• The Journal of the Korea institute of electronic communication sciences
• /
• v.3 no.2
• /
• pp.93-100
• /
• 2008

In this paper, Low Noise Block down converter(LNB) is designed for a Ka-band satellite television receiver only(TVRO) using commercially available MMIC. Designed Low Noise Block down-converter is composed of three stage amplifiers involving input noise matched at first amplification stage, image reject band pass filter, frequency mixer and intermediate frequency amplification. Through LNB Module power budget to obtain gain and attenuation, Optimum LNB devices satisfying Ka-band LNB technical specification are selected. Experimental results of designed Ka-band LNB yields conversion gain of over $58{\pm}1dB$, noise figure of less than 1.5dB and phase noise of -94.6dBc @10KHz.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.881-885
• /
• 2002

This paper presents the performance and the algorithm of a 1/3-octave band spectrum control system. The system is developed to provide various spectrums in a high intensity acoustic chamber. The required spectrum, which usually comes from launch vehicle company, starts from 25Hz band and ends 10kHz band. Automatic spectrum control system is preferred since the system requires short settling time to guarantee the safety of test objects and to reduce the amount of operating gas. The developed system adapted a PCI data-acquisition/signal-generation board installed in a personal computer to implement whole control logic. The control software used three cascade digital Butterworth filters using software. The filers are designed following ANSI S1.11 standard to implement 1/3 octave band filter bank. The graphical user interface of the system guides the user to follow standard operation procedure. The averaged control spectrum showed less than 0.05 dB in every running 1/3-octave band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.5
• /
• pp.426-429
• /
• 2017

For the W-band remote sensing radiometer, direct detection type radiometer receiver is designed. The receiver should be low noise and high gain of 60 dB unlike communication and radar receiver. The W-band radiometer consist of 4-stage low noise, high gain amplifier, band pass filter and square law detector. The developed direct detection receiver show 4 GHz bandwidth, 56 dB gain, and 4,500 mV/mW voltage sensitivity at integrator output port for -20 dBm input power at 94 GHz.

• Information and Communications Magazine
• /
• v.13 no.11
• /
• pp.181-191
• /
• 1996

In this paper we discuss narrow-band interference rejection schemes for spectrum overlay communications where direct sequence spread spectrum (DS/SS) communication system and narrow-band communication systems share the same frequency band. In this case, it is essential to reject the narrow-band signals to guarantee the performance of DS/SS system, while it is not necessarily required to reject the DS/SS signal to recover the narrow-band signal. We discuss several schemes such as time domain processing, frequency domain processing and exploiting the device characteristics to reduce the effect of narrow-band signal on DS/SS communication systems. Furthermore, we suggest a structure of tunable notch filter using gyrator that can easily be customized to ASIC.

• Smart Structures and Systems
• /
• v.16 no.6
• /
• pp.1049-1068
• /
• 2015

In the paper, the authors propose the application of operational deflection shapes (ODS) for the detection of structural changes in technical objects. The ODS matrix is used to formulate the spatial filter that is further used for damage detection as a classical modal filter (Meirovitch and Baruh 1982, Zhang et al. 1990). The advantage of the approach lies in the fact that no modal analysis is required, even on the reference spatial filter formulation and other components apart from structural ones can be filtered (e.g. harmonics of rotational velocity). The proposed methodology was tested experimentally on a laboratory stand, a frame-like structure, excited from two sources: an impact hammer, which provided a wide-band excitation of all modes, and an electro-dynamic shaker, which simulated a harmonic component in the output spectra. The damage detection capabilities of the proposed method were tested by changing the structural properties of the model and comparing the results with the original ones. The quantitative assessment of damage was performed by employing a damage index (DI) calculation. Comparison of the output of the ODS filter and the classical modal filter is also presented and analyzed in the paper. The closing section of the paper describes the verification of the method on a real structure - a road viaduct.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.05a
• /
• pp.310-312
• /
• 2011

In complex noise environment, digital filter is being used to obtain, transport and storage original voice or image signal. Digital filter can be largely separated FIR(Finite duration impulse response) filter and IIR(Infinite duration impulse response) filter. Among FIR filter, window function has characteristic of linear phase and as can be easily set pass-band frequency, cutoff frequency and so on. In this paper, We compared with established method using transient characteristic and peak side-lobe in order to check filter characteristics after we designed the existing variants of the window function.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.11 no.6
• /
• pp.157-162
• /
• 2011

In this study, we design and implement a cavity filter for the Korea T-DMB broadcasting transmitter station and repeater system. HFSS 3 dimensional field simulation tool is used for this study. T-DMB filter has to be high quality factor Q, and cavity filter is applying in T-DMB system due to high handling power. We use HFSS simulation tool for design to obtain exact resonant frequency with easy design. A cavity filter is implemented based on the simulated results, and test results are compared with simulations. Measured resonant frequency and bandwidth are 211.8MHz and 0.1MHz, and correspond with design values.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.418-421
• /
• 2001

The ceramic filters were developed using technology similar to that of quartz crystal and electromechanical filter. However, the key to this development involved the theoretical analysis of vibration modes and material improvements of piezoelectric ceramics. The primary application of ceramic filters has been for consumer-market use. Accordingly, a major emhpasis has involved mass production technology, leading to low-priced devices. A typical ceramic filter includes monolithic resonators and capacitors packaged in unique configurations. Nakazawa developed a double-mode resonator as two acoustically coupled single resonators. And he developed 10.7MHz crystal filters using multi-energy trapping mode of thickness shear vibration. He succeeded in realizing a two-pole band pass filter response without external inductance by splitting a dot electrode to creat coupled symmetric and antisymmetric vibration modes. Accordingly, the simulation for ceramic filter were important. So that, this paper were investigated the pass frequency of filter on the electrode length and thickness of ceramic.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.10 no.6
• /
• pp.91-97
• /
• 2011

In this study, we design and implement a cavity filter for the Korea T-DMB broadcasting transmitter station and repeater system. HFSS 3 dimensional field simulation tool is used for this study. T-DMB filter has to be high quality factor Q, and cavity filter is applying in T-DMB system due to high handling power. We use HFSS simulation tool for design to obtain exact resonant frequency with easy design. A cavity filter is implemented based on the simulated results, and test results are compared with simulations. Measured resonant frequency and bandwidth are 211.8MHz and 0.1MHz, and correspond with design values.

• Proceedings of the IEEK Conference
• /
• 2000.11a
• /
• pp.397-400
• /
• 2000

Telecommunication system demands for increased bandwidths and operating frequencies for analog signal processing could be satisfied in the near future by the emergence of a novel technology based on magnetostatic waves propagating in low loss ferrimagnetic films. The magnetostatic wave is the only available technology for analog signal processing directly at millimeter wave frequencies. This paper has been studied the design and implementation of a Magnetostatic Surface Wave band-pass filter for LMDS system.