• Journal of Magnetics
• /
• 제4권1호
• /
• pp.5-9
• /
• 1999

Effect of sulfur segregation on tertiary recrystallization and magnetic induction during final annealing was investigated in a 3% Si-Fe electrical strip containing 6 ppm(LS) and 15 ppm(HS) sulfur. During final annealing, Auger peak height of segregated sulfur on the surface of the strips reached a maximum, and then decreased to low level with increasing annealing time, which is attributed to sulfur segregation and evaporation. The magnetic induction of the thin-gauged 3% Si strip was inversely proportional to the Auger peak height of segregated sulfur on the surface. The overall profile for surface segregation of sulfur and B10 was observed, irrespective of sulfur content in Si-Fe strips, but the peaks of LS strips appeared earlier than those of HS strips. The grain growth rate of the LS strips during final annealing was faster than that of the HS strips, which may be attributed to the pinning effects of segregated sulfur. With increasing final annealing temperature, B10 value increased rapidly and the saturation level in B10 increased.

• 한국재료학회지
• /
• 제11권10호
• /
• pp.879-888
• /
• 2001

The effects of final annealing temperature on the microstructure and creep characteristics were investigated for the Zr-lNb-0.2X (X=0, Mo, Cu) and Zr-lNb- 1Sn-0.3Fe-0.1X (X=0, Mo, Cu) alloys. The microstructures were observed by using TEM/EDS, and grain size and distributions of precipitates were analyzed using a image analyzer. The creep test was performed at $400^{\circ}C$ under applied stress of 150 MPa for 10 days. The $\beta$-Zr was observed at annealing temperature above $600^{\circ}C$. In the temperature above$ 600^{\circ}C$, the grain sizes of both alloy systems appeared to be increased with increasing the final annealing temperature. The creep strengths of Zr-1Nb-1Sn-0.3Fe-0.1X alloys were higher than those of Zr-1Nb-0.2X ones due to the effect of solid solution hardening by Sn in Zr-lNb-lSn-0.3Fe-0.1X alloy system. Also, Mo addition showed the strong effect of precipitate hardening in both alloy systems. The creep strength rapidly decreased with increasing the annealing temperature up to $600^{\circ}C$. However, a superior creep resistance was obtained in the sample that annealed to have a second phase of $\beta$-Zr. It was considered that the appearance of $\beta$-Zr would play an important role in the strengthening mechanism of creep deformation.

• 열처리공학회지
• /
• 제7권3호
• /
• pp.175-183
• /
• 1994

The effect of batch annealing conditions and austenitizing temperatures on the hardness and microstructural factors were examined by using 420J2 martensitic stainless steel. In spite of the similler hardness after batch annealing, the difference in hardness at the same austenitizing temperature was caused by changes in dissolved carbon during batch annealing. The highest hardness of the specimen was obtained at the batch annealing temperature of $820^{\circ}C$ and austenitizing temperature of $1050^{\circ}C$. The main factor affecting the final hardness of the cold annealed 420J2 specimen was proved to the austenitizing temperature rather than batch annealing temperature.

• 한국재료학회지
• /
• 제11권8호
• /
• pp.647-654
• /
• 2001

Nb 첨가 Zr합금인 Zr-lNb합금과 Zr-lNb-lSn-0.3Fe함금의 석출물 및 산화 특성에 미치는 마지막 열처리 온도의 영향을 알아보기 위하여 최종 열처리 온도를 $450^{\circ}C$에서 $800^{\circ}C$까지 변화시켜 미세조직 및 산화 특성을 조사하였다. 부식 시험은 $400^{\circ}C$ , 수중기 분위기에서 270 일 동안 실시하였으며 X-선 회절법을 이용하여 산화막 결정 구조를 분석하였다. 마지막 열처리 온도가 $600^{\circ}C$ 이상일 때 두 합금 모두 $\beta$-Zr이 관찰되었으며 모두 재결정 이후 마지막 열처리 온도가 상승할수록 석출물의 면적 분율이 증가하는 경향을 나타내었다. 모든 열처리 온도 구간에서 Zr-lNb합금의 부식 저항성이 Zr-lNb-lSn-0.3Fe 합금에 비해 우수하였으며 두 합금 모두 재결정 이후 부식 저항성이 급격히 나빠졌다. 이는 $600^{\circ}C$ 이후 형성된 $\beta$-Zr의 영향으로 밝혀졌다.

• 한국세라믹학회지
• /
• 제32권8호
• /
• pp.881-892
• /
• 1995

Sol-Gel derived ferroelectric PZT thin films were fabricated on ITO/Glass substrate. Two kinds of rapid thermal annealing methods, R-I (six times of intermediate and final annealing) and R-II (one final annealing after six times of intermediate annealing) were used for preparation of multi-coated PZT thin films. 2500$\AA$-thick PZT thin films were obtained by the R-I and R-II methods and characterized by microstructure and dielectric properties. In case of using R-II, the microstructure was finer than that of R-I and there was no distinguishable difference in dielectric properties of PZT thin films between the R-I and R-II methods. But dielectric properties were enhanced by increasing perovskite phase fraction with increasing annealing temperature. Measured dielectric constant of PZT thin film annealed at 62$0^{\circ}C$ using the R-I method was 256 at 1kHz. Its remanant polarization (Pr) and coercive field (Ec) were 14.4$\mu$C/$\textrm{cm}^2$ and 64kV/cm, respectively.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.112-115
• /
• 1999

The effect of intermediate annealing on the texture evolution in I.f steel was investigated by using X-ray texture measurement. After The sample was cold rolled to 80% reduction intermediate annealing was introduced to preform ${\gamma}$-fiber orientation grains in deformed matrix. The annealing time was varied between 30 and 3600 sec, These samples were cold rolled to 90% reduction and full annealed. By intermediate annealing final full annealed samples had very homogeneous ${\gamma}$-fiber orientation resulting in good deep drawability.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 추계학술대회 논문집
• /
• pp.17-20
• /
• 2000

In order to improve the sheet formability of the ferritic stainless steel, the through-thickness textures of the recrystallized sample was modified by means of a thermomechanical treatment. An annealing process between the cold rolling reductions modified the preferred orientations throughout the thickness, which resulted in the modification of the final cold rolling texture as well as the final recrystallization texture. With the help of the modification of the recrystallization texture by the intermediate annealing, improvement of the sheet formability, i.e. an increase of the Lankford value.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2002년도 추계학술발표회요약집
• /
• pp.262.1-262
• /
• 2002

• 열처리공학회지
• /
• 제18권4호
• /
• pp.235-241
• /
• 2005

Thermal creep properties of the advanced zirconium fuel claddings named by HANA alloys which were developed for high burn-up application were evaluated. The creep test of HANA cladding tubes was carried out by the internal pressurization method in temperature range from 350 to $400^{\circ}C$ and in the hoop stress range from 100 to 150 MPa. Creep tests were lasted up to 800 days, which showed the steady-state secondary creep rate. The creep resistance of HANA fuel claddings was affected by final annealing temperature and various factors, such as alloying element, applied stress and testing temperature. From the results the microstructure observation of the samples before and after creep test by using TEM, the dislocation density was increased in the sample of after creep test. The Sn as an alloying element was more effective in the creep resistance than other elements such as Nb, Fe, Cr and Cu due to solute hardening effect of Sn. In case of HANA fuel claddings, the improved creep resistance was obtained by the control of final heat treatment temperature as well as alloying element.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.126-127
• /
• 2008

The effects annealing conditions on the electrical conductions of SOI substrate were studied. The reversible change of resistance and carrier concentration in accordance with the annealing temperature were observed for the first time in SOI substrate. The thermal donors due to interstitial oxygen atoms contribute the change of resistance and carrier concentration. Final1y, we show that the furnace annelaing at $500^{\circ}C$ at final heat treatment stage is effective for eliminate the thermal donor effects in SOI substrate.