• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.2
• /
• pp.79-89
• /
• 2004

The viscous free surface flow around KRISO container ship (KCS) is computed using the finite volume based multi block RANS code, WAVIS developed at KRISO. The free surface is captured with the Level-Set method and the realizable k-$\varepsilon$ model is employed for turbulence closure. The computations are carried out at model scale. For accurate free surface solution and its stable convergence the computations are performed with a suitable grid refinement around the free surface by applying an implicit discretization method based on a finite volume method to the Level-Set formulation. In all computational cases the numerical results agree well with experimental measurements.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.10
• /
• pp.693-698
• /
• 1999

Vacuum interrupters have a special asymmetric electrode structure to generate an magnetic field and consequently to increase the interrupting ability. Accordingly 2-dimensional analysis has a large analysis error because radial flux can not be considered. In this paper, in order to analyse the electric field distribution of a vacuum interrupter with arc shield more accurately, 3-dimensional finite element method(FEM) is used. The induced electric potentials of floating shield was increased with the gap distance, which is because the relative position of shield is closer to the fixed contact so that the capacitance distribution inside interrupter is varied. The calculated results also show that the induced potential of shield causes electric field distortion so that the maximum value of electric field in a vacuum interrupter with arc shield is higher than that without one.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.7
• /
• pp.329-334
• /
• 2005

This paper presents the optimal design for reducing the rotor inertia in order to improve the driving characteristic of BLDC motor for robots. The parallel Genetic Algorithm is performed to rotor inertia minimization in optimal design. Also, velocity profile with finite jerk method is introduced to reduce vibration of BLDC motor. As a result, a torque characteristic is same although rotor inertia is reduced to 2/3 compared with prototype model. And, maximum vibration value is reduced by 63.4[$\%$] according to the application of finite .jerk method.

• Structural Engineering and Mechanics
• /
• v.3 no.4
• /
• pp.391-410
• /
• 1995

The application of adaptive finite element method to dynamic problems is investigated. Both the kinetic and strain energy errors induced by space and time discretization were estimated in a consistent manner and controlled by the simultaneous use of the adaptive mesh generation and the automatic time stepping. Also an optimal ratio of spatial discretization error to temporal discretization error was discussed. In this study it was found that the best performance can be obtained when the specified spatial and temporal discretization errors have the same value. Numerical examples are carried out to verify the performance of the procedure.

• Structural Engineering and Mechanics
• /
• v.26 no.1
• /
• pp.69-86
• /
• 2007

A four-noded plate bending quadrilateral (PBQ4) and an eight-noded plate bending quadrilateral (PBQ8) element based on Mindlin plate theory have been adopted for modeling the thick plates on elastic foundations using Winkler model. Transverse shear deformations have been included, and the stiffness matrices of the plate elements and the Winkler foundation stiffness matrices are developed using Finite Element Method based on thick plate theory. A computer program is coded for this purpose. Various loading and boundary conditions are considered, and examples from the literature are solved for comparison. Shear locking problem in the PBQ4 element is observed for small value of subgrade reaction and plate thickness. It is noted that prevention of shear locking problem in the analysis of the thin plate is generally possible by using element PBQ8. It can be concluded that, the element PBQ8 is more effective and reliable than element PBQ4 for solving problems of thin and thick plates on elastic foundations.

• 전기의세계
• /
• v.30 no.10
• /
• pp.645-654
• /
• 1981

A technique has been proposed for fabricating a submicron channel vertical V-groove JFET using standard photolithography. A finite element numerical simulation of the V-groove JFET operation was performed using a FORTRAN progrma run on a Cyber-174 computer. The numerical simulation predicts pentode like common source output characteristics for the p$^{+}$n Vertical V-groove JFET with maximum transconductance representing approximately 6 precent of the zero bias drain conductance value and markedly high drain conductance at large drain voltages. An increase in the acceptor concentration of the V-groove JFET gate was observed to cause a significant increase in the transconductance of the device. Therefore, as above mentioned, this paper is study on the analysis of a Vertical V-groove Junction Field Effect Transistor with Finite Element Method.d.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1998.06a
• /
• pp.74-82
• /
• 1998

The limit drawing ratio (LDR) is a major process parameter in the process design of deep drawing. If the actual drawing ratio is greater than the LDR for a particular stage, then an intermediate stage has to be added to the process sequence to avoid failure during the ratio. In this study, the optimal process design considering forming limit is performed for the first-drawing and redrawing by using finite element method combined with ductile fracture criterion. The LDR and the site of fracture initiation are predicted by means of the fracture criterion. From the results of finite element analysis, the optimal value of drawing ratio is obtained, which contributes to the more uniform distribution of thickness and the smaller values of the ductile fracture in final cup.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.13 no.3
• /
• pp.1-9
• /
• 1976

A numerical method for solving the boundary-value problem related to potential flows with a free surface and an experimental work are introduced in this paper. The forced heaving motion of cylinders with arbitrary shapes in water of finite depth are Considered here. The Fredholm integral equation of the first kind is employed in determining strengths of singularities distributed on the body surface. And the results obtained by the present method for the case of a heaving circular cylinder on water of finite depth agree well with existing results of earlier investigators.

• Biomaterials and Biomechanics in Bioengineering
• /
• v.3 no.2
• /
• pp.71-84
• /
• 2016

The finite element method is wide used in simulation in the biomechanical structures, but a lack of studies concerning finite element mesh quality in biomechanics is a reality. The present study intends to analyze the importance of the mesh quality in the finite element model results from humeral structure. A sensitivity analysis of finite element models (FEM) is presented for the humeral bone and cartilage structures. The geometry of bone and cartilage was acquired from CT scan and geometry reconstructed. The study includes 54 models from same bone geometry, with different mesh densities, constructed with tetrahedral linear elements. A finite element simulation representing the glenohumeral-joint reaction force applied on the humerus during $90^{\circ}$ abduction, with external load as the critical condition. Results from the finite element models suggest a mesh with 1.5 mm, 0.8 mm and 0.6 mm as suitable mesh sizes for cortical bone, trabecular bone and humeral cartilage, respectively. Relatively to the higher minimum principal strains are located at the proximal humerus diaphysis, and its highest value is found at the trabecular bone neck. The present study indicates the minimum mesh size in the finite element analyses in humeral structure. The cortical and trabecular bone, as well as cartilage, may not be correctly represented by meshes of the same size. The strain results presented the critical regions during the $90^{\circ}$ abduction.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.5 s.98
• /
• pp.604-611
• /
• 2005

The relationship between floor impact sound and vibration has been studied by field measurements, and the vibration modal characteristics have been analyzed. Vibration levels impacted by a standard heavy-weight impact source have been predicted according to the main design parameters using finite element method. Experimental results show that the dominant frequencies of the heavy impact sounds range below 100 Hz and that they are coincident with natural frequencies of the concrete slab. In addition, simple 2-dimensional finite element models are proposed to substitute 2 types of 3-dimensional models of complicated floor structural slabs those by The analytical result shows that the natural frequencies from first to fifth mode well correspond to those by experiments with an error of less than $12\%$, and acceleration peak value iscoincident with an error of less than $2\%$. Using the finite element model. vibration levels areestimated according to the design Parameters, slab thickness, compressive strength, and as a result, the thickness is revealed as effective to increase natural frequencies by $20\~30\%$ and to reduce the vibration level by 3$\~$4 dB per 30 mm of extra thickness.