• 소성∙가공
• /
• 제9권5호
• /
• pp.533-538
• /
• 2000

This study has been carried out to develop a CRT die using hot forging. The conventional CRT die made by casting has defects such as void and inclusion. These defects of the cast die make micro-spots on the surface of the CRT which affect the quality of the final product. So, a hot forging process is developed to avoid these defects of CRT die by the model material test and the rigid-plastic FEM. Firstly, model material tests are carried out with plasticine billets in order to investigate the material flow pattern in the die cavity and to get the reasonable initial values for designing the preform in the FE simulation. And then a finite element analysis has been performed to Predict the preform and the forging load of a CRT die. We also suggest an integrated die-set which combines two die-sets into one die-set to save manufacturing time and cost in case of similar die-size.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1998년도 추계학술대회 논문집
• /
• pp.242-247
• /
• 1998

The conventional closed-die forging processes had been applied to forging of the spur gears. But this type process requires high pressure. The commercial finite element analysis code ANSYS for the stress and elastic deformation of non-axisymmetric die was adopted in this study. In the non-axisymmetric die such as gear forging, maximum stresses were imposed on the tip of the gear tooth. When the stress exceeds yield strength of insert die, many approaches were attemped to prevent the die failure. Good shaped products are forged successfully. This type process could by used as an advanced technique to replace conventional hobbing process of gear.

• 소성∙가공
• /
• 제18권6호
• /
• pp.444-447
• /
• 2009

Piston crown to the hot forge a unified nature of the product has a shape with multi-level step forging process, so if you are not a mechanical professional, this process could lead to a significant loss to the material. Therefore, material technology in minor terms; continue to improve the collection rate that undamaged the product material. The piston crown and the manufacturing products such as marine diesel engines are being forged to reduce costs and to improve mechanical properties. Piston crown molding is a hot forging process that works in large volume forging products. Because of the size of the hard plastic material flow process for improving the design and actual field experience through advanced plastic technology, it is important to interpret the results. Also for many experimental plastic procedures, the accumulation of results is very important.

• 동력기계공학회지
• /
• 제6권3호
• /
• pp.31-35
• /
• 2002

Brake tube is considered one of the most important parts in automobile. The shape of brake tube end has a great influence on the function of brake, and the quality and productivity of brake tube have relation to die design. The forming process of brake tube end is performed by hydraulic press forming machine. In this paper, the forming processes of tube end for automobile is analyzed and designed to make the optimal form of brake tube end. Also, finite element analysis has been carried out using $DEFORM^{TM}% 3D to predict the optimal shape of brake tube end and the results obtained showed the optimal length between punch and chuck is $1.0{\sim}1.2mm$. The shape of tube end is in good agreement with the finite element simulations and the experimental results.

• 소성∙가공
• /
• 제6권4호
• /
• pp.319-328
• /
• 1997

A flow stress involving strain, solid fraction, and breakage ratio, and solid fraction updating algorithm were proposed to depict the deformation behavior of materials at the semi-solid state. In case of isothermally simple upsetting of Sn-15%Pb alloy at the semi-solid state, by comparing the results of finite element analysis with the existing experimental results, the reliability of both the developed flow stress and updating algorithm were investigated. It was found that the verified program can effectively be used in the rigid-viscoplastic finite element analysis of the semi-solid forging processes.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 추계학술대회 논문집
• /
• pp.62-65
• /
• 2000

For saving time and cost of experiment Finite Element Method has been developed for several decades. It's the defect of FEM that when we are in processing of finite element analysis, the material if deformed so much that we can't proceed analysis any more. In this case, the remeshing process should be done on this material. In hot forging process, almost all remeshing process does not consider flash of the material. Because as mesh size become swatter, consuming time become larger. But if mesh size is big, there is the defect that the result of analysis is not so accurate. So, new remeshing algorithm is needed to save time and to get more accurate result.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.113-116
• /
• 2001

Finite element analysis programs have been for metal forming process design They will become more and more important in understanding forming process For large-scale forging analysis problems, the performance of a linear equation solver is very important for the overall efficiency of the analysis code. With problem size increased, the computation time needs to be reduced, which is spent on setting the system of algebraic equations associated with finite element model Many matrix solvers have been developed and used usefully in finite element program for this purpose.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.249-250
• /
• 2013

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.279-280
• /
• 2010

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.84-88
• /
• 2009

The nickel-based alloy Nimonic 80A possesses strength, and corrosion, creep and oxidation resistance at high temperature. The exhaust valves of low speed diesel engines are usually operated at temperature levels of 400-$600^{\circ}C$ and high pressure to enhance thermal efficiency and exposed to the corrosion atmosphere by the exhaust gas. Also, the exhaust valve is subjected to repeated thermal and mechanical loads. So, the nickel-based alloy Nimonic 80A was used for the large exhaust valve spindle. It is composed a 540mm diameter head and a 125mm diameter stem. It is developed large products by hot closed-die forging. Manufacturing process analysis of the large exhaust valve spindle was simulated by closed die forging with hydraulic press and cooled in air after forging. The preform was heated to $1080^{\circ}C$ Numerical calculation was performed by DEFORM-2D, a commercial finite element code. Heat transfer can be coupled with the deformation analysis in a non-isothermal deformation analysis. Mechanical properties of the large exhaust valve spindle were evaluated by the variety of tests, including microstructure observation, tensile, as well as hardness and fatigue tests, were conducted to evaluate the mechanical properties for head part of exhaust valve spindle.