• Korean Chemical Engineering Research
• /
• 제49권6호
• /
• pp.846-850
• /
• 2011

주석과 니켈 나노입자를 함량별로 혼합하여 습식법으로 리튬 이차전지용 복합체 음전극을 제조하고 그 물성과 전기화학적 특성을 조사하였다. 이 음전극은 초기 방전시 최대 700 mAh $g^{-1}$의 우수한 방전용량을 나타내었지만 사이클 특성은 심각한 열화를 보였다. 이것은 나노입자간 단순혼합만으로는 전극판의 기공성과 Ni 성분이 충방전에 따르는 Sn성분의 팽창/수축에 대한 기계적 완충제 역할이 충분하지 않았기 때문이며, 차후 이를 보완하는 나노구조체 Sn-Ni 음전극의 설계와 시험이 필요하다.

• 전기화학회지
• /
• 제2권3호
• /
• pp.123-129
• /
• 1999

리튬이온전지용 $LiCoO_2$ 전극의 super s black 도전재료의 함량에 따른 초기 충방전 특성을 1 mol/l $LiPF_6/EC+DEC(1:3\;by\;w/w)$의 전해액에서 리튬기준전극에 대하여 4.3 V에서 2.0 V의 전위 구간에 대하여 C/4 및 C/2율로 충방전하여 측정하였다. 최초의 충전과정에서 high impedance충전 특성을 보였으며, super s black도전재료를 $3\%w/w$ 사용한 경우, $0.5 mA/cm^2$ 전류밀도의 충전에서 high impedance의 해소에 따라 $3.82\;{\Omega}\;{\cdot}\;g-LiCoCo_2$의 저항 감소를 나타내었으며, $0.728\;{\Omega}{\cdot}g-LiCoCo_2$의 전극저항과 비교하여 약 7배 높은 값을 나타내었다. 제2차 충전에의 high impedance해소는 약 $63\;{\Omega}{\cdot}g-LiCoCo_2$으로서 전극저항의 $12\%$ 정도이며, 제1차 충전의 high impedance해소에 비하여 $1.7\%$의 수준으로 감소하였다. 제1차 충전 및 방전 비용량은 C/4방전율에서 각각 160-161 및 $153\~155mAh/g-LiCoO_2$으로, 쿨롱효율은 $95.4\~96.4\%$였으며, 비가역 비용량은 약 6 mAh/g-$LiCoO_2$였다. 충전종료 지점에서 측정한 비저항은 도전재료 함량 $2\~7\%w/w$범위에서 낮은 값을 나타내어 비가역 비용량 특성의 변화와 일치하였다. 도전재료의 함량 증가에 따라 용량밀도가 감소하였으며, C/4율 방전에서 super s black함량 $2\%w/w$와 $2.9\%w/w$의 도전재료를 사용한 전극의 용량밀도는 각각 447mAh/ml 및 431 mAh/ml였다

• 설비공학논문집
• /
• 제19권12호
• /
• pp.842-849
• /
• 2007

For a $CO_2$ two-stage twin rotary compressor used for heat pump water heater system, changes of $CO_2$ solubility in PAG oil were investigated along the gas passages from the first stage suction to final discharge. Only slight changes in solubility took place in suction chambers for both of the first and second stages, but for compression chambers, solubility variation ranged from 0.115 to 0.136, and from 0.133 to 0.182, respectively for the first and second stages. Calculation of gas flashing in parts of leakage oil flows and of oil contained in control volumes due to solubility changes was conducted and included in gas pressure calculation. For the second stage, gas flashing amounts to around $5%\sim6%$ for most leakage flows. Cooling capacity, compressor input, and COP obtained by calculation were well compared to the experimental results. Effects of operation speed on the compressor performance was also studied: as the shaft speed increased, adiabatic efficiency decreased rapidly due to increased over-compression loss.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제53권10호
• /
• pp.530-538
• /
• 2004

A electromagnetic waves are used for sensing in insulation diagnosis at electric machine or equipment. When it a method, waves are transformed into the FFT(Fast Fourier Transform); a kind of the process for data transformation. In a general way, a scientist use frequncy band 30[㎒]～l[㎓] to applied field. If we are measured high frequency band, we will need to a high capacity hardware. Also a antenna has a fault on atmospheric phenomena, outside environment and the like. In this paper We proposed new method for detecting electric equipment faulty state using only electric voltage which is generally measured in the electric and electronic field. It is called the Partition-FFT The analytic method is this first divide measured voltage waves into equal parts, second each deal with give effect to the FFT, finally each results deal with a graphic method and gather graphic. We are compare Partition-FFT with discharge form by tracking tester. As the result it demonstrated that the Partition-FFT is applicable.

• 전기화학회지
• /
• 제15권3호
• /
• pp.160-164
• /
• 2012

납축전지는 낮은 가격과 가역적인 반응으로 재사용이 가능하고 높은 기전력을 가져 우리 생활에 가장 널리 사용되고 있지만 제한된 사이클 수명을 가지고 있다. 제한된 사이클 수명은 충전과 방전 과정을 거치면서 전극 표면에 형성되는 $PbSO_4$의 재결정 반응인 Sulfation 때문이다. 본 연구에서는 납축전지의 사이클 진행에 따른 전극 표면 변화를 관찰하였고, 납축전지에 펄스 전류를 인가하여 재생한 전극 표면을 관찰하였다. 납축전지는 600 사이클 후 재생 시 초기 용량의 약 84%까지 용량이 회복하는 특성을 관찰하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 C
• /
• pp.1606-1608
• /
• 1997

We have synthesized PPP from benzen by chemical reaction. And then disordered carbon materials were obtained by heating-treating PPP in a nitrogen atmosphere for 1, 4, 8 and 12 hour at $700^{\circ}C$. The carbon prepared by heat treatment showed a broad x-ray diffraction peak around $2{\theta}=20^{\circ}$ having a property of disordered carbon. Carbon electrodes were charged and discharged at a current density of $0.25mA/cm^2$. In the result, PPP-based carbon obtained at $700^{\circ}C$ for 8h showed 605mAh/g of first discharge capacity and had a small hysteresis characteristic.

• Environmental Engineering Research
• /
• 제17권4호
• /
• pp.197-203
• /
• 2012

Phosphorus removal during discharge of wastewater is required to achieve in a very high level because eutrophication occurs even at a very low phosphorus concentration. However, there are limitations in the traditional technologies in the removal of phosphorus at very low concentration, such as at a level lower than 0.1 mg/L. Through a series of experiments, a possible technology which can remove phosphate to a very low level in the final effluent of wastewater was suggested. At first Al, Zn, Ca, Fe, and Mg were exposed to phosphate solution by impregnating them on the surface of activated alumina to select the material which has the highest affinity to phosphate. Kinetic tests and isotherm tests on phosphate solution have been performed on four media, which are Ca-impregnated activated alumina, activated alumina, Ca-impregnated loess ball, and loess ball. Results showed that Ca-impregnated activated alumina has the highest capacity to adsorb phosphate in water. Scanning electron microscope image analysis showed that activated alumina has high void volume, which provides a large surface area for phosphate to be adsorbed. Through a continuous column test of the Ca-impregnated activated alumina it was discovered that about 4,000 bed volumes of wastewater with about 0.2 mg/L of phosphate can be treated down to lower than 0.14 mg/L of concentration.

• Bulletin of the Korean Chemical Society
• /
• 제20권5호
• /
• pp.508-516
• /
• 1999

Polycrystalline powder of LixNi0.85Co0.15O2 was synthesized by pyrolyzing a powder precursor obtained by the PVA-precursor method. Coin cells of lithium-ion rechargeable battery were assembled, whose the cathodes were fabricated from the crystalline powders of LixNi0.85Co0.15O2 synthesized by the method. The effect of synthetic variation on the property of the cell was tested by carrying out 100 consecutive cycles of charge-dis-charge on the cells. The property of the cell was largely influenced by the pyrolysis conditions applied for the synthesis of the LixNi0.85Co0.15O2. Depending on whether the pyrolysis was carried out in standing air or in the flow of dry air, the discharge capacity and cycle-reversibility of the cell varied in large extent. When the powder precursor was pyrolyzed in standing air, a minor phase of lithium carbonate was remained in the LixNi0.85Co0.15O2. The carbon containing powder precursor had to be pyrolyzed in the flow of dry air to eliminate the minor phase. In the flow of dry air, the lithium carbonate in the precursor was eliminated over 500-700。C without any prominent heat event. By controlling the flow of air over the precursor during its pyrolysis, particle size could also be altered. The effect of flowing dry air, during first step pyrolysis or during second step heat treatment, on the property of the cell was discussed.

• 한국수소및신에너지학회논문집
• /
• 제32권4호
• /
• pp.256-262
• /
• 2021

A carbon felt electrode was prepared using ozone and ammonia sequential treatment and applied as an electrode for a vanadium redox flow battery (VRFB). The physical and electrochemical analyses demonstrate that the oxygen groups facilitate nitrogen doping in the carbon felt. Carbon felt (J5O3+NH3), which was subjected to ammonia heat treatment after ozone treatment, showed higher oxygen and nitrogen contents than carbon felt (J5NH3+O3), which was subjected to ammonia heat treatment first and then ozone treatment. From the charging/discharging of VRFB, the J5O3+NH3 carbon felt electrode showed 14.4 Ah/L discharge capacity at a current density of 150 mA /cm², which was 15% and 33% higher than that of J5NH3+O3 and non-activated carbon felt (J5), respectively. These results show that ozone and ammonia sequential treatment is an effective carbon felt activation method to increase the performance of the vanadium redox flow battery.

• 한국세라믹학회지
• /
• 제47권6호
• /
• pp.638-642
• /
• 2010

The spinel material $Li_4Ti_5O_{12}$ has attracted considerable attention as an anode electrode material for many battery applications owing to its light weight and high energy density. However, the real capacity of $Li_4Ti_5O_{12}$ powder as determined by the solid-state method is lower than the ideal capacity. In this study, we investigated the effect of the dopants in M-doped spinel $Ba_xLi_{4-2x}Ti_5O_{12}$(x=0.005, 0.05, 0.1) powders prepared by the solid-state reaction method and used as the anode material in lithiumion batteries. The results confirmed the effect of the Ba and Sr dopants on the powder properties of the spinel $Li_4Ti_5O_{12}$, which exhibited a pure spinel structure without any secondary phase in its XRD pattern. Moreover, the electrochemical properties of the spinel M-LTO materials were investigated using a half cell. The electrochemical data show that cells with anodes made of undoped $Li_4Ti_5O_{12}$ and Ba- and Sr-doped $Li_4Ti_5O_{12}$ have discharge capacities of 97, 130, and 112 mAh/g, respectively, at the first cycle. Moreover, the Ba- and Sr-doped spinel $Li_4Ti_5O_{12}$ demonstrated good properties in the mid-voltage range at 1.55 V, showing stable cyclic voltammogram properties which surpassed those of the same material without Ba or Sr at 1 C after 100 cycles.