• Fire Science and Engineering
• /
• v.11 no.4
• /
• pp.15-23
• /
• 1997

A series of measurements and visualization to investigate the extingushiment of water sprays with pool fires is presented. Fire source is a small-scale pool burner with methanol, ethanol and gasoline. Measurements of temperature, O2, CO2, and CO concentrations along the plume centerline are carried out to observe pool structures without water sprays. Visualization by the Ar-ion laser sheet flow pattern of droplets of the sprays above the pool fires. It is observed than in the case of methanol and ethanol, water sprays continuously penetrate into the center of fuel surfaces. The gasoline pool fire allows intermittent penetration of water sprays because of pulsating characteristics of the gasoline flame. To evaluate the cooling effect of the fuel surface by the sprays, the temperature was measured at the fuel surface. As soon as the mists reach the fuel surface of methanol and ethanol, the temperatures of the fuel surface decrease rapidly below the boiling point, and then the fires are extinguished. Due to the application of mist upon the gasoline fire, though the fuel temperature decrease abruptly at the time of the injection, such a repid decrease do not continue till the extinction point.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 1997.11a
• /
• pp.518-525
• /
• 1997

A series of measurements and visualization to investigate the interaction of water sprays with pool fires is presented. Fire source is a small-scale pool burner with methanol, ethanol and gasoline. Measurements of temperatures, $O_2$, $CO_2$, and CO concentrations along the plume centerline are carried out to observe pool fire structures without water sprays. Visualization by the Ar-ion laser sheet shows flow pattern of droplets of the sprays above the pool fires. It is observed that in the case of methanol and ethanol, water sprays continuously penetrate into the center of fuel surfaces. The gasoline pool fire allows intermittent penetration of water sprays because of pulsating characteristics of the gasoline flame. To evaluate the cooling effect of the fuel surface by the sprays, the temperature was measured at the fuel surface. As soon as the mists reach the fuel surface of methanol and ethanol, the temperatures of the fuel surface decrease rapidly below the boiling point, and then the fires are extinguished. Due to the application of mist upon the gasoline fire, though the fuel temperature decrease abruptly at the time of the injection, such a rapid decrease do not continue till the extinction point.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.6
• /
• pp.768-776
• /
• 2015

This study was performed to understand combustion properties four major Indonesian wood species such as Albizia, Gmelina, Mangium and Mindi were investigated by cone-calorimeter for better utilization of theses wood species. Heat release rate (HRR), total heat release (TSR), specific mass loss rate (SMLR), effective heat of combustion (EHC), time to ignition (TTI), flame time (FT), specific extinction area (SEA), smoke production rate (SPR) and CO compound production rate were measured. HRR, THR and FT were proportional to the density of woods. Albizia showed the highest HRR, while Mindi had the lowest HRR. For SPR, Albizia showed the highest value due to its higher SEA. On the other hand, Mindi had the lowest SPR due to a lower SEA value. The highest smoke emission was for Albizia at the beginning of combustion. After 300 seconds, smoke emission of Gmleina and Mangium was increased greatly. Mangium and Mindi showed the highest total carbon dioxide emission. Expecially, Gmelina released the highest carbon monoxide during the combustion period and presented three times higher $CO/CO_2$ ratio than those of other species due to incomplete combustion.

• The Journal of the Petrological Society of Korea
• /
• v.23 no.2
• /
• pp.61-73
• /
• 2014

The dextral strike-slip Yecheon Shear Zone of (E)NE-(W)SW trend is developed in the Pukhumyeon-Pyeongeunmyeon area, Gyeongsangbukdo, in the central part of Sobaeksan Massif, Korea which mainly consists of Precambrian metasedimentary rocks and Mesozoic granite. This paper researched the relative formation time, the deformation temperature, and the distribution of ultramylonite zone of Yecheon Shear Zone from the analysis of their deformed rock structures and microstructures. There are the mylonite foliation and stretching lineation by shear deformation, and the (E)SE-vergence gentle plunging, moderately inclined tight fold defined by the gneissosity and mylonite foliation as ductilely deformed main rock structures. Flame perthites, myrmekites, microfractures, microkinks, kinkband, and undulatory extinction are recognized as characteristic microstructures in feldspars during ductile shear deformation. Patterns of c-axis fabrics of recrystallized quartz aggregate display single girdle and type I crossed girdle where the rhomb and basal slip systems are predominant. The shearing senses on sense-of-shear plane show top-to-the-NE and top-to-the-SW on the predominant NW-dipping and subordinate SE-dipping mylonite foliations, respectively. These characteristic rock structures and microstructures suggest that the Yecheon ductile shearing occurred under $350{\sim}450^{\circ}C$ deformation temperature after the tight folding. The (E)NE trending ultramylonite zone of Yecheon Shear Zone, which passes through the Pulnobong and the north part of Pakdalsan, is established from the zonal distribution of Precambrian metasedimentary rocks and the grain-size distribution of feldspars in the Precambrian metasedimentary rocks and quartzs in the Mesozoic granite.