• Journal of Biosystems Engineering
• /
• v.33 no.4
• /
• pp.217-223
• /
• 2008

In this study, a garlic clove planter which is capable of planting holes in soil and planting a clove at the same time was designed and tested for film mulched beds. Planting characteristics of the planter were measured through field experiment. Some characteristics were analyzed with multibody dynamic simulation software. Simulation was performed on opening time of the planting hopper. Measured characteristics were position, angle, and reposition amount of garlic in sowing hole. Experiment results showed that the planted position of garlic in planting was 23.0 mm from the hole wall. The reposition amount of garlic was varied with its position and angle when the planted garlic was pressed by an angled compaction wheel. In case of type II position, the position movement of garlic was larger than type I. Average position movement of type II was 11.5 mm at $20^{\circ}$ of compaction wheel angle. These data suggest that cutting diameter of film opening must be larger than 33 mm to provide enough space for garlic sprouting. Also, simulation results showed that the maximum opening time of the planting hopper was 0.26 second.

• Applied Science and Convergence Technology
• /
• v.26 no.2
• /
• pp.34-41
• /
• 2017

A 2.45 GHz microwave plasma with linear antenna has been prepared for hydrophobic and wear-resistible surface coating of carbon steel. Wear-resistible properties are required for the surface protection of cutting tools and achieved by depositing a hydrogenated amorphous carbon film on steel surface through linear microwave plasma source that has $TE_{10}-TEM$ waveguide. Compared to the existing RF plasma source driven by 13.56 MHz, linear microwave plasma source can easily generate high density plasma and provide faster deposition rate and wider process windows. In this study, $Ar/CH_4$ gas mixtures are used for hydrogenated amorphous carbon film deposition. When microwave power of 1000 W is applied, 40 cm long uniform $Ar/CH_4$ plasma could be obtained in gas pressure of 200~400 mTorr. The Vickers hardness measurement of hydrogenated amorphous carbon film on steel surface was evaluated. It was found the optimized deposition condition at $Ar:CH_4=25:25$ sccm, 300 mTorr with microwave power of 1000W and RF bias power of 100W. By deposition of hydrogenated amorphous carbon film, contact angle on steel surfaces increases from $43.9^{\circ}$ to $93.2^{\circ}$.

• Journal of Adhesion and Interface
• /
• v.19 no.4
• /
• pp.154-162
• /
• 2018

Plasma treatment and corona treatment have been used for surface modification of polydimethylsiloxane (PDMS) film by activating its surface with the -OH group. Adhesion promoter or coupling agent was also used to improve adhesion of PDMS film with various materials. However, obtained hydrophilicity onto the surface of PDMS films with those processes was transient and vulnerable. In this study, a new alkoxysilane-functionalized acrylic polymer precursor was first synthesized by copolymerization process, and then was reacted with HO-terminated PDMS through condensation reaction to prepare a new surface modifier for PDMS film. The structure and molecular weight of the prepared surface modifier were confirmed by 1H-NMR and GPC measurement. Surface properties of surface modifier-coated PDMS films were also investigated by using XPS, ATR and WCA analysis. The adhesion between the PDMS film and the surface modifier was tested using cross-cut test.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.216-219
• /
• 2005

In recent, LCD becomes one of the main display devices and expected to have quite good market share during the next couple of years. The demand for low cost and high performance, however, is becoming severe as the competition among other display devices like PDP, OLED increases. To satisfy this demand from market, we need to optimize the parts or modules of the LCD, reduce the number of the assemble and enhance the process for the high brightness and uniformity of the LCD. The LCD consists mainly of LCD panel and Backlight unit(BLU). BLU, which takes big portion of the cost for LCD, consists of light source, light guide panel and many kinds of functional film. Recently light guide panel or film for BLU has micro patterns on its surface and consequently to reduce the number of parts and enhace the brightness and its uniformity. In this study, some methodologies for the fabrication of the master/stamper and molding the light quide panel are introduced for 50um pitch of prizm patterned substrate. Mechanical machining process is adapted and optimized to fabricate micro patterned stamper using the micro cutting tool. Injection molding technology is also developed to obtain uniformly replicated micro patterned products.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.4
• /
• pp.96-101
• /
• 2011

The thin films of TiN have been used extensively as wear-resistant materials, for instance, such as tools of high-speed cutting, metal mold forming etc. In these days, because the thin films capable of being used more severe conditions are needed, the technologies of arc ion plating are tried to improve its characteristics. The purpose of this study is to investigate the characteristics of thin films of (Ti,Cr)N compared with those of TiN. The method of arc ion plating, which is known as showing good tight-adherence and productivity, was used. After manufacturing thin films of ($Ti_{1-x}Cr_{x}$)N (x=0~1) with change of Cr in (Ti,Cr) target, atomic concentration, structure, size of crystallite, residual stress and surface roughness of thin films on substrate were investigated. As the results, it was confirmed that Cr atomic concentrations of thin films were proportionally changed with Cr atomic concentrations of target, and thin films of ($Ti_{1-x}Cr_{x}$)N (x=0~1) showed NaCl type and CrN existed as solid solution to TiN.

• Architectural research
• /
• v.20 no.2
• /
• pp.35-43
• /
• 2018

This article explores the complex modes of experiencing the modern city that are engaging and disengaging by nature, which thus negates any simple ways of understanding what it means by 'the urban' in a Manichean comparison. What follows is an in-depth case study of Gordon Matta-Clark's 1976 film titled City Slivers. Influenced by the countercultural practices prevalent in the 1960s and 1970s, Matta-Clark produced a number of works roughly grouped together under the rubric of "building cuts." Among many others, City Slivers is distinctive among Matta-Clark's extensive cutting projects, in the sense that he actively utilizes film as a primary expressive medium and poetically reassembles fragmentary images of cityscape in order to bring forth an alternative urban scenario where the tension between institution-bound urbanization and dispersed daily urban practices is highlighted. Instead of simply being critical against the changing urban conditions of Manhattan in the 1970s, Matta-Clark aims to actively grasp ambivalent instances of urban life that are at once attractive and alienating, thereby excavating the subconscious terrain of contemporary urbanism that is prevalent but often dismissed over glamorous urban projects.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.203-206
• /
• 2008

In this study, we focused on development of the adhesive insulator using the case for solid rocket motors. Material of insulator used unvulcanized rubber based on EPDM/kevlar. In case of front insulator, preforms was made by using hot press molding, and then modified nylon film was inserted between two preforms for boots manufacturing. Rear insulator included cylinder part was embodied by only one mold with special designed and manufactured shape in the process. Boots part of rear insulator was obtained by cutting machine with hard-metal cemented carbide.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.37 no.2
• /
• pp.117-122
• /
• 1992

This experiment was conducted to determine tuber yield increase of Konjac by sowing time, seed tuber split method and cultural methods. Tuber yield per unit area was generally increased in early planting than conventional planting time. Tuber yield of polyethylene film mulching culture among storage methods was high, while the emergence rate of konjac for seedling plus PE mulching, and tunnel culture were prompted by 20 days, and especially seedling was to be greatly controlled due to temperature difference of the day and night at emergence. All of the cutting methods(two and four split method) were higher than conventional method because of increasing number of bulblet, accordingly, that method using seed tuber was profitable for mass propagation. Both botanical characteristics and tuber yield tend to be increased at 30 to 50 percent shading than natural condition.

• Journal of the Korean institute of surface engineering
• /
• v.54 no.3
• /
• pp.133-138
• /
• 2021

Ternary Ti-X-N coatings, where X = Al, Si, Cr, O, etc., have been widely used for machining tools and cutting tools such as inserts, end-mills, and etc. Ti-Al-N-O coatings were deposited onto silicon wafer and WC-Co substrates by a cathodic arc evaporation (CAE) technique at various negative substrate bias voltages. In this study, the influence of substrate bias voltages during deposition on the microstructure and mechanical properties of Ti-Al-N-O coatings were systematically investigated to optimize the CAE deposition condition. Based on results from various analyses, the Ti-Al-N-O coatings prepared at substrate bias voltage of -80 V in the process exhibited excellent mechanical properties with a higher compressive residual stress. The Ti-Al-N-O (-80 V) coating exhibited the highest hardness around 30 GPa and elastic modulus around 303 GPa. The improvement of mechanical properties with optimized bias voltage of -80 V can be explained with the diminution of macroparticles, film densification and residual stress induced by ion bombardment effect. However, the increasing bias voltage above -80 V caused reduction in film deposition rate in the Ti-Al-N-O coatings due to re-sputtering and ion bombardment phenomenon.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.10
• /
• pp.665-670
• /
• 2016

Prevailing dissemination of machine tools and cutting technology have caused drastic developments of high speed dry machining with work materials of high hardness, and demands on the high-hardness-materials with high efficiency have become increasingly important in terms of productivity, cost reduction, as well as environment-friendly issue. Addition of Si to TiAlN has been known to form nano-composite coating with higher hardness of over 30 GPa and oxidation temperature over $1,000^{\circ}C$. However, it is not easy to add Si to TiAlN by using conventional PVD technologies. Therefore, Ti-Al-Si-N have been prepared by hybrid process of PVD with multiple target sources or PVD combined with PECVD of Si source gas. In this study, a single composite target of Ti-Al-Si was prepared by powder metallurgy of MA (mechanical alloying) and SPS (spark plasma sintering). Properties of he resulting alloying targets were examined. They revealed a microstructure with micro-sized grain of about $1{\sim}5{\mu}m$, and all the elements were distributed homogeneously in the alloying target. Hardness of the Ti-Al-Si-N target was about 1,127 Hv. Thin films of Ti-Al-Si-N were prepared by unbalanced magnetron sputtering method by using the home-made Ti-Al-Si alloying target. Composition of the resulting thin film of Ti-Al-Si-N was almost the same with that of the target. The thin film of Ti-Al-Si-N showed a hardness of 35 GPa and friction coefficient of 0.66.