• 한국염색가공학회지
• /
• 제30권1호
• /
• pp.9-19
• /
• 2018

To prepare bio-inspired antifouling coating materials having similar structure with lotus, self-crosslinkable waterborne polyurethanes emulsions containing paraffin wax (CWPU/P0, 0.25, 0.5, 1.0, 1.5, 2.0, the number indicated the wt% of wax) were prepared by an emulsifier-free/solvent free prepolymer mixing process. The as-polymerized CWPU/P emulsions containing 0 - 1.00wt% of paraffin wax were found to be stable after 4 months, however, CWPU/P emulsions containing 1.50 and 2.00wt% of paraffin wax were unstable within 1 month storage. Considering the stability of emulsions, the optimum paraffin wax content was found to be about 1wt% to obtain stable antifouling coating emulsion material. The surface topology of CWPU/P film samples was characterized by atomic force microscopy (AFM). This study examined the effect of paraffin wax content on the surface roughness, water contact angle/surface energy, water swelling, light transmittance and tensile properties of CWPU/P film samples.

• 한국정밀공학회지
• /
• 제23권2호
• /
• pp.199-206
• /
• 2006

Automatic grease lubricator is equipment that provides adequate amount of fresh grease constantly to the shaft and the bearings of machines. It minimizes the friction heat and reduces the friction loss of machines to the least. This research is to develop automatic grease lubricator by gear driven mechanism with controlled operation time. The ultimate design of this equipment is to lubricate an adequate amount of grease by a simple switch clicking according to the advanced set cycle. The backlash of the gear was minimized to increase the output power. To increase the power of gear mechanism, the binding frequency and the thickness of the coil were changed. To control the rotating cycles of the main shaft according to its set numbers, different resistance and chips were used to design the circuit to controls electrical signals with pulse. The body of the lubricator was analyzed by stress analysis with different constructed angle. The stress analysis for differing loading pressures applied to the exterior body of grease lubricator due to the setup angle, was found that the maximum stress was distributed over the outlet part where the grease lubricator suddenly narrowed contracts. Digital mock-up was analyzed and the rapid prototyping(RP) trial products were tested with PCB circuit and grease. The evaluation of the outlet capacity for RP trial products was conducted, because the friction caused by the outlet on the wall surface was an important factor in the operation of the equipment. Finally, the finishing process was applied to decrease the roughness of the surface to a comparable level and was able to test the performance examination for the product.

• 한국염색가공학회지
• /
• 제19권2호
• /
• pp.14-23
• /
• 2007

This research article explores the use of phthalocyanine reactive dye on nylon substrate. The effect of factors such as pH, temperature, liquor ratio and alkali addition on level of dye exhaustion, fixation and total fixation efficiency. Low pH, high temperature and low liquor ratio were found to be suitable conditions for maximum % exhaustion values. The effect of sulphatoethylsulphone(SES) and vinylsulphone(VS) form of the dyes on level of dye fixation was also discussed. The optimized exhaustion (%E), fixation(%F) and total fixation efficiency were determined. Modification of the dyeing process with alkali addition displayed that dye fixation(%) increased by alkali addition. Vinylsulphone(VS) moiety of the dye was found to be superior to. maximum fixation (%F). Appropriate predictable empirical models, relatively a new approach in dyeing processes, were developed incorporating interactions effects of temperature, pH and liquor ratio for predicting % exhaustion, fixation and total fixation efficiency. The significance of the mathematical model developed was ascertained using microsoft excel regression(solver) analysis module. High correlation coefficient was obtained (R2=0.9895 for % exhaustion, R2=0.9932 for fixation, R2=0.9965 for total fixation efficiency) for the model which shows prominent prediction capacity of the model for my conditions. The predictable polynomial equations developed from tile experimental results were thoroughly analyzed by ANOVA (Analysis of Variance) statistical concepts.

• 한국염색가공학회지
• /
• 제26권1호
• /
• pp.22-31
• /
• 2014

This study investigated the physical properties of warm up yarns and their knitted fabrics including the dye affinity and color fastness to washing of these knitted fabrics according to the various dyeing times and temperatures on dyeing process. The results were summarized as follows. The tenacity of Nylon/PP warm-up yarn was 4g/d and breaking strain was 4.5%. The wet and dry thermal shrinkages were higher than those of PET warm-up yarn. The maximum heat flow rate(Qmax) of Nylon/PP warm-up knitted fabric was lower than that of PET warm-up knitted fabric and heat keeping rate(a) of Nylon/PP warm-up knitted fabric was higher as 47% than that of PET warm-up knitted fabric. It was shown that the shape retention and wearing comfort of Nylon/PP warm-up knitted fabric were better than those of PET warm-up knitted fabric. The dye-affinity(K/S) of Nylon/PP warm-up knitted fabric showed maximum value at the dyeing condition of 40minute or 50minute dyeing time with $80^{\circ}C$ dyeing temperature, but PET warm-up knitted fabric showed maximum value at the 30minute or 40minute with $110^{\circ}C$ dyeing temperature. Finally, the color fastness to washing of Nylon/PP warm-up knitted fabric showed good value as between 4 and 5 grade.

• 한국염색가공학회지
• /
• 제18권6호
• /
• pp.16-24
• /
• 2006

The purpose of this study is to improve the defects of chitosan crosslinked viscose rayon by ECH and to describe the change of hand of chitosan crosslinked viscose rayon fabrics. The chitosan crosslinked viscose rayon were manufactured by crosslinking process using ECH as crosslinking agent, 2 wt% aqueous acetic acid as a solvent of chitosan and ECH, and 20 wt% aqueous sodium hydroxide as crosslinking catalyst. Viscose rayon were first immersed in the pad bath of the mixed solution of chitosan and ECH, padded up to 100 wt% wet pick-up on weight of fiber(owf), precured on pin frames at $130^{\circ}C$ for 2 minutes, immersed in NaOH solution and finally wash and dry. Antimicrobial properties of the viscose rayon treated with chitosan were measured by the shake flask C.T.M. 0923 test method with staphylococcus aureus(ATCC 6538) as the microorganism. When the concentration of chitosan was increased chitosan crosslinked viscose rayon's LT, WT, B, 2HB and MIU were increased and G, 2HG, SMD, T and $T_m$ were decreased. On the other hand, WT, EM were decreased and RT was increased at $1{\times}10^{-2}M$ ECH. The optimum condition for crosslinking was that ECH concentration was between $1{\times}10^{-2}M\;and\;5{\times}10^{-2}M$. Antimicrobial effects of rayon fabric treated with chitosan was excellent.

• 한국염색가공학회지
• /
• 제19권4호
• /
• pp.1-9
• /
• 2007

In recent years, the application of digital textile printing has increased. The benefits of using this method include the ease of sampling and the production of printed textiles. However, the production process of digital textile printing differs from that of conventional printing. For successful digital textile printing by ink-jet technology, the pretreatment of fabrics is very important in order to overcome the following problems. Low viscosity ink can spread easily on the textile surface leading to poor resolution. As a result, the combination of ink and pretreatment chemicals is still impractical and consequently most fabrics used in digital textile printing will require a pre treated coating in order to prevent the ink colours from bleeding on the fabric. Research presented in this paper shows some preliminary attempts to establish the relationship between the pre treatment and the digital textile printing quality. Various cotton fabrics were treated with pre treatment agents including ingredients like thickener, alkali and humectant, and then ink spread effect and colour yield of printed fabrics by reactive ink were analysed by using an optical microscope and K/S value. The results show that digital textile printing quality on cotton fabrics can be optimized with appropriate pre treatments.

• 한국염색가공학회지
• /
• 제21권4호
• /
• pp.23-32
• /
• 2009

The objective of this study is to investigate the efficacy of leaf powder colorants as substitutes for traditional indigo dyeing. Leaf powder colorants were prepared by hot air($50^{\circ}C$) and room temperanrre($25^{\circ}C$) drying methods from fresh leaves. The presence of indigo in the leaf powder colorants was confirmed by UV/Visible absorption spectra. All the powder colorants showed broad absorption at 602 nm as same as synthetic indigo. Dyeing was done by reduction method with sodium hydrosulfite and sodium hydroxide. Leaf powder colorants produced blue color on silk fabrics, showing similar color to the one dyed traditionally with fresh juice extract. The powder colorants prepared at room temperature drying were more stable for long term storage than that prepared by hot air drying. Thus, the powder colorants prepared by room temperature drying was reduced and dyed in one-step process without sodium hydroxide in the dyebath for further investigate dyeing properties. K/S value of the fabric dyed without sodium hydroxide was much higher than one dyed with sodium hydroxide. Regardless of the addition of sodium hydroxide, rubbing fastness was fairly good showing above 4 rating. Fastness to dry cleaning and light of the fabrics dyed without sodium hydroxide were mote higher than that dyed in alkaline condition.

• 한국염색가공학회지
• /
• 제29권3호
• /
• pp.171-179
• /
• 2017

This study was to investigate the practicality and functionality of water lily(Nymphaea tetragona) leaves as a natural dye resource while searching for various dyeing methods to utilize them. Effect of dyeing condition including methanol ratio of dyebath, dyeing temperature and time, mordanting method, etc were investigated. Colorants were prepared by extraction in methanol and followed drying process. When composing 30% of methanol in the dyebath, better dyeuptake and uniform dyeing were resulted. Pre-mordanting method gave better results in terms of dye uptake than post-mordanting method on the wool fabrics. Fe and Ti were effective for increasing the dye uptake on the silk fabrics. Depending on mordant type and mordanting method, the dyed fabrics got various color showing green, khaki, brownish yellow, dark brown, dark gray and so on. As for color fastness, the silk fabrics dyed with water lily extract showed relatively high rating in light fastness(3~4, 4~5 rating), washing fastness(4~5, 5 rating), and rubbing fastness(4, 4~5 rating). The silk and wool fabrics dyed with water lily leaves extract showed excellent antimicrobial activity over 98% of bacterial reduction rate against Staphylococcus aureus and Klebsiella pneumoniae. It was confirmed that water lily leaves can be used as a natural dye resource for dyeing wool and silk fabrics because its colorants showed excellent affinity and antimicrobial functionality as well as good colorfastness.

• 복식문화연구
• /
• 제8권1호
• /
• pp.65-76
• /
• 2000

The purposes of this study were to claassify of clothing-wearing motives, to analyze tendency of fashion in campus, and to propose fashion merchandising plans and marketing strategies of companies for female college students. Research had been done during 1 week each on April and October in 1998 and 1999. Sixty-two students in spring semester and 54 student in fall semester were surveyed and analyzed. Their grades and majors were not considered in this study. Fashion Diary had been written by students and then their statements were analyzed by the means of the qualitative data analysis. Following conclusions were obtained from this study. 1. Clothing-wearing motives were classified with 'group depending on daily work', 'group depending on image', 'group depending on body supplement', 'group depending on weather', 'group of fashion following', 'group depending on courtesy', 'group depending on mood', and 'group of unconcerning'. 2. The fashion tendency of the students were layered look and they preferred casual styles, such as round t-shirts, jean pants, and cardigans. The color of white, black, and gray were prevalent for top wear, and the color of blue, black, beige for bottom wear in both seasons. For shoes, color of black, brown, white were popular. For bags, black, blue, and khaki color were prevailed. 3. The proposals obtained from this study are as follows : 1) Production of clothing enforced functional and practical base is wanted for 'group depending on daily work'. 2) Designs considering body parts such as hip, arm hole, shoulder, and thigh are needed. 3) Utilization of new materials such as waterproof with ventilation, opaque (means 'not see-through'), antipollution finishing process are required. 4) Simple designs of clothing which could be performed by herself with various accessories. Thermochromic materials are wanted for 'group of fashion following'. 5) Diversity of semi-suit is required for 'group depending on courtesy'.

• Restorative Dentistry and Endodontics
• /
• 제25권3호
• /
• pp.482-486
• /
• 2000

The purpose of the present study was first, to evaluate the relationship between composite surface conversion and surface discoloration, second, to know if there was difference in surface discoloration between celluloid-strip-finished composite surface and polished surface. In addition, the discoloration of composite surface was also evaluated with visual inspection or digital camera with high resolution monitor, Z100, Tetric Ceram, Spectrum, and Aelitfil were used. The composite surfaces were celluloid-strip finished (group 1), polished (group 2), celluloid-strip finished under nitrogen gas purging (group 3) or only light cured without finishing or polishing under nitrogen gas purging (group 4). The microhardness of each samples were also measured in each group. The samples of each group were also divided into 4 subgroup whether they were immediately placed in disclosing solution (0.2% Elythrosin, pH 7.0) (subgroup1), 1 day after light curing(subgroup 2), 3day after light curing(subgroup 3) or 7 day after light curing(subgroup 4). The computer controlled spectrophotometer was used to determine CIELAB coordinates ($L^*$, $a^*$, $b^*$). The amounts of color difference were compared. The results were as follows; 1. There was no difference in discoloration between celluloid strip finished composite surface and polished surface. 2. The samples discolored more when they were placed in disclosing solution immediately after polymerization than other groups. 3. When the samples were light cured under nitrogen gas purging and without polishing process, they discolored more than other groups even though they showed higher micro hardness. 4. With visual inspection or digital camera, only a limited information was available in detecting composite surface discoloration.