system which is suitable to korean climate and life style, to save energy consumed for domestic water heating. The system consists of two flat plate collectors(or three flat plate collectors) connected in parallel and a storage tank of 300 liter capacity with heat exchanger and the optimum system was designed through the comparative measurements of five different storage tanks. The developed system manufactured with domestic materials were installed in residential buildings in seven cities(Seoul, Pusan, Taegu, Kwangju, Taejeon, Kangneung, Cheju) for demonstration and field test and results show possibility for commercialization.

• Journal of Conservation Science
• /
• v.37 no.4
• /
• pp.380-390
• /
• 2021

The purpose of this study is to scientifically analyze the rocks of the Obongsan Mountain in Boseong, Jeollanam-do, which contains the largest extant quarry of Gudlejang (flat stone for heating) in Korea, and to scientifically determine the petrological characteristics of the area and the reasons for its use as a quarry. The rocks in the quarry are composed of light-green lapilli tuff, containing various types of lithic fragments and crystalline fragments in a vitreous matrix consisting of the fine feldspar crystals. The main constituent minerals were identified as quartz, plagioclase, mica, chlorite and opaque minerals. When the major element compositions were plotted on a Na₂O+K₂O versus SiO₂ diagram, all samples were situated in the same compositional area as rhyolite. In addition, the result of magnetic susceptibility measurement also showed a similar range of values, of 1.30 ~ 4.85 (×10^-3 SI), indicating that samples were fractionated from the same magma. Both rock types showed similar apparent specific gravity values of 2.32 ~ 2.60. In particular, plate-shaped joints are well developed in the Obongsan Mountain area, and many areas exhibit talus terrain. In conclusion, the rocks of this area is interpreted to used for a site of Gudlejang quarrying, because the rocks were easily obtainable due to the terrain characteristics, and their petrological properties made them suitable for use as Gudlejang stone.