• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.6
• /
• pp.753-759
• /
• 2000

Photoelectric charging is a very efficient way of charging small particles. This method can be applied to combustion measurement, electrostatic precipitator, metal separation and control of micro-contamination. To understand the photoelectric charging mechanism, particle charging of silver by exposure to ultraviolet is investigated in this study. Average charges and charge distributions are measured at various conditions, using two differential mobility analyzers, a condensation nucleus counter, and an aerosol electrometer. The silver particles are generated in a spark discharge aerosol generator. After that process, the generated particles are charged in the photoelectric charger using low-pressure mercury lamp that emits ultraviolet having wavelength 253.7 nm. The results show that ultra-fine particles are highly charged by the photoelectric charging. The average charges linearly increase with increasing particle size and the charge distribution change with particle size. These results are discussed by comparison with previous experiments and proposed equations. It is assumed that the coefficient of electron emission probability is affected by initial charge. The results also show that the charge distribution of a particle is dependent on initial charge. Single changed particle, uncharged particle and neutralized particle are compared. The differences of charge distribution in each case increase with increasing particle size.

• Journal of Korean Society for Atmospheric Environment
• /
• v.19 no.2
• /
• pp.133-143
• /
• 2003

Numerous evidence have been reported that fine particulate matters can play an important role in threatening human health. Recently concerns on fine particle pollution from various engines may require re-examination of particulate emission standards. The particles emitted by most diesel engines are mainly divided into their size ranges such as Dp< 50 nm and 50 nm< Dp< 1,000 nm. In this work, the number concentration and the size distribution of fine particles emitted from an exhaust manifold of a railroad diesel engine were measured under load test conditions using a scanning mobility particle sizer (SMPS). The fine particles observed were within the range of 7 to 304 nm under different load conditions with two different dilution ratios. The fine particles exhibited unique patterns showing bimodal shapes in size distribution.

• Journal of Environmental Science International
• /
• v.7 no.4
• /
• pp.505-510
• /
• 1998

This study has been carried out to investigate Electrostatic Precipitator's(ESP) performance enhancement and removal efficiency of fine particle according to (NH4)2SO4injection rate. The following conclusions are derived from the these test results : 1) For plant condition cases, according to the variation of concentration agent [(NH4)2SO4]-10ppm, when inlet dust loading was 2g/m2. And when Inlet dust loading was 3g/m", that was increased to 98 19% 99.16% 99.23%, 99.58%, 2) It Is seen from thins experiments that the increasing 30ppm concentration of (NH4)2SO4 increase the collection efficiency and fine particle omission control.

• Journal of the Korean Society of Industry Convergence
• /
• v.7 no.1
• /
• pp.115-120
• /
• 2004

An indoor air cleaner consisting of a dielectric barrier discharge system and an electrostatic precipitator (ESP) was experimentally investigated. The function of the dielectric barrier discharge is to precharge particles by producing nonthermal plasma before indoor air enters ESP, leading to an enhancement in dust collection efficiency. The dependence of particle size distribution on the plasma discharge was examined to understand the mechanism of the particle precharging. The plasma discharge was found to increase the electrical force of the particles, rather than agglomerate them. Coarse particles in the range of 0.5 to $5.0{\mu}m$ were observed to be easily collected by this indoor air cleaner, and the present study laid emphasis on the removal of fine particles of $0.3{\mu}m$. The collection efficiency of the fine particles was largely enhanced by the plasma discharge.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2009.05b
• /
• pp.77-80
• /
• 2009

The purpose of the study was to examine engineering characteristics due to fine particle cement and gypsum contents to improve early strength of concrete substituted blast furnace slag powder. The results were as follows. Above all, For fluidity, generally all mixtures had lower fluidity than Plain mixture and was not satisfied target scope, but for mixture substituted the gypsum showed a little increasing trend. For air content, generally all mixtures compared to Plain mixture had decreasing tendency. However, all mixtures were satisfied target scope. For compressive strength, long-term strength was better than early strength according to ternary blast furnace slag contents was increased. For complex mixture was better than individual use of gypsum and fine particle cement.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.16 no.2
• /
• pp.11-22
• /
• 1998

For the purpose of preparation of monodispersed spherical zinc oxide fine particles, an experimental research on the preparation of zinc oxide particles from zinc salts solutions by high temperature precipitation reaction was performed. Zinc oxide particles were precipitated from all the precipitation solutions tested if the precipitation temperature was higher than 60$^{\circ}$. As the precipitation temperature Increased until 80$^{\circ}$, the average particle diameter of zinc oxide particles decreased and the narrower particle size distribution were obtained. Spherical zinc oxide fine particles with relatively narrow particle size distribution were precipitated from the ZnSO$_4$ solutions with NaOH as precipitant. Final pH of precipitation solution had an effect on the amount of zinc oxide precipitated, but had no effect on the their particle size or size distribution.

• Journal of the Korean Ceramic Society
• /
• v.35 no.12
• /
• pp.1308-1315
• /
• 1998

Effects of particle size of alumina on densification behavior during liquid-phase sintering of alumina-talc system were investigated with emphasis on particle rearrangement process. In the case of using coarse alu-mina powder densiication of specimens was rapidly accelerated after formation of liquid phase due to easy particle rearrangement process with addition of talc and increase of sintering temperature. On the contrary when fine alumina powder was used premature densification of alumina matrix region formed before for-mation of liquid phase rigid skeleton structure and then it seemed to inhibit rearrangement process during crease of sintering temperature. As results the densification of specimens using coarse alumina powder was higher than that of the case of using fine one.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.6
• /
• pp.239-243
• /
• 2005

The effect of pH and particle size on the dispersion stability of ultra-fine $BaTiO_3$ suspensions in aqueous medium have been investigated by means of zeta potential, sediment experiments, and powder properties (particle analysis, specific surface area) etc. Zeta potential as a function of pH for two particles of different size increases from -75 to +10 mV with decreasing pH from 8.5 to 1.4. The curve of zeta potential for small particle (150 nm) has slow slope than that of large particle (900nm), giving IEP (isoelectric point) value of pH=1.6 for small particle and pH=1.9 for large particle respectively, which means that it is more difficult to control zeta potential with pH fur small particle than large particle. The dispersion stability of $BaTiO_3$ particles in aqueous medium was found to be strongly related with the agglomeration of colloidal suspensions with time through the sedimentation behaviors of colloidal particles with time and pH value.

• Asian-Australasian Journal of Animal Sciences
• /
• v.22 no.10
• /
• pp.1377-1385
• /
• 2009

Effect of inclusion of hard vs. soft wheat bran with different particle size on diet digestibility, growth performance and some slaughter traits was evaluated in fattening rabbits. Four isonitrogenous and isocaloric diets were used according to the origin of wheat bran (hard (HWB) - Triticum durum - and soft (SWB) - Triticum aestivum) combined with wheat bran particle size sieved by 2 mm (fine: 2) or by 8 mm (coarse: 8) in a bifactorial (2${\times}$2) study. A growth trial was conducted to measure the effect of treatments on performance in one hundred and twenty New Zealand White${\times}$Californian rabbits fed experimental diets from 50 to 87 days of age. Faecal apparent digestibility was determined within the last week in twenty animals per diet. Digestibility of nutrients was higher (p<0.05) in the diet containing HWB2, except for crude protein, ether extract and ash, than fine and coarse soft wheat bran diets. Final live weight, feed intake and feed consumption of rabbits on the diet with fine hard wheat bran were higher and resulted in greater daily weight gains (p<0.01) than for animals on the other diets. The slaughter yield and percentage value of organs were not significantly (p>0.05) affected by the diets fed; however, the diet containing fine hard wheat bran led to lower (p<0.05) percentages of skin, abdominal fat and carcass drip loss than the other dietary treatments. It is concluded that fine hard wheat bran can be better included in the diet than soft wheat bran to maximize growth performance without affecting carcass traits of fattening rabbits.

• Journal of the Korea Concrete Institute
• /
• v.27 no.5
• /
• pp.531-539
• /
• 2015

Properties of normal-strength mortar containing coarsely-crushed coal bottom ash considering standard particle size distribution of fine aggregate were investigated. Mortar containing raw bottom ash was applied as a reference. By crushing the bottom ash with a particle size larger than fine binder but smaller than fine aggregates, i.e., coarse-crushing, water absorption and specific gravity of the particles could be controlled as similar levels to those of natural fine aggregates. Workability and strength of the mortar were not changed and even increased when the coarsely-crushed bottom ash was added considering standard particle size distribution in Standard Specification for Concrete, while those were decreased when raw bottom ash was added without any treatment. When a replacement ratio of coarsely-crushed bottom ash was less than 30 vol.%, there were no significant decrease in dynamic modulus of elasticity and dry shrinkage of the mortar.