• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05d
• /
• pp.69-71
• /
• 2003

Mechanical Properties, such as tensile strength, elongation, and tear strength, decreased according to increasing the load of ATH, volume resistivity, AC break down strength, and tracking resistance for HVI SC contained ATH treated by vinyl Silane were better than those for HVI SC were contained ATH treated by other surface treatment agent, such as stearic acid and acryl silane.

• Journal of Sensor Science and Technology
• /
• v.21 no.4
• /
• pp.298-302
• /
• 2012

This paper describes the design and fabrication of a low frequency vibration driven high-efficiency electromagnetic energy harvester based on FR(Flame Resistance)-4 spring which converts mechanical energy into useful electrical power. The fabricated generator consists of a vertically polarized NdFeB permanent magnet attached to the center of spring and a planar type copper coil which has higher efficiency compare with cylindrical type coil. ANSYS finite analysis and Matlab were used to determine the resonance frequency and output power. The generator is capable of producing up to 1.36 $V_{pp}$ at 9 Hz, which has the maximum power of 639 ${\mu}W$ with a load resistance of $3.25k{\Omega}$.

• Elastomers and Composites
• /
• v.27 no.1
• /
• pp.13-19
• /
• 1992

In this work, properties of ABS/AES blends were investigated. Blends were prepared by casting from THF. The thermal stability, light resistance, storage modulus and flame retardancy were measured by thermogravimetric analysis, cole. difference in Fade-o-meter, Rheovibron, and limiting oxygen index(LOI). The thermal stability, light resistance and storage modulus increased with increasing contents of AES. ABS and AES showed similar LOI. The LOI of the ABS/AES blends increased with rising contents of AES but all the blends were found to be flammable. It was observed that ABS and AES was incompatible from the morphology by scanning electron microscope(SEM).

• Bulletin of the Korean Chemical Society
• /
• v.35 no.6
• /
• pp.1665-1669
• /
• 2014

Four multialkoxy-functionalized siloxane base-polymers (BP-1~4) were synthesized through either hydrosilylation or condensation reactions in order to prepare multi-networked siloxane polymers having appropriate physical properties for protective coating in fabrications of electronics. Formulations of 4 base-polymers gave coating materials A and B. Product A showed well-controlled flowing and leveling properties, and product A-2 was successfully applied to protective insulating coating for junction areas of connectors and chips in PDP controller. Tack free time, extrusion rate, dielectric breakdown voltage, hardness, thermal stability, water resistance and flame resistance of products A and B were examined.

• KIEAE Journal
• /
• v.7 no.4
• /
• pp.135-140
• /
• 2007

In this study we settled the trouble of the MgO board of existence by this research. We changed the wooden one of the main ingredient of a board to a perlite and a mineral particle in the aluminum hydroxide group and proceeded with a study to physical character and fire resistance efficiency improvement. The result yellowing phenomenon could be improved and it was possible to reduce size decrease of pin hole and the frequency of occurrence. We found out that the in case of absorbed amount added 5~8% corresponding to the weight decreases the acrylic group emulsion suddenly. So this product is improved with the bending strength and water-resistance. After behavior stop time measurement of a mouse for experiments was measured at the time of a gas harmful effect test, an improved MgO board appeared more highly for an average of 138 seconds compared with a board of existence.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.45 no.1
• /
• pp.45-54
• /
• 2003

The effects of binder content and silica sand content on the durability characteristics of lightweight polymer concretes are examined. As a result, the flame lingering times using unsaturated polyester resin and non-combustible polyester resin were 60∼120 and 0∼4 seconds respectively, and the combustion lengths were 9∼11 mm and 0∼3 mm, respectively. Thus it is believed that the lightweight polymer concrete was incombustible and the light weight polymer concrete in which non-combustible material was added was perfectly non-combustible. The percent of original mass of lightweight polymer concrete, according to the freezing-thawing experiment, was below 0.3 %, which was much less than that of cement concrete. The pluse velocity, for the case of the binder content 28 %, showed the minimum decreasing rate for the lightweight polymer concrete with silica sand content of 50 %. The higher the binder content, the greater the durability. That is much higher than other material and believed that the freezing-thawing was suppressed by a low absorption.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2016.05a
• /
• pp.149-150
• /
• 2016

The membrane structure is being applied in structures for various uses for its many advantages as permeableness, lightweightness, constructability, resource saving, and management cost reduction, and the usage is being expanded. However, despite the development of membrane structure, the standard for architectural membrane performance that considered fire safety is still inadequate. Therefore, this study applied basalt fiber with flame resistance on architectural membrane. Also, this study confirmed the membrane applicability of basalt fiber through comparison with existing architectural membrane.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.04a
• /
• pp.77-78
• /
• 2022

This study compared the fire safety standards for windows of Korea, the U.S. and Japan to prevent fire expansion through exterior wall openings, and conducted experiments using PVC and aluminum window frames, which are widely used in Korea.The experiment is KS F 2845 which combines frames of the same thickness and area with single-window form and 1 hour fire resistance glass with 8T thickness. Experiments showed that the PVC window was about 9 minutes and the aluminum window was about 26 minutes. However, in Korea, there are no test standards for windows installed at the opening of the exterior wall. In addition, fire safety standards for windows shall be established along with the designation of fire prevention zones.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.11a
• /
• pp.54-55
• /
• 2021

This study compared the fire safety standards for windows of Korea, the U.S. and Japan to prevent fire expansion through exterior wall openings, and conducted experiments using PVC and aluminum window frames, which are widely used in Korea.The experiment is KS F 2845 which combines frames of the same thickness and area with single-window form and 1 hour fire resistance glass with 8T thickness. Experiments showed that the PVC window was about 9 minutes and the aluminum window was about 26 minutes. However, in Korea, there are no test standards for windows installed at the opening of the exterior wall. In addition, fire safety standards for windows shall be established along with the designation of fire prevention zones.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.2
• /
• pp.608-613
• /
• 2010

This study is on development of UV-cured water soluble coating composition which have more improved anti-cigar burning to prevent a surface of PVC tile from damage of heat. To make an anti-cigar burning coating solution, thermostable agent that synthesize main materials phosphorus compound, guanidine and ammonium phosphate dibasic used temporary flame retardants, changing their contents from 10 to 30wt% against quantities of resin and compounded. After coating PVC tiles using bar-coating method that can adjust a thickness, we estimated surface properties of coated layer such as anti-cigar burning, adhesive power, chemical resistance, thickness of coating, and so on. Results showed that a coating composition added 30 wt% of phosphorus compound and coated with No.12 bar-coater had the best optimized surface property in anti-cigar burning effect, adhesive power and chemical resistance. Also, we could find anti-cigar burning effect was improved as thermostable agents content and coating thickness increased.