• International Journal of Highway Engineering
• /
• v.15 no.5
• /
• pp.101-110
• /
• 2013

PURPOSES : The purpose of this study is to evaluate the durability of ternary blended concrete mixtures adding ultra fine admixture. METHODS : From the literature review, crack was considered as the main distress failure criterion on concrete bridge deck pavement. To reduce the initial crack development due to drying shrinkage, CSA expansion agent and shrink reduction agent were used to ternary blended concrete mixtures as a admixture. Laboratory tests including chloride ion penetration test, surface scaling test, rapid freeze & thaw resistance test, non restrained drying shrinkage and restrained drying shrinkage test were conducted to verify the durability of ternary blended concrete mixtures. RESULTS : Based on the test results, proposed mixtures were verified as high qualified durable materials. Expecially initial drying shrinkage crack was not occurred in ternary blended concrete mixtures with CSA expansion agent. CONCLUSIONS : It is concluded that the durability of proposed ternary blend concrete mixture was acceptable to apply for the concrete bridge deck pavement.

• Computers and Concrete
• /
• v.20 no.2
• /
• pp.165-176
• /
• 2017

Textile Reinforced Cementitious Composite (TRCC) became the most common construction material lately and have excellent properties. TRCC can be employed in the manufacture of thin-walled facade elements, load-bearing integrated formwork, tunnel linings or in the strengthening of existing structures. These composite materials are a combination of matrix and textile materials. There isn't much research done about the usage of polymer modified matrices in textile reinforced cementitious composites. In this study, matrix materials named as fine grained concretes ($d_{max}{\leq}1.0mm$) were investigated. Air entraining effect of polymer modifiers were analyzed and air void content of fine grained concretes were identified with different methods. Aim of this research is to study the effect of polymer modification on the air content of fine grained concretes and the role of defoamer in controlling it. Polymer modifiers caused excessive air entrainment in all mixtures and defoamer material successfully lowered down the air content in all mixtures. Latex polymer modified mixtures had higher air content than redispersible powder modified ones. Air void analysis test was performed on selected mixtures. Air void parameters were compared with the values taken from air content meter. Close results were obtained with tests and air void analysis test found to be useful and applicable to fine grained concretes. Air void content in polymer modified matrix material used in TRCC found significant because of affecting mechanical and permeability parameters directly.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.373-376
• /
• 2008

The objective of this study is to investigate the properties of fresh concrete with recycled fine aggregates. Three different kinds of fine aggregate with natural, high and low quality recycled aggregates were prepared. The concrete mixtures were produced with test parameters of replacement ratio of recycled fine aggregate. The properties of the fresh concrete were measured by means of slump and air content according to elapsed time. Quality control method to maintain the constant total mixing water for recycled aggregate concrete was suggested. The all concrete mixtures were produced with approximately the same slump on the job site after an hour. Test results indicated that compressive strength of the concrete mixtures with constant slump is not affected by the replacement ratio of recycled fine aggregate. Therefore, the practical way for the quality control of recycled aggregate concrete is to maintain the constant total mixing water.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.8
• /
• pp.13-24
• /
• 2011

In the part of geotechnical engineering, soils are classified as either the coarse grained soil or the fine-grained soil following the fine content($F_c$=50%) according to the granularity, and appropriate design codes are used respectively to represent their mechanical behaviour. However, sand-clay mixtures, which are typically referred to as intermediate soils, cannot be easily categorized as either sand or clay. In this study, several monotonic undrained shear tests were carried out on Silica sand fine mixtures with various proportions, and a wide range of soil structures, ranging from one with sand dominating the soil structure to one with fines controlling the behaviour, were prepared using compaction method or pre-consoldation methods in prescribed energy. The shear strength of mixtures below the threshold fines content is observed that as the fines content increases, maximum deviator stress ratio decrease for dense samples while an increase is noted for loose samples. Then, by using the concept of fines content and granular void ratio, the monotonic shear strength of the mixtures was estimated. It was found that the shear behavior of mixtures is greatly dependent on the skeleton structure of sand particles.

• Journal of the Korean GEO-environmental Society
• /
• v.14 no.1
• /
• pp.33-42
• /
• 2013

In this paper, a series of monotonic undrained shear tests were carried out on four kinds of sand-fine mixtures with various fines content. Two kinds of sands (Silica sand V3, V6) and fines (Iwakuni natural clay, Tottori silt) were mixed together in various proportions, while paying attention to the void ratio expressed in terms of sand structure $(F_c{\leq}F_{cth})$. The undrained shear strength of mixtures below the threshold fines content was observed so that as the plastic fines content increases, maximum deviator stress ratio decrease for dense samples while an increase is noted for loose samples. For non-plastic fines, the increase in the amount of fines leads to an increase in density of the soil, which results in an increase in strength. Then, the monotonic shear strength of the mixtures was estimated using the concept of granular void ratio. It was found that the shear strength of mixtures is greatly dependent on the skeleton structure of sand particles.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2009.05b
• /
• pp.77-80
• /
• 2009

The purpose of the study was to examine engineering characteristics due to fine particle cement and gypsum contents to improve early strength of concrete substituted blast furnace slag powder. The results were as follows. Above all, For fluidity, generally all mixtures had lower fluidity than Plain mixture and was not satisfied target scope, but for mixture substituted the gypsum showed a little increasing trend. For air content, generally all mixtures compared to Plain mixture had decreasing tendency. However, all mixtures were satisfied target scope. For compressive strength, long-term strength was better than early strength according to ternary blast furnace slag contents was increased. For complex mixture was better than individual use of gypsum and fine particle cement.

• Geomechanics and Engineering
• /
• v.1 no.2
• /
• pp.169-178
• /
• 2009

Due to the enormous amount of fills required, broken rock-fine grain soil mixtures have been increasingly used in the construction of high-fill foundations for airports, railways and highways in the mountain areas of western China. However, the compressibility behavior of those broken rock-fine grain soil mixtures remains unknown, which impose great uncertainties for the performance of those high-fill foundations. In this research, the mixture of broken limestone and a fine grain soil, Douposi soil, is studied. Large oedometer tests have been performed on specimens with different soil content. This research reveals the significant influence of fine grains on the compressibility of the mixture, including immediate settlement, creep, as well as wetting deformation.

• Journal of the Korean Geotechnical Society
• /
• v.37 no.7
• /
• pp.35-42
• /
• 2021

An experimental study was carried out on kaolinite-sand mixtures with various proportions of kaolinite content. To investigate physical behaviour of mixtures, index properties and compaction test results were analysed in various aspects. Moreover, to clearly see the interaction between kaolinite and sand particles, the observational analysis through microscopic image analysis device was conducted. The test results showed that an increase in the amount of kaolinite could create a strong bonding structure which resulted in higher specific surface available for activities of kaolinite particles. Also, an increase in the amount of the kaolinite resulted in an increase in the percentage of water sorption. Then it could accelerate the occupation rate of water which tended to take up the space that would have been occupied by solid particles, and accordingly, resulted in the decreased maximum dry unit weight and increased initial void ratio. Based on the microscopic image analysis, the samples were individually classified into three types of mixture such as sand dominant, intermediate fine content, and fine dominant. In addition, the fine and coarse grains seem to interact well in the mixtures with the fine content ranging from 25 to 40%.

• Journal of the Korean Ceramic Society
• /
• v.31 no.9
• /
• pp.989-994
• /
• 1994

This study aims at finding the closest packings of regular shape particles such as sphere, circle rod and hexagonal rod type. As the ratio of particle size to container lowered to less than 1/10, the wall effect decreased gradually. The tap density of spherical particles with almost orthorhombic arrangement was 59.5%, while those of circle rod and hexagonal rod type particles were 63.5% and 63.0% respectively. And it was decreased with increasing the aspect ratio of regular particles. The tap density of binary mixtures was larger than that corresponding to the monosized particles packing by about 15%. The tap density of ternary mixtures was larger than that of corresponding to the packing of binary mixtures by about 9%. This work employed the binary mixture of 60% coarse particles and 40% fine particles with size ratio of 1.0 to 1/10 and the ternary mixture of 60% coarse particles, 20% medium and 20% fine particles with size ratio of 1:1/10:1/400 respectively.

• Journal of Adhesion and Interface
• /
• v.15 no.3
• /
• pp.100-108
• /
• 2014

In this work, a series of molar ratios composed with YD-128 and DDM were chosen based on the viscosity analysis. The mixtures of YD-128 and DDM with the different molar ratios were cured at $170^{\circ}C$ for 15 min followed by post cure at $190^{\circ}C$ for two hours. The thermal properties of the cured samples were investigated with DSC, TGA, DMA, and TMA. The conversion ratio of the mixtures of YD-128 and DDM (1 : 1.1) was calculated by dividing ${\Delta}H$ obtained from DSC experiments for each cured sample by ${\Delta}H$. The TGA data of the cured samples showed that the thermal stability and thermal degradation activation energy were proportional to the amount of DDM in the mixtures. However, the highest tan ${\delta}$, and the lowest thermal expansion data with DMA and TMA respectively were obtained from the stoichiometric mixture of YD-128 and DDM. Furthermore, the different ratio of mixtures were applied to test specimens to be cured at $170^{\circ}C$ to measure single lap shear strength with universal testing machine.