• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.423-423
• /
• 2012

Recently, many researchers made progress in various studies improving the efficiency of dye-sensitized solar cell. In this paper, we used glass textured by wet-chemical etching process for improvement of photocurrent density in dye-sensitized solar cells. This is owing to increase coefficient of light utilization. Consequently, DSSC using the textured glass exhibit a Jsc of 9.49 mA/$cm^2$, a Voc of 0.73 V and a fill factor (FF) of 0.67 with an overall conversion efficiency of 4.64. This result showed increasing of 20% current density and 16% conversion efficiency using the textured glass. These results suggested that glass texturing was very effective in controlling the light-scattering properties into the photovoltaic cell.

• Current Photovoltaic Research
• /
• v.6 no.2
• /
• pp.56-61
• /
• 2018

In this study, CIGS absorber layers were deposited on low-alkali glass and sodalime glass substrates and potasium floride (KF) of various thicknesses was supplied at an elevated temperature after the CIGS growth. The effect of KF post-deposition treatment on the two types of substrates was extremely different. On the low-alkali substrate, the open-circuit voltage (Voc) was improved but the fill-factor (FF) degradation was severe, whereas the sodalime substrate showed Voc deterioration and FF improvement. In the case of supplying 20 nm of KF on both substrates, the efficiency gain of 0.3~1.1%p was obtained. With increasing the KF thickness, a small protrusion-like microstructure developed on the surface of the absorber layer, and the microstructures that were not removed in the subsequent process were found to be the main cause of the FF loss.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.5
• /
• pp.290-294
• /
• 2018

The shingled photovoltaic module can be produced by joining divided solar cells into a string of busbarless structure and arranging them in series and parallel to produce a module, in order to produce a high output per unit area. This paper reports a study to optimize solar cell electrode structure for shingled photovoltaic module fabrication. The characteristics of each electrode structure were analyzed according to the simulation program as follow: 80.62% fill factor in the six-junction solar cell electrode structure and 19.23% efficiency in the five-junction electrode structure. Therefore, the split electrode structure optimized for high-density and high-output shingled module fabrication is the five-junction solar cell electrode structure.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.7
• /
• pp.4925-4929
• /
• 2015

Dye-sensitized solar cell(DSSC) has aroused intense interest owing to its competitive price and stabilized properties than Si based solar cells. Recently, many studies have been reported on the DSSC, especially development of a transparent conductive oxide-less dye-sensitized solar cell(TCO-less DSSC). In this paper, a thick and porous Ti electrode for low cost DSSC developed its properties. To estimate the Ti electrode, the films are tested FESEM and J-V evaluation method. An increase in Ti thickness from 50 nm to 200 nm mainly affects the fill factor without noticeably changing the photocurrent density. It was confirmed that optimal DSSC efficiency was obtained at Ti 150 nm.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.1
• /
• pp.126-133
• /
• 2017

This paper deals with the effects of welding, which is done to fix the stator stack, on a motor in case of fabricating a prototype motor that is manufactured in a small quantity. In the case of a small motor, the stator is designed and fabricated with the segmented core as a way to raise the fill factor of winding wire to the utmost within a limited size. In case of fabrication by welding both inside and outside of the stator in order to fix the segmented-core stator, the effects of stack are ignored, and the eddy current loss occurs. This paper performed the no-load test on an IPM-type BLDC motor for driving the suction fan of a vacuum cleaner, which was manufactured by using a segmented-core stator. As a result of the test, it was found that input power more than expected was supplied. To analyze the effects of welding by using the finite element analysis method and verify them experimentally, a stator was re-manufactured by bonding, and input power supplied during the no-load test was compared.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.11
• /
• pp.731-736
• /
• 2015

Rhodamine B (RhB) was utilized as a dye sensitizer for dye-sensitized solar cells (DSSCs) and its photovoltaic property was examined under the illumination of AM 1.5 G, $100mWcm^{-2}$. DSSCs based on RhB exhibited typical photovoltaic properties with an open-circuit voltage ($V_{OC}$) of 0.34 V, a short-circuit current ($J_{SC}$) of $1.55mA{\cdot}cm^{-2}$, a fill factor (FF) of 50%, and a conversion efficiency (PCE) of 0.26%. In order to further improve the photovoltaic properties of RhB-based DSSCs, the effect of (i) incorporating a strong electron-donating NCS unit into the RhB molecular backbone, (ii) combining a bis-negatively charged zinc complex anion ($Zn-dmit_2$, dmit=di-mercapto-dithiol-thione) with the amine cation of RhB, (iii) co-adsorbing RhB dyes with chenodeoxycholic acid (CDCA) molecules onto porous $TiO_2$ electrodes, was investigated and discussed.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.225-226
• /
• 2016

통상적으로, 기존 단상 AC 전원용 플라이백 컨버터는 75W 이상의 조건에서 역률개선회로를 채용하게 된다. 이에 따라 2-Stage 형태의 회로를 구성해야 하기 때문에, 회로의 부품 수 증가 및 전력 효율을 낮추는 단점이 동반된다. 또한, 다수의 자성소자(인덕터, 트랜스포머) 사용이 필수적이며, 이는 회로의 부피 및 원가 상승의 주요한 원인이 된다. 본 논문에서는 역률 개선 기능을 가진 밸리필 플라이백 컨버터의 실용적 설계 및 구현 방안을 제시한다. 더불어, 밸리필 정류기의 전해 커패시터 Short 시 방폭 문제를 해결하기 위한 OVP(Over Voltage Protection) 회로의 실용적 설계 방법을 제시하여 제안 회로의 양산 가능성을 증명한다. 본 논문에서는 제안 회로의 이론적 특성을 분석하고, 78W 급 플라이백 컨버터 시작품의 실험적 분석을 통해 그 타당성을 검증한다.

• Journal of Powder Materials
• /
• v.16 no.5
• /
• pp.305-309
• /
• 2009

The effect of light scattering layers (400 nm, TiO$_2$ particle) of 4 $\mu$m thickness on the dye-sensitized solar cell has been investigated with a 12 $\mu$m thickness of photo-anode (20 nm, TiO$_2$ particle). Two different structures of scattering layers (separated and back) were applied to investigate the light transmitting behaviors and solar cell properties. The light transmittance and cell efficiency significantly improved with inserting scattering layers. The back scattering layer structure had more effective transmitting behavior, but separated scattering layer (center: 2 $\mu$m, back: 2 $\mu$m) structure (9.83% of efficiency) showing higher efficiency (0.6%), short circuit current density (0.26 mA/cm$^2$) and fill factor (0.02). The inserting separating two scattering layers improved the light harvesting, and relatively thin back scattering layer (2 $\mu$m of thickness) minimized interruption of ion diffusion in liquid electrolyte.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05d
• /
• pp.65-68
• /
• 2003

Recently, there is a growing concern on the photovoltaic effects using organic materials. This is a phenomena which converts the solar energy into the electrical one. We have fabricated a device structure of ITO/PEDOT:PSS/CuPc/$C_{60}$/BCP/Al. The PEDOT:PSS layer is made by spin coating. and the other organic layers are made by thermal vapor deposition. By measuring the current-voltage characteristics with an illumination of light. we have obtained a value of $V_{oc}$=0.358V and $J_{sc}$=0.338mA/$cm^2$. A fill factor and efficiency are about 0.271 and 0.033%, respectively. A 500W xenon lamp(ORIEL) was used for a light source, and the light intensity illuminated into the device was about 10mW.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.6
• /
• pp.2058-2062
• /
• 2011

The effect of the addition of ionic liquids with four different cations (imidazolium, pyrrolidinium, piperidinium and pyridinium) on the performance of dye-sensitized $TiO_2$ solar cells based on electrolytes containing a t-butylpyridine (TBP) in 3-methoxypropionitrile (MPN) was studied. A total of 18 ionic liquids with mono-, di- and tri-alkyl derivatives were used in the present study, and among them a pyridinium cation with a mono-alkyl group showed better cell efficiency than the others. The best photoelectric conversion efficiency, 7.213%, was obtained using 1-hexylpyridinium iodide with an open-circuit photovoltage ($V_{oc}$) = 0.731 V, a short-circuit photocurrent density ($J_{sc}$) = 16.175 $mA/cm^2$, and a fill factor (ff) = 0.610 under AM1.5 and 100 $mW/cm^2$ illumination.