• Geotechnical Engineering
• /
• v.14 no.5
• /
• pp.39-52
• /
• 1998

The pupose of the present paper is to estimate the effects of constraint condition of pile head, ground condition(dry unit weight. $\gamma_4$) and embedded pile lengths on the behavior of single pile which is embedded in normally consolidated clay. BBperiment functions can be quantified to these effects obtained from the results of model teats. The ground of model tests is normally consolidated( NC ) clay under three kinds of effective vertical stress. The results of the model tests using the steel pile of two different embedded pile length and of free-head and fired-head show that the lateral load-deflection relationship is to be elasto plastic behavior below $\gamma_d/\gamma_{dmax}$: 0.84 and that the reduction of lateral load of beyond maximum lateral load($Q_{max}$) at each model test is significantly time-dependent. In this study, it is shown that the displacement relationship can be fitted to exponential function of time by model best results. The effect of ground conditions on the ultimate and yield lateral load is fitted to exponential function including the ratio of dry unit weight to maximum dry unit weight. When tests by results are compared with those from Broms and Budhu et at., the predicted results are over-estimated about 27-87 ayo. In effectivity of constraint condition of pile head on the lateral load-deflection response, the $Q_{fixed}/Q_{gree}-y/D$ relationship is highly non-linear and fitted to parabolic function.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.36 no.4
• /
• pp.613-618
• /
• 2009

Impacted molars are not usual with the prevalence rate of less than 1%, however problems such as infraocclusion, extrusion of the opposite tooth and lack of space are caused. If molars are impacted, radiographic check-up and observations are needed as they play an important role in skeletal development and mastication. Causes of impaction are underdevelopment of roots, supernumerary teeth, cysts, odontomas, ankylosis and etc. In our first case, we present impacted molar which was surgically exposed and orthodontically traded. As the developmental state of the root was less than half at first visit, we observed until the root was 2/3 in its length and traction was carried out. The second case is orthodontic traded molar with compleate enucleation of the existing cysts. When trading impacted molars, direct bonding of attachments to the tooth and light continuous forces are recommended so as to ankylosis, external absorption and periodontal attachment loss avoid. Fixed appliances tract the teeth on arch and obtain eruption spaces without patient's cooperation. We report surgically exposed and orthodontically traded molars which resulted in good occlusion and patients satisfaction.

• Asian-Australasian Journal of Animal Sciences
• /
• v.23 no.5
• /
• pp.543-555
• /
• 2010

The objectives of this research were the estimation of genetic parameters and trends for weaning-to-first service interval (WSI), and litter traits in a commercial swine population composed of Landrace (L), Large White (T), LT, and TL animals in Chiang Mai, Northern Thailand. The dataset contained 4,399 records of WSI, number of piglets born alive (NBA), litter weight of live piglets at birth (LBW), number of piglets at weaning (NPW), and litter weight at weaning (LWW). Variance and covariance components were estimated with REML using 2-trait analyses. An animal model was used for WSI and a sire-dam model for litter traits. Fixed effects were farrowing year-season, breed group of sow, breed group of boar (litter traits), parity, heterosis (litter traits), sow age, and lactation length (NPW and LWW). Random effects were boar (litter traits), sow, permanent environment, and residual. Heritabilities for direct genetic effects were low for WSI (0.04${\pm}$0.02) and litter traits (0.05${\pm}$0.02 to 0.06${\pm}$0.02). Most heritabilities for maternal litter trait effects were 20% to 50% lower than their direct counterparts. Repeatability for WSI was similar to its heritability. Repeatabilities for litter traits ranged from 0.15${\pm}$0.02 to 0.18${\pm}$F0.02. Direct genetic, permanent environment, and phenotypic correlations between WSI and litter traits were near zero. Direct genetic correlations among litter traits ranged from 0.56${\pm}$0.20 to 0.95${\pm}$0.05, except for near zero estimates between NBA and LWW, and LBW and LWW. Maternal, permanent environment, and phenotypic correlations among litter traits had similar patterns of values to direct genetic correlations. Boar genetic trends were small and significant only for NBA (-0.015${\pm}$0.005 piglets/yr, p<0.004). Sow genetic trends were small, negative, and significant (-0.036${\pm}$0.013 d/yr, p<0.01 for WSI; -0.017${\pm}$0.005 piglets/yr, p<0.007, for NBA; -0.015${\pm}$0.005 kg/yr, p<0.01, for LBW; -0.019${\pm}$0.008 piglets/yr, p<0.02, for NPW; and -0.022${\pm}$0.006 kg/yr, p<0.003, for LWW). Permanent environmental correlations were small, negative, and significant only for WSI (-0.028${\pm}$0.011 d/yr, p<0.02). Environmental trends were positive and significant only for litter traits (p<0.01 to p<0.0003). Selection based on predicted genetic values rather than phenotypes could be advantageous in this population. A single trait analysis could be used for WSI and a multiple trait analysis could be implemented for litter traits.

• The KIPS Transactions:PartB
• /
• v.13B no.3 s.106
• /
• pp.337-344
• /
• 2006

In this paper, we describe the design and the implementation of word clustering system using a definition of an entry word in the dictionary, called a dictionary definition. Generally word clustering needs various features like words and the performance of a system for the word clustering depends on using some kinds of features. Dictionary definition describes the meaning of an entry in detail, but words in the dictionary definition are implicative or abstractive, and then its length is not long. The word clustering using only features extracted from the dictionary definition results in a lots of small-size clusters. In order to make large-size clusters and improve the performance, we need to transform the features into more general words with keeping the original meaning of the dictionary definition as intact as possible. In this paper, we propose two methods for extending the dictionary definition using ontology. One is to extend the dictionary definition to parent words on the ontology and the other is to extend the dictionary definition to some words in fixed depth from the root of the ontology. Through our experiments, we have observed that the proposed systems outperform that without extending features, and the latter's extending method overtakes the former's extending method in performance. We have also observed that verbs are very useful in extending features in the case of word clustering.

• The Journal of Korean Academy of Prosthodontics
• /
• v.35 no.2
• /
• pp.308-329
• /
• 1997

A lot of the research paper was reported about the result of influence of IMC (Intra-mobile connector) in the IMZ implant placed solely in the alveolar bone, but reports about the effect of IMC on functional load at state of connecting with natural teeth ere rare. The major propose of this study was find the mechanical character of IMC itself by using the finite element analysis program after simulated variance of condition connected with the natural teeth and implant on funcional load. When first and second premolar was lost, IMZ implant was placed with a diameter of 3.3mm and a length of 13mm with IMC in second premolar area. Rigid connection was done and the non-figid connention was located on the female part of the canine abutment and the implant respectively and then both the infraocclusion of $30{\mu}m$ and the non-infraocclusion under the load of 40kg applied to the portion of the natural teeth, the pontic and the implant. The displacement and the stress of it was estimated and analyzed IMC itself of the rigid connection and the non-rigid connection was grouped. The following result were obtained. 1. In all groups, the displacement of Y-axis was greater than that of X-axis and the aspect of displacement showed that IMC was displaced downward and to the center. 2. There was no differences in the displacement of IMC regardless of the connection type. 3. In the displacement of IMC, I 4 was the least, I 1 and I 3 are similar and I 2 was the greatest. 4. There was no differences in the peak value of maximal stress of IMC regardless of the connection type. 5. In the peak value of maximal stress of IMC, I 4 was the least, I 1 and I 3 were similar, and I 2 was the largest.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.6
• /
• pp.507-515
• /
• 2015

This paper proposes a filtering method for effective state vector estimation of highly maneuvering target. It is needed to hit the point called 'sweet spot' to increase the kill probability in missile interception. In paper, a filtering method estimates the length of a moving target tracked by a frequency modulated continuous wave (FMCW) radar. High resolution range profiles (HRRPs) is generated from the radar echo signal and then it's integrated into proposed filtering method. To simulate the radar measurement which is close to real, the study on the properties of scattering point of the missile-like target has been conducted with ISAR image for different angle. Also, it is hard to track the target efficiently with existing Kalman filters which has fixed measurement noise covariance matrix R. Therefore the proposed method continuously updates the covariance matrix R with sensor measurements and tracks the target. Numerical simulations on the proposed method shows reliable results under reasonable assumptions on the missile interception scenario.

• Proceedings of the KOSOMBE Conference
• /
• v.1997 no.11
• /
• pp.511-514
• /
• 1997

The objective of this study is to propose a finite element based design of the dental implant replacing unction and shape of natural teeth. For this, geometric actors were varied to investigate stress distribution of the alveolar bone around dental implant. In this study, the results were obtained based on the theory of linear elastic, with geometrically axisymmetric assumption. Geometric actors determining implant shape are ranged as 0.2mm-0.6mm, 0.04mm-0.1mm, 0.46mm-0.84mm or height of thread, radius of curvature of thread, and pitch, respectively. The stresses in the alveolar bone caused by biting force playa major role in determining implant stability. Especially, the stress concentration in the cortical bone causes bone resorption and finally makes the implant unstable. Therefore, the stress distributions were investigated on the side of the alveolar bone focusing on the area of cortical bone. The maximum von Mises stress was found to increase up to 6% as the height of thread increases, while its value was to decrease to 19% when the radius of curvature increase within the assigned ranges. For the variation of pitch, the larger size of pitch results in greater maximum von Mises stress when the length of the implant under consideration is fixed. The existence of the neck below the shoulder did not affect the stress distribution in the region of alveolar bone. However, the stresses on the side of the implant near the neck were found to be different by 20% approximately. Therefore, the neck can provide the stability of the implant against continuing biting movement. As a conclusion, the finite element based study shows a potential in designing the dental implant systematically.

• The Korean Journal of Applied Statistics
• /
• v.26 no.1
• /
• pp.151-162
• /
• 2013

Due to a growing demand for the second-hand product, especially for the expensive one, the warranty and maintenance policies for such products have been studied to improve the product reliability of late. In this paper we study a periodic maintenance model for the second-hand product which is purchased by the customer at the age of $x$. When purchased, the dealer provides a warranty of a fixed length during which the product is maintained periodically to reduce the failure rate of the product and thus, to improve the reliability after each maintenance is served. If a failure occurs between two successive maintenances, only minimal repair is conducted. As for the warranty policy, we adopt free non-renewing repair action on each failure, in addition to the periodic maintenance service during the warranty period. Thus, under the given warranty policy, all the maintenance and repair costs incurred during the warranty period are charged to the dealer. For the proposed periodic maintenance scheme, we formulate a cost model to evaluate the expected total cost charged to the dealer during the warranty period and derive an optimal upgrade level of the failure rate at each maintenance to minimize the expected total warranty cost from the perspective of the dealer. We also present numerical results for an optimal upgrade level based on the proposed methods.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.478-478
• /
• 2012

Recently, there are many researches in order to increase the deposition rate (D/R) and improve film uniformity and quality in the deposition of microcrystalline silicon thin film. These two factors are the most important issues in the fabrication of the thin film solar cell, and for the purpose of that, several process conditions, including the large area electrode (more than 1.1 X 1.3 (m2)), higher pressure (1 ~ 10 (Torr)), and very high frequency regime (VHF, 40 ~ 100 (MHz)), have been needed. But, in the case of large-area capacitively coupled discharges (CCP) driven at frequencies higher than the usual RF (13.56 (MHz)) frequency, the standing wave and skin effects should be the critical problems for obtaining the good plasma uniformity, and the ion damage on the thin film layer due to the high voltage between the substrate and the bulk plasma might cause the defects which degrade the film quality. In this study, we will propose the new concept of the large-area multi-electrode (a new multi-electrode concept for the large-area plasma source), which consists of a series of electrodes and grounds arranged by turns. The experimental results with this new electrode showed the processing performances of high D/R (1 ~ 2 (nm/sec)), controllable crystallinity (~70% and controllable), and good uniformity (less than 10%) at the conditions of the relatively high frequency of 40 MHz in the large-area electrode of 280 X 540 mm2. And, we also observed the SEM images of the deposited thin film at the conditions of peeling, normal microcrystalline, and powder formation, and discussed the mechanisms of the crystal formation and voids generation in the film in order to try the enhancement of the film quality compared to the cases of normal VHF capacitive discharges. Also, we will discuss the relation between the processing parameters (including gap length between electrode and substrate, operating pressure) and the processing results (D/R and crystallinity) with the process condition map for ${\mu}c$-Si:H formation at a fixed input power and gas flow rate. Finally, we will discuss the potential of the multi-electrode of the 3.5G-class large-area plasma processing (650 X 550 (mm2) to the possibility of the expansion of the new electrode concept to 8G class large-area plasma processing and the additional issues in order to improve the process efficiency.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.39 no.4
• /
• pp.326-336
• /
• 2003

In order to modify the construction of gizzard shad coastal purse seine net with possible to the laborsaving of fishing operation in the coastal small fishing vessels, the model experiments were carried out on the model nets for several conventional nets using in the field and the experimental nets was manufactured as 1/100 and 1/60 of the full scale net. The results obtained are summarized as follows；1. In the case of the conventional net and reduction rate 75% in conventional net with purse line the fishing efficiency decreased, the lead line was upward for the surface and the pursing depth of pursing line was very shallow to 2∼3m. 2. In the case of the net having maximum depth in center part designed in this study, the length of float and lead line was 60% of conventional net, the depth of net was fixed 20m to selvage line of the both of the end and extend gradually with 50m, 40m, 30m to the center. Among the these net, depth of pursing line was 20∼23m for 50m and 7∼15m for 40m, 30m the depth of net. These results were suitable for interception of fish school in fishing ground, but several problems will be caused by the depth and current of fishing ground.