• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.2
• /
• pp.117-123
• /
• 2013

As fiber reinforced polymer (FRP) material is appled for a curved structure such as tunnel, FRP material must has a curved shape. Until now, the curved FRP material has been producted by hand-lay-up or filament winding work. It is impossible for mass production of the curved FRP material by these methods. Also, the quality of product by these methods is lower than that by pultrusion method. New pultrusion method and equipment had been developed for production of FRP material with steady curvature. The objective of this study is to evaluate the effect of freezing and thawing on adhesion of cement concrete with coarse-sand coated FRP in repair and reinforcement of cement-concrete structure using curved FRP material.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.6 no.1
• /
• pp.17-26
• /
• 1982

This article aims to determine the interrelation among exfoliation strength, the repeated laundry number, the coefficient of friction and the cover factor about the fusible interlining produced by using different amount resin. The practicality of stiffness and warmth of the fusible interling were examined. The results are summarized as follows: 1) As a factor that affecting the exfoliation strength of fusible interlining, the coefficient of friction and the cover factor about the fusible interlining produced by using different amount resin. (2) Regardless of the weight of the resin, the exfoliation strength of fusible interlining declined gradually as the repeated laundry number increased. This tendency arises much more in the case of the filament yarn fabric than in that of the spun yarn fabric. The stability of the exfoliation strength was better, regardless of the increase of the repeated laundry number, when the weight of the weight of the resin was 10 g/$m^2$. (3) The spun yarn fabric, which has more fuzz than the filament yarn fabric, is more suitable for the fabric of fusible interlining. The smaller the cover factor difference between the face cloth and the interlining cloth, the stronger the exfoliation strength. (4) When the stability of the shape is a necessary factor in the consumption of the fusible interlining, a resin weight of 20 g/$m^2$ is the most suitable; however when stiffness and warmth are necessary factors, a resin weight of 10 g/$m^2$ is the most suitable.

• Journal of radiological science and technology
• /
• v.41 no.1
• /
• pp.61-66
• /
• 2018

The recent 3D printing technology is used in various medical, manufacturing, and education fields and is more efficient in terms of production process, time, and cost than existing production. Especially in fracture surgery, interest and research have been focused on improving accuracy, shortening of operation time and recovery time, and reducing reoperation. However, because of the financial and technical problems of the 3D printer and the file conversion program, the 3D printing is made directly at the hospital, and it is not generally used for diagnosis of fracture and surgical research. In this study, to solve those problems, clavicle CT imaging was switched into Osirix Open Source DICOM Viewer, Stereolithography file conversion programs and commercial Terarecon 3D DICOM Viewer, file conversion programs, and then clavicle fracture model was directly made through 3D printer of fused filament fabrication wire additive processing method, and then the accuracy of the shape was compared and analyzed. Clavicle fracture models printed in two methods were blind-tested on clinicians of general hospitals' orthopedics and radiologic technicians with over 10 years of experiences, and then their analysis opinions of resolution reviews were analyzed. The result showed no difference. The 3D printing model with open source DICOM STL file conversion program used was applicable to clinical, so it is considered useful in precision diagnosis of fracture and operation plans.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.5
• /
• pp.333-339
• /
• 2016

In this paper, a fundamental experiment regarding the formation of porous 3D structures for personal safety products using 3D PPP (Porous Polymer Printing) was introduced for the first time. The filament was manufactured by mixing PP (Polypropylene) and CBA (Chemical Blowing Agent) with polymer extruder, and the diameter of the filament was approximately 1.75mm. The proposed 3D PPP method, combined with the conventional FDM (Fused Deposition Modeling) procedure, was influenced by process parameters, such as the nozzle temperature, printing speed and CBA density. In order to verify the best processing conditions, the depositing parameters were experimentally investigated for the porous polymer structure. These results provide parameters under which to form a multiple of 3D porous polymer structures, as well as various other 3D structures, and help to improve the mechanical shock absorption for personal safety products.

• Composites Research
• /
• v.21 no.3
• /
• pp.9-17
• /
• 2008

In this paper, the low velocity impact characteristics of filament winding CFRP pressure vessel was investigated using numerical and experimental methods. The cylinder part of CFRP vessel was impacted using triangular shape impactor which simulated the sharp edge of dropping tools and impact response behavior of CFRP was reviewed. The mechanical behavior, such as deformation and stress distribution, were also predicted by explicit finite element method and the validity of the model was investigated. For the quantitative evaluation of the residual strength of the pressure vessel after impact, a series of the ring specimens was cut from the impacted vessel and its burst pressure was measured by hydraulic pressure hoop tension test. As the results, the relationship between the residual strength degradation and the impact energy was successively obtained and a useful methodology to evaluate quantitatively the impact damage tolerance of CFRP pressure vessel was established.

• BMB Reports
• /
• v.51 no.7
• /
• pp.327-337
• /
• 2018

Lamin A and its alternative splicing product Lamin C are the key intermediate filaments (IFs) of the inner nuclear membrane intermediate filament. Lamin A/C forms the inner nuclear mesh with Lamin B and works as a frame with a nuclear shape. In addition to supporting the function of nucleus, nuclear lamins perform important roles such as holding the nuclear pore complex and chromatin. However, mutations on the Lamin A or Lamin B related proteins induce various types of human genetic disorders and diseases including premature aging syndromes, muscular dystrophy, lipodystrophy and neuropathy. In this review, we briefly overview the relevance of genetic mutations of Lamin A, human disorders and laminopathies. We also discuss a mouse model for genetic diseases. Finally, we describe the current treatment for laminopathies.

• ALGAE
• /
• v.30 no.3
• /
• pp.207-216
• /
• 2015

Caloglossa species occurs in freshwater streams around Southest Asia. We report it from 2 different riverine sites in Kerala, India. Tetrasporangiate plants were observed in field collections from the Periyar River and Chalakkudy River. The Chalakkudy isolate did not reproduce in culture but the Periyar isolate developed abundant tetrasporangial sori in culture. Many spores were discharged and most were abortive, but some germinated normally, sporelings forming male gametophytes with numerous spermatangial sori and females with many procarps, viable carposporophytes and some nonfunctional (no carpospores) pseudocystocarps. Some carpospores germinated forming new tetrasporophytes. Molecular evidence (28S rDNA and rbcL) placed the Indian specimens close to C. beccarii and C. fluviatilis. Considering the freshwater habitat and morphology of vegetative thalli (blade shape, rhizoid arrangement, and number of rhizoid filament per cell), the Indian specimens should be assigned to C. beccarii.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.50 no.8
• /
• pp.367-373
• /
• 2001

This paper presents racetrack High Temperature Superconducting (HTS) magnet with iron plates to achieve the maximum current-carrying capacity and the simple shape that can easily be wound and jointed. On the basis of the magnetic field analysis using Biot-Savart's law and 3 Dimensional Finite Element Analysis (3D FEA), this study is focused on the function of iron plates, which is to obtain smaller B${\perp}$, and stress and strain condition of Ag-sheathed Bi-2223 37-filament HTS tapes are considered. Moreover, the measured performance of the magnet with iron plates improved by 50% on the basis of initial magnet.

• Applied Microscopy
• /
• v.17 no.1
• /
• pp.1-15
• /
• 1987

Testes from the allied rock wallaby(Petrogale assimilus) have been examined by the electron microscopy in thin sections in order to examine spermiogenesis and structure of spermatozoa. The spermiogenesis can be divided into nine stages: early Golgi, late Golgi, collapsing, nuclear protrusion, condensation and flattening, nuclear shaping, rotation, nuclear ring contraction, and maturation. The acrosome has been abruptly formed following the collapse of expanded acrosomal vesicle without the cap stage described in the eutheria. The flatly condensed nucleus rotates obliquely to the axis of the axial filament complex and the folded acrosome covers the anterior third of the dorsal nuclear surface forming a wide subacrosormal space as the nuclear ring has contracted. The Sertoli cell reaction and spur are prominent during the nuclear protrusion and rotation stages. A mature spermatozoon has S-shape head which has an extended part reaching to the vicinity of the middle piece.

• Animal Systematics, Evolution and Diversity
• /
• v.14 no.4
• /
• pp.335-340
• /
• 1998

Two new species of the family Irciniidae, Psammocinia wandoensis n.sp. and P.samyangensis n. sp., are described. They were collected from the South Sea, Korea. P. wandoensis n. sp. closely resembles P. rugosa(Lendenfed, 1889)from Australia in morphology, but new species differs from P. rugosa by the filaments. Though P. samyangensis n. sp. is very similar to P. jejuensis, but our species differs from P. Jejuensis by the fibre shape.