• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 춘계학술대회논문집
• /
• pp.159-162
• /
• 2000

Wrinkles and shape distortions are generated during the forming of B-pillar(or center pillar) which is a component of the automobile side-frame. The stretch flanging modes at the joining part of the B-pillar and the roof-rail or the side-still give rise to forming problems when taior-welded blanks are applied to the side-frames. The authors simplified B-pillar lower part to T shaped section to investigate the forming behaviors. Three of die step locations and two of blank types were tested to show the effects of weld line locations and edge conditions on he forming of tailor welded blanks. The heights of body wrinkles and the strain distribution in the stretch flanged area were measured and compared.

• 한국기계기술학회지
• /
• 제13권1호
• /
• pp.105-112
• /
• 2011

Increasing needs for light weight and high safety in modern automobiles induced the wide application of high strength steels in automotive body structures- The main difficulty in the forming of sheet metal parts with high strength steel is the large amount of springback including sidewall curl and twist in channel shaped member parts- Among these shape defects, twist occurs frequently and requires numerous reworks on the dies to compensate the shape deviation- But until now, it seems to be no effective method to reduce the twist in the forming processes- In this study, a new forming process to reduce the twist deformation during the forming of automotive structural member was suggested- This method consists of forming and restriking of embosses on the sidewall around the stretch flanging area of the part- and was applied in the forming process design of an automotive front side inner member with high strength steel- To evaluate the effectiveness of the method, springback analysis using $Pamstampa^{tm}$ was done- Through the analysis results, the suggested method was proven to be effective in twist reduction of channel shaped parts with stretch flanging area.

• Journal of Advanced Research in Ocean Engineering
• /
• 제4권3호
• /
• pp.115-123
• /
• 2018

This study was carried using the new approach method to design appropriately the Loading Arm length and the alarm setting according to ship movements on Loading and Unloading marine Berth. The quasi-static mooring analysis was performed to estimate 110,000DWT ship's movements based on environmental conditions such as wind, current and wave. The mooring motion of the ship is very important to determine the loading arm scope, and in this case, the operation condition is performed on the ship without considering the damaged condition of the mooring line because the ship movement in case of damage is larger than intact, and all operations are stopped, the loading arm being released due to control system. From the result of mooring analysis, motion displacements, velocities and accelerations were simulated. They were used to simulate the maximum drifting speeds and distances. The maximum drifting speeds were checked to be satisfied within drifting speed limits. The total maximum drifting distances were simulated with alarm steps of the new approach method. Finally, the loading arm envelopes using the total maximum drifting distances were completed. Therefore, it was confirmed that the new approach method for loading arm envelopes and alarm settings was appropriate from the above results. In the future, it will be necessary to perform the further advanced dynamic mooring analysis instead of the quasi-static mooring analysis and to use the precise computer program analysis for various environments and ship movement conditions.

• 대한기계학회논문집A
• /
• 제37권2호
• /
• pp.161-168
• /
• 2013

오늘날 자동차 산업에서 가장 대두되고 있는 충돌 안전성과 배기가스의 감축을 위해서 dual phase 강, ferrite bainite 강 등의 고강도 강판이 개발 되었다. 이러한 강재는 주로 차체 구조부에 적용되며, 적용시에 차체 구조부가 가져야 하는 강도와 디자인 적인 측면에서 사용자의 요구에 맞추기 위하여 홀 플랜징 가공이 자주 사용된다. 이때 재료의 성형성을 알아보기 위한 홀 확장성 평가가 수행된다. 홀 확장실험에서는 크랙 생성 전후의 하중의 차이가 매우 작기 때문에, 단축 인장 시험에서와 같이 하중의 변화로 크랙 발생 유무를 판단하기가 쉽지 않다. 따라서 본 연구에서는 기존의 홀 확장성 평가에서 사람의 눈으로 크랙의 발생 유무를 판단하는 방법의 부정확성을 보완하기 위해 CCD 카메라를 이용하여 크랙의 발생 유무를 판단하는 시스템을 개발하였다.