• Nuclear Engineering and Technology
• /
• 제53권9호
• /
• pp.3051-3057
• /
• 2021

The concrete is considered as an important radiation shielding material employed widely in nuclear reactors, particle accelerators, laboratory hot cells and other different radiation sources. The present research is dedicated to the shielding properties study of the ordinary concrete reinforced with different weight fractions of lead oxide micro/nano particles. Lead oxide particles were fabricated by chemical synthesis method and their properties including the average size, morphological structure, functional groups and thermal properties were characterized by XRD, FESEM-EDS, FTIR and TGA analysis. The gamma ray mass attenuation coefficient of concrete composites has been calculated and measured by means of the Monte Carlo simulation and experimental methods. The simulation process was based on the use of MCNP Monte Carlo code where the mass attenuation coefficient (μ/ρ) has been calculated as a function of different particle sizes and filler weight fractions. The simulation results showed that the employment of the lead oxide filler particles enhances the mass attenuation coefficient of the ordinary concrete, drastically. On the other hand, there are approximately no differences between micro and nano sized particles. The mass attenuation coefficient was increased by increasing the weight fraction of nanoparticles. However, a semi-saturation effect was observed at concentrations more than 10 wt%. The experimental process was based on the fabrication of concrete slabs filled by different weight fractions of nano lead oxide particles. The mass attenuation coefficients of these slabs were determined at different gamma ray energies using ²²Na, ¹³⁷Cs and ⁶⁰Co sources and NaI (Tl) scintillation detector. The experimental results showed that the HVL parameter of the ordinary concrete reinforced with 5 wt% of nano PbO particles was reduced by 64% at 511 keV and 48% at 1332 keV. Reasonable agreement was obtained between simulation and experimental results and showed that the employment of nano PbO particles is more efficient at low gamma energies up to 1Mev. The proposed concrete is less toxic and could be prepared in block form instead of toxic lead blocks.

• 대한화학회지
• /
• 제54권5호
• /
• pp.594-602
• /
• 2010

반도체의 경박단소화, 고밀도화에 따라 향후 반도체 패키지의 주 형태는 CSP(Chip Scale Package)가 될 것이다. 이러한 CSP에 사용되는 에폭시 수지 시스템의 흡습특성을 조사하기 위하여 에폭시 수지 및 충전재 변화에 따른 확산계수와 흡습율 변화를 조사하였다. 본 연구에 사용된 에폭시 수지로는 RE-304S, RE-310S, 및 HP-4032D를, 경화제로는 Kayahard MCD를, 경화촉매로는 2-methyl imidazole을 사용하였다. 충전재 크기 변화에 따른 에폭시 수지 성형물의 흡습특성을 조사하기 위하여 충전재로는 마이크로 크기 수준 및 나노 크기 수준의 구형 용융 실리카를 사용하였다. 이러한 에폭시 수지 성형물의 유리전이온도는 시차주사열량계를 이용하여 측정하였으며, 시간에 따른 흡습특성은 $85^{\circ}C$ and 85% 상대습도 조건하에서 항온항습기를 사용하여 측정하였다. 에폭시 수지 성형물의 확산계수는 Ficks의 법칙에 기초한 변형된 Crank 방정식을 사용하여 계산 하였다. 충전재를 사용하지 않은 에폭시 수지 시스템의 경우, 유리전이온도가 증가함에 따라 확산계수와 포화흡습율이 증가 하였으며 이는 유리전이온도 증가에 따른 에폭시 수지 성형물의 자유부피 증가로 설명하였다. 충전재를 사용한 경우, 충전재의 함량 증가에 따라 유리전이온도와 포화흡습율은 거의 변화가 없었으나, 확산계수는 충전재의 입자 크기에 따라 많은 변화를 보여주었다. 마이크로 크기 수준의 충전재를 사용한 경우 확산은 자유부피를 통하여 주로 이루어지나, 나노 크기 수준의 충전재를 사용한 에폭시 수지 성형물에서는 충전재의 표면적 증가에 따른, 수분 흡착의 상호작용을 통한 확산이 지배적으로 이루어진다고 판단된다.

• 한국정밀공학회지
• /
• 제23권8호
• /
• pp.100-107
• /
• 2006

The objective of this research is to investigate the electromagnetic interference(EMI) shielding characteristics of fiber reinforced composites. We fabricated glass and carbon fiber reinforced composites filled with metal powder and nano carbon black. The measurements of shielding effectiveness(SE) were carried out frequency range 300MHz - 1GHz for commercial purposes such as electric or telecommunication devices. The return loss and loss due to absorption were also measured as a function of frequency in the micro wave(300MHz-1GHz) region. It is observed that the SE of the composites is the frequency dependent, increase with the increases in filler loading. The Mg metal powder filled composite showed higher SE compared to that of carbon black. The Mg metal powder/epoxy composite was shown to exhibit up to 40dB of SE. The results indicates that the composite having higher filler loading can be used for the purpose of EMI shielding as well as for some microwave applications.

• Nuclear Engineering and Technology
• /
• 제53권12호
• /
• pp.4142-4149
• /
• 2021

In the radiation protection application, the metal-polymer composites have been developed for their radiation shielding properties. In this research, the elastomer composites doped by 10 ㎛ and 100nm size of lead, bismuth and tungsten particles as filler with 30 and 60 wt percentages were prepared. To survey the shielding properties of the polymer composites using gamma-ray emitted from 152Eu and 137Cs sources, the gamma flux was measured by using NaI(Tl) detector, then the linear attenuation coefficient was calculated. Also, the Monte Carlo simulation (MCs) method was used. The results showed a direct relationship between the linear attenuation coefficients of the absorbent and filler ratio. Also, the decrease in the particle size of the shielding material in each weight percentage improved the radiation shielding features. When the dimension of the particles was in the order of nano-size, more attenuation was achieved. At low energies used for medical diagnostic X-ray applications due to the predominance of the photoelectric effect, bismuth and lead were suitable selection as filler.

• Advances in concrete construction
• /
• 제7권3호
• /
• pp.143-150
• /
• 2019

This study presents the fracture properties of nano modified medium strength concrete (MSC). The nano particle used in this study is nano silica which replaces cement about 1 and 2% by weight, and the micro steel fibers are added about 0.4% volume of concrete. In addition to fracture properties, mechanical properties, namely, compressive strength, split tensile strength, and flexural strength of nano modified MSC are studied. To ensure the durability of the MSC, durability studies such as rapid chloride penetration test, sorptivity test, and water absorption test have been carried out for the nano modified MSC. From the study, it is observed that significant performance improvement in nano modified MSC in terms of strength and durability which could be attributed due to the addition pozzolanic reaction and the filler effect of nano silica. The incorporation of nano silica increases the fracture energy about 30% for mix without nano silica. Also, size independent fracture energy is arrived using two popular methods, namely, RILEM work of fracture method with $P-{\delta}$ tail correction and boundary effect method. Both the methods resulted in nearly the same size-independent $G_F$ irrespective of the notch to depth ratio of the same specimen. This shows evidence that either of the two procedures could be used in practice for analysis of cracked concrete structures.

• Journal of Ceramic Processing Research
• /
• 제13권spc2호
• /
• pp.332-335
• /
• 2012

A molded transformer is maintenance-free, which makes it unnecessary to replace the insulating material, like in an oil-filled transformer, because the epoxy, which is a molded insulating resin, does not suffer variations in its insulating performance for heat cycles over a long time, as compared to insulating oil. In spite of these advantages, a molded transformer may still be accessed by the user, which is not good in regards to reliability or noise compared to the oil transformers. In particular, a distrust exists regarding reliability due to the long-term insulating performance. These properties have been studied in regards to the improvement of epoxy composites and molded transformer insulation. There have nevertheless been insufficient investigations into the insulation properties of epoxy composites. In this study, it is a researching of the epoxy for insulating material. In order to prepare the specimens, a main resin, a hardener, an accelerator, and a nano/micro filler were used. Varying amounts of TiO2 and ZnO nano fillers were added to the epoxy mixture along with a fixed amount of micro silica. This paper presents the DC insulation breakdown test, thermal expansion coefficient, and thermal conductivity results for the manufactured specimens. From these results, it has been found that the insulating performance of nano/micro epoxy composites is improved as compared to plain molded transformer insulation, and that nano/micro epoxy composites contribute to the reliability and compactness of molded transformers.

• 펄프종이기술
• /
• 제46권4호
• /
• pp.1-10
• /
• 2014

In papermaking industry, inorganic fillers are widely used for the purpose of improving opacity, brightness, printability, uniformity and dimensional stability. They are also useful for production costs and energy savings. In the past, inorganic fillers in papermaking industry only focused on micro-scale but recently, new trials on nano-powdered technology are applying. Even nano-powdered fillers are rapidly utilized for improving the optical and surface properties in coating and surface sizing, there still have some problems in wet-end process due to poor dispersibility and retention. In this study, nano-particled calcium carbonate was produced by milling the PCC and its applicability between micro sized and nano sized calcium carbonated was compared in wet-end process, and finally the sheet properties were evaluated. Nano-PCC was not retained in sheet structure without applying retention system, but with retention system nano-powdered PCC was absorbed on fiber surface with expanding the fiber networks. The application of PAM-bentonite system has resulted in high ash retention and bulky structure for copier paper, and good optical properties in brightness and opacity. However, it required to solve the weakness of low tensile property due to interruption of hydrogen bonding by nano fillers.

• 한국건설순환자원학회논문집
• /
• 제2권4호
• /
• pp.297-306
• /
• 2014

Recently nano-materials are gaining more importance in the construction industry due to its enhanced energy efficiency, durability, economy, and sustainability. Nano-silica addition to cement based materials can control the degradation of the fundamental calcium-silicate-hydrate reaction of concrete caused by calcium leaching in water as well as block water penetration and therefore lead to improvements in durability. In this paper, the influence of synthesized nano silica from locally available rice husk on the mechanical properties and corrosion resistant properties of OPC (Ordinary Portland Cement) has been studied by conducting various experimental investigations. Micro structural properties have been assessed by conducting Scanning Electron Microscopy, Thermo gravimetry and Differential Thermal Analysis, X-Ray Diffraction analysis, and FTIR studies. The experimental results revealed that NS reacted with calcium hydroxide crystals in the cement paste and produces Calcium Silicate Hydrate gel which enhanced the strength and acts as a filler which filled the nano pores present in concrete. Hence the strength and corrosion resistant properties were enhanced than the control.

• Advances in materials Research
• /
• 제12권3호
• /
• pp.227-242
• /
• 2023

Polyester composites play a vital role in civil engineering applications, especially in bridge and car park structures. Therefore, the addition of waste silica-based fillers will both improve the mechanical and durability performance of composites and produce an environmentally friendly material. In this study, the mechanical performance of polyester composites was investigated experimentally and numerically by adding micro and nano-sized silica-based fillers, marble powder, silica fume and nano-silica. 24 cubes for the compression test and 18 prisms for the flexural test were produced in six different groups containing 30% marble powder, 5% silica fume and 1% nano-silica by weight. SEM/EDS testing was used to investigate the distribution of filler particles in the matrix. Experimentally collected results were used to validate tests in the Abaqus software. Additionally, the Extended Finite Element Method (XFEM) was used to estimate the fracture process for the flexural test. The results show that the added silica fume, marble powder and nano silica improves the compressive strength of polyester composites by 32-38% and the flexural tensile strength by 10-60% compared to pure polyester composite. The numerically obtained results matched well with the experimental data, demonstrating the accuracy and feasibility of the calibrated finite element model.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2003년도 International Meeting on Information Display
• /
• pp.771-774
• /
• 2003

The mechanical properties of barrier ribs in PDP require quantification in order to control the defects and to increase the yield in the process. Several different types of rib materials were tested for hardness (H) and Young's modulus (E) with a microtip indenter (Berkovich type). For the assessment of fracture toughness of the rib, a macro Vikers indenter was used. The materials with 30wt% of filler were fired at between $490^{\circ}C$ and $570^{\circ}C$. As a result, the composite became fully densified at $520^{\circ}C$, which is near the T s (Littleton softening point) of glass frit. As the filler content increased, the fracture toughness also $(K_{IC})$ increased in the range of 0.60 to 2.63 $MPa{\cdot}m^{0.5}$ after sintering at $550^{\circ}C$. The results suggest that the application of a nano-indenter would be useful for testing the mechanical properties of barrier ribs.