• Journal of Korean Society for Atmospheric Environment
• /
• v.24 no.1
• /
• pp.91-99
• /
• 2008

A multilayer tower-type photoreactor, in which $TiO_2$-coated glass-tubes were installed, was used to measure the vapor-phase BTEX removal efficiencies by ozone oxidation ($O_3$/UV), photocatalytic oxidation ($TiO_2$/UV) and the combination of ozone and photocatalytic oxidation ($O_3/TiO_2$/UV) process, respectively. The experiments were conducted under various relative humidities, temperatures, ozone concentrations, gas flow rates and BTEX concentrations. As a result, the BTEX removal efficiency and the oxidation rate by $O_3/TiO_2$/UV system were highest, compared to $O_3$/UV and $TiO_2$/UV system. The $O_3/TiO_2$/UV system accelerated the low oxidation rate of low-concentration organic compounds and removed organic compounds to a large extent in a fixed volume of reactor in a short time. Therefore, $O_3/TiO_2$/UV system as a superimposed oxidation technology was developed to efficiently and economically treat refractory VOCs. Also, this study demonstrated feasibility of a technology to scale up a photoreactor from lab-scale to pilot-scale, which uses (i) a separated light-source chamber and a light distribution system, (ii) catalyst fixing to glass-tube media, and (iii) unit connection in series and/or parallel. The experimental results from $O_3/TiO_2$/UV system showed that (i) the highest BTEX removal efficiencies were obtained under relative humidity ranging from 50 to 55% and temperature ranging from 40 to $50^{\circ}C$, and (ii) the removal efficiencies linearly increased with ozone dosage and decreased with gas flow rate. When applying Langmuir-Hinshelwood model to $TiO_2$/UV and $O_3/TiO_2$/UV system, reaction rate constant for $O_3/TiO_2$/UV system was larger than that for $TiO_2$/UV system, however, it was found that adsorption constant for $O_3/TiO_2$/UV system was smaller than that for $TiO_2$/UV system due to competitive adsorption between organics and ozone.

• Proceedings of the KOSOMBE Conference
• /
• v.1996 no.05
• /
• pp.84-87
• /
• 1996

We have been developed electrohydraulic left ventricular assist device and done various in vivo evaluation on the device. Through the in vivo experiment conducted from Jan. 23, 1996 to Feb. 8, we could have experience of long-term evaluation fur the first time. The sheep used in this experiment had survived for 16 days. We used new actuator with reduced size and linear motion guide replacing oil box and ball bearings. Also, we used improved blood chamber with reduced size, reduced weight facilitating fixing the chamber to animal's body, and polymer sac having improved folding pattern. Against suction problem, we used absolute pressure limiter only. Motor current for driving this new actuator was not much higher than older one. Effective stroke volume was about 48 cc. Thrombosis was found around top area and peripheral boundary of the sac and valves. There was no sign of damage from suction problem in the atrium observed at autopsy. Main cause of death was presumed to be progressive formation of thrombosis in the cannulae. In this paper, the results of this experiment are documented.

• Journal of KIISE:Computing Practices and Letters
• /
• v.8 no.3
• /
• pp.344-355
• /
• 2002

Having a variety of good characteristics against other pattern recognition techniques, Multilayer Perceptron (MLP) has been used in wide applications. But, it is known that Error Backpropagation (EBP) algorithm which MLP uses in learning has a defect that requires relatively long leaning time. Because learning data in pattern recognition contain abundant redundancies, in order to increase learning speed it is very effective to use online-based teaming methods, which update parameters of MLP pattern by pattern. Typical online EBP algorithm applies fixed learning rate for each update of parameters. Though a large amount of speedup with online EBP can be obtained by choosing an appropriate fixed rate, fixing the rate leads to the problem that the algorithm cannot respond effectively to different leaning phases as the phases change and the learning pattern areas vary. To solve this problem, this paper defines learning as three phases and proposes a Instant Learning by Varying Rate and Skipping (ILVRS) method to reflect only necessary patterns when learning phases change. The basic concept of ILVRS is as follows. To discriminate and use necessary patterns which change as learning proceeds, (1) ILVRS uses a variable learning rate which is an error calculated from each pattern and is suppressed within a proper range, and (2) ILVRS bypasses unnecessary patterns in loaming phases. In this paper, an experimentation is conducted for speaker verification as an application of pattern recognition, and the results are presented to verify the performance of ILVRS.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.36 no.1
• /
• pp.71-77
• /
• 2010

The water fern Azolla belongs to the Azollaceae and forms a symbiotic association with a $N_2$-fixing cyanobacterium, referred to as Anabaena azollae, and this association has currently been demonstrated to have potential as a nitrogen source for rice production. Because of that, Azolla fern has been used not only as organic manure in southern China and northern Vietnam for a long time but also as food for animate creatures in the underwater and decontaminant in the water. However, the phenolic compounds and active materials of Azolla have not been examined in detail in the past studies. In the present study, anti-oxidant ability test and experiment to find a particular active material of Azolla imbricata and Azolla imbricata fraction (AIF) were performed. In anti-oxidant test such as DPPH test and lipoxygenase inhibition test, the value of test represented high activities compared with authentic sample - green tea and NDGA (nordihydroguaiaretic acid). In MMP-1 test, related to collagen protection and elasticity of skin, its inhibitory effect was measured over 75 %, and the phenolic compounds of AIF related with this activity were confirmed luteolin derivatives by using FT-IR spectroscopy, element analyzer (EA) and Liquid chromatography-MASS spectroscopy.

• Journal of the Korean Applied Science and Technology
• /
• v.38 no.5
• /
• pp.1335-1344
• /
• 2021

Ginsenoside Compound K is a triterpene saponin found in the leafs, stems and roots of Panax ginseng. This study aimed to prepare a valuable ginsenoside Compound K using ginseng extracts with the enzyme(Plantase). Plantase showed very efficient activity to produce Compound K from ginseng extracts. Plantase exhibited the highest activity at pH 5 and 50 ℃, as a result of investigating the yield of Compound K by changing the temperature and pH, while fixing the enzyme concentration to 10% or 15% over 48 hours of reaction time. Under optimium conditions, Plantase produced and accumulated Compound K over 35 wt% of whole ginseng extracts. Antimicrobial activitiy of bioconvertied ginseng extracts showed selectivity against Cutibacterium acnes KCTC 3314. Minimal inhibitory concentration (MIC) of bioconverted ginseng extract (35% of Compound K enriched extract) against Cutibacterium acnes KCTC 3314 strain is 31.25ug/mL. These results suggest that the Compound K enriched extract is potential materials for cosmetic products and Plantase is a very useful enzyme for Compound K production.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.10
• /
• pp.39-49
• /
• 2011

Recently PBD method, one of acceleration of consolidation methods is used in the soft ground to shorten consolidation time for fast settlement during construction. It is economical and easy to work. Discharge capacity of PBD is sensitive in proportion to thickness of soft ground layer, and drainage of PBD declines due to disturbance effect in surrounding ground by mandrel used for vertical drainage setting and setting machines and type. Also, deviation of discharge capacity is large according to ground condition, construction condition and soil properties. In addition, when embankment loading is not conducted instantly after PBD setting due to rain or lack of embankment material supply, it causes leaving period problems. But cause and analysis of those problems for discharge capacity is lack. So, in this test, ground improvement and discharge capacity is investigated by implementing composite discharge capacity test for analysis of an effect factor of PBD discharge capacity with leaving period. After fixing the vertical drain on a cylindrical cylinder, put churned sample into the cylinder. Then leave 0day, 30day, 60day and 90day. And then, load following the loading step of 30, 70 and 120kPa using a pressure device. As a result, the longer leaving period, discharge capacity is reduced. It is caused by a decrease of discharge area caused by creep transformation moisture absorption of PBD filter after long leaving period.

• Journal of Software Assessment and Valuation
• /
• v.16 no.1
• /
• pp.65-79
• /
• 2020

As Programmable Logic Controllers (PLCs), popular components in industrial control systems (ICS), are incorporated with the technologies such as micro-controllers, real-time operating systems, and communication capabilities. As the latest PLCs have been connected to the Internet, they are becoming a main target of cyber threats. This paper proposes two sanitizers that improve the security of uC/OS-II based firmware for a PLC. That is, we devise BU sanitizer for detecting out-of-bounds accesses to buffers and UaF sanitizer for fixing use-after-free bugs in the firmware. They can sanitize the binary firmware image generated in a desktop PC before downloading it to the PLC. The BU sanitizer can also detect the violation of control flow integrity using both call graph and symbols of functions in the firmware image. We have implemented the proposed two sanitizers as a prototype system on a PLC running uC/OS-II and demonstrated the effectiveness of them by performing experiments as well as comparing them with the existing sanitizers. These findings can be used to detect and mitigate unintended vulnerabilities during the firmware development phase.

• Journal of the Korean Society of Radiology
• /
• v.16 no.4
• /
• pp.435-442
• /
• 2022

The heel effect creates a density difference in the X-ray images because the intensity of the anode and cathode side of the X-ray tube is not equal. The purpose of this study is to evaluate the density difference due to the heel effect by rotating the step wedge by 180 degrees and then changing the distance. After fixing the tube voltage and tube current to 72 kVp and 10 mAs, the forward and reverse directions were taken using a step wedge. At this time, the distance (80 cm ~ 130 cm) was taken at 10 cm intervals, and the density value was measured by setting the region of interest for each step of the step wedge through the M6 program. First, the difference in intensity between the anode and the cathode was confirmed through the radiation exposure test. In addition, when the distance (from 80 cm to 130 cm) was changed, the difference in density between the cathode and the anode decreased as the projection distance increased. As a result, images of uniform density can be obtained as the projection distance increases.

• Journal of the Korean Chemical Society
• /
• v.52 no.3
• /
• pp.303-314
• /
• 2008

The purpose of this study was to understand the experiment for measuring chemical reaction rate by precipitate formation and to develop experiments applying small-scale chemistry. For this study, the experimental method for measuring the effect of concentration and temperature on chemical reaction rates presented in the 10 high school science textbooks were classified by their experimental methods of confirming production. Subsequently, problems observed in carrying out the experiments for measuring chemical reaction rates by precipitate formation frequently presented in the 10 high school science textbooks were analyzed. Experiments applying small-scale chemistry were developed measuring chemical reaction rate by precipitate formation. According to the result of this study, there were some problems in the experimental method of precipitate formation for measuring chemical reaction rates presented in the high school science textbooks. Those problems in the science textbook experiments were insufficient specification of mixing methods of reaction solutions, obscurity of knowing when the character letter X disappeared, time delay in collecting the experimental data, formation of hazardous sulfur dioxide, uneasiness of fixing water bath container, controlling the reaction temperature, and low reproducibility. Those problems were solved by developing experiments applying smallscale chemistry. Presenting the procedure of mixing reaction solutions on the A4 reaction paper sheet made the experimental procedure clearly, using well plates and stem pipette shortened the reaction time and made it possible to continuously collect the experimental data. Furthermore, the quantity of hazardous sulfur dioxide was reduced 1/7 times and the time when the character letter X disappeared could be observed clearly. Since experiments for measuring the effect of concentration and temperature on chemical reaction rates could be performed in 30 minutes, the developing experiments applying SSC would help students understand the scientific concepts on the effect of concentration and temperature on chemical reaction rates with enough time for experimental data analysis and discussion.

• Journal of Navigation and Port Research
• /
• v.39 no.1
• /
• pp.45-53
• /
• 2015

These days Container Terminals are focusing on increasing the quantity of containers and shipping lines choose Terminals by referring to the key elements of a terminal to perform the overall operation the fastest such as the location of the terminal, discharging ability, keeping environment, and other elements related to shipping in general. Container terminal is able to offer On-Dock service has become an important factor for shipping lines to choose that terminal. In this paper, we propose an algorithm for On-Dock system work algorithm, the algorithm Empty container exports, Full Container algorithm and The aim of our study focus on both container's gate out time and search for the effective terminal operation which is using the general On-Dock system through several algorithm like container batch priority, gate in and out job priority and empty container yard equipment allocation rule based on the automatic allocation method and manual allocation scheme for container. Gathering these information, it gives the priority and yard location of gate-out containers to control. That is, by selecting an optimum algorithm container, container terminals Empty reduces the container taken out time, it is possible to minimize unnecessary re-handling of the yard container can be enhanced with respect to the efficiency of the equipment. Operations and operating results of the Non On-Dock and On-Dock system is operated by the out work operations (scenarios) forms that are operating in the real Gwangyang Container Terminal derived results. Gwangyang Container terminal and apply the On-Dock system, Non On-Dock can be taken out this time, about 5 minutes more quickly when applying the system. when managing export orders for berths where On-Dock service is needed, ball containers are allocated and for import cargoes, D/O is managed and after carryout, return management, container damage, cleaning, fixing and controlling services are supported hence the berth service can be strengthened and container terminal business can grow.