• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.772-776
• /
• 2001

The flow structures of turbulent shear layer behind oil fences with different tip configurations were investigated experimentally using flow visualization and PIV velocity field measurement. An oil fence was installed in a circulating water channel and the flow structure around the fence tip was mainly analyzed in this experiment. The four tip configurations tested in this experiment are knife edge; semi-circle edge, circular edge and rectangular edge. The 300 instantaneous velocity fields were measured using the single-frame PIV system and they were ensemble averaged to give the mean velocity field and spatial distribution of turbulent statistics. Free stream velocity was fixed at 10ms/sec and the corresponding Reynolds number based on the fence height was Re=4000. As a result, for the oil fence with rectangular edge, the streamwise velocity component was decreased. On the other hand it was increased for the oil fence with circular edge. For all four fences tested in this study, general flow pattern of the lower shear layer is analogous but the upper layer shows difference depending on the tip configurations. The oil fence with circular edge has more diffusive upper shear layer than that of the others. The shear layer of the oil fence with rectangular edge has relatively thin thickness. The oil fence with circular edge was found to be proper shape for tandem fence.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.8
• /
• pp.1111-1120
• /
• 1998

Spray Drying Absorber(SDA) system, where the combustion product gas is mixed with atomized limestone-slurry droplets and then the chemical reaction of $SO_2$ with alkaline components of the liquid droplets forms sulfates, has been widely used to eliminate $SO_2$ gas from coal fired power plants and waste incinerators. Liquid atomization is necessary because it can maximize the reaction efficiency by increasing the total surface area and dispersion angle of the alkaline components. First, numerical calculations using FLUENT are carried out to investigate $SO_2$ concentration distribution and thus to calculate $SO_2$ removal efficiency. So to attain the optimized spray conditions, then an electrostatic spraying system is set up and spray visualization is performed to show the effect of an electric field on overall droplet size. Next, the effect of an electric field on the concentrations of $SO_2$ is experimentally examined. Field strength is varied from -10 kV to 10 kV and configurations of conduction charging and induction charging are utilized. Consequently, the electrostatic removal efficiency of 501 increases about 30% with the applied voltage of ${\pm}10kV$ but is independent of polarity of the applied voltage. It Is also found that the conduction charging configuration results in higher efficiency of $SO_2$ removal that the induction charging configuration. Finally, the effect of slurry temperature on $SO_2$ removal is studied. The temperature influences on the electrostatic removal efficiency of $SO_2$.

• Journal of the Korean housing association
• /
• v.25 no.4
• /
• pp.83-91
• /
• 2014

The purpose of this study is to clarify the characteristics between the type of daily routine and spatial configuration of activity areas in classroom and provide alternatives for space planning of activity areas in classroom of child-care centers. This study used the content analysis on daily activity plan and floor plans through field survey. Analysis on floor plans was conducted for 35 classrooms in 9 child-care centers which allowed field survey. The results of this study were as follows; There was no significant difference for classroom size according to the type of daily routine in 3 to 5-year-old classrooms. The average size of classrooms was $61.6m^2$ for care oriented type, $41.4m^2$ for indoor activity oriented type and $48.8m^2$ for group activity oriented type. There was no significant difference in composition of activity areas in classrooms according to the type of daily routine. In case of 0 to 2-year-old classrooms, they were composed of 6 activity areas including gross-motor, role play, block building, language, creative expression, exploration/manipulation. Activity area of the most low frequency was gross-motor area. In case of 3 to 5-year-old classrooms, most classrooms were composed of all the 7 activity areas including art, tone and rhythmic, block building, role play, language, math and science. Most accessible and central areas in 0 to 2-year-old classrooms were gross-motor and role play. Also, most separate areas were exploration/manipulation and block building. Most accessible and central areas in 3 to 5-year-old classroom were art and math. Also, most separate areas were tone and rhythmic and science.

• Journal of Korea Society of Industrial Information Systems
• /
• v.25 no.5
• /
• pp.49-57
• /
• 2020

Conventional electric motors are not suitable for aircraft because of their large size and weight. High-temperature superconducting (HTS) motors have high current density, high magnetic field density, and low loss, so they can significantly reduce the size and weight compared to general electric motors. This paper presents the conceptual design and analysis results of HTS motors for electric propulsion in future aircraft. A 2.5 MW HTS motor with a rotational speed of 7,200 RPM was designed and the specific power (kW/kg) was analyzed. The operating temperature of the field coil of the HTS motor is 20K in consideration of LH2 cooling. The stator winding were connected in a multi-phase configuration and Litz wires were used to minimize eddy current losses. As a result, it was confirmed that the specific power of the motor is about 18.67 kW/kg, which is much higher than that of the conventional electric motor.

• Journal of Advanced Navigation Technology
• /
• v.25 no.6
• /
• pp.530-535
• /
• 2021

In this paper, the design method for a chipless RFID tag using ELC resonators is proposed. A four-bit chipless RFID tag is designed in a two by two array configuration using three ELC resonators with different resonant peak frequencies and one compact IDC resonator. The resonant peak frequency of the bistatic RCS for the IDC resonator is 3.125 GHz, whereas those of the three ELC resonators are adjusted to be at 4.225 GHz, 4.825 GHz, and 5.240 GHz, respectively, by using the gap between the capacitor-shaped strips in the ELC resonator. The spacing between the resonators is 1 mm. Proposed four-bit tag is fabricated on an RF-301 substrate with dimensions of 50 mm×20 mm and a thickness of 0.8 mm. It is observed from experiment results that the resonant peak frequencies of the fabricated four-bit chipless RFID tag are 3.290 GHz, 4.295 GHz, 4.835 GHz, and 5.230 GHz, respectively, which is similar to the simulation results with errors in the range between -2.3% and 0.2%.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.1 no.4
• /
• pp.505-508
• /
• 2012

A permanent magnet flux switching (PMFS) machine has a simple rotor, whilst both magnets and coils are set in the stator, resulting in easy removal of heat due to both copper loss and eddy current loss in magnets. However, the volume of magnets used in PMFS machines is usually larger than in conventional PM machines, and leakage flux does exist at the non-airgap side. To make full use of the magnets and gain higher power density, a novel 3-dimensional (3D) field PMFS machine is developed. It combines merits of the tubular linear machine, external-rotor rotary machine and axial-flux rotary machine, hence, offers high power density and peak torque capability, as well as efficient utility of magnets owing to the unique configuration of triple airgap fields.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1197-1199
• /
• 2004

We have studied an optically compensated splay (OCS) mode driven by fringe electric field. The OCS configuration obtained by applying voltage to vertically aligned LCs shows a dark state when an optic axis of the OCS cell coincides with one of crossed polarizer axis. When the fringe electric field is applied, the LC director rotates in plane above whole electrode surface, giving rise to the high transmittance, the low operating voltage and wide viewing angle simultaneously.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.8
• /
• pp.2005-2015
• /
• 1994

An analytical method based on the upper bound approach for the cup-bar axisymmetric combined extrusion is presented to determine the deformation zones as well as extrusion load and deformed geometry in the early stage. A new kiematically admissible velocity field is derived by the appropriate transformation of the original velocity field and applying the flow function approach. The derived velocity field is directly related to the boundary function for the plastically deforming zones and the parameter controlling the flow direction to the forward part or backward part. Experiments are carred out with the annealed aluminum 2024 at room temperature for the various area reductions. The workhardening effect is considered in the formulation as a function of the height ratio between the deformed billet and the orighinal billet to calculate the extrusion pressures. The theoretical predictions for the extrusion loads and deformed configuration are in good agreement with the experimental results.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.336-339
• /
• 2007

A sensor having capability to measure two different kinds of ultrasonic waves selectively is described. Under the same bias field configuration, this magnetostrictive type sensor can selectively measure longitudinal waves and flexural ones. Since the switching operation of mode selection is made only by changing the polarity of the permanent magnets used to configure the bias field, it will be very useful after the permanent magnet are interchanged with electromagnets. In order to find the optimal operating bias field, finite elements analysis is used and the condition for flexural wave measurements to meet is found. The linearity of the sensor is verified by experiments and the requirements for linearity also are proposed.

• 한국전산유체공학회:학술대회논문집
• /
• 2005.10a
• /
• pp.27-30
• /
• 2005

In a microfluidic chips pressure driven flow or electro-osmotic flow has been usually employed to deliver bio-samples. Flow in the chips is usually slow and the mixing performance is poor. A micro-mixer with a rapid mixing is important for practical applications. In this study a newly designed and electro-osmotic driven micro-mixer is proposed. This design is comprised of a channel and a series of metal electrodes periodically attached on the side surface. In this configuration electro-osmotic flows and the stirring effects are simulated three-dimensionally using a commercial code, CFD-ACE. Focus is given the effect on the electro-osmotic flow characteristics under the local variation of the electric field.