• Journal of Korean Society of Transportation
• /
• v.27 no.5
• /
• pp.179-187
• /
• 2009

This study develops a real-time signal control algorithm based on sectional travel times and includes a field test and evaluation. The objective function of the signal control algorithm is the equalization of delay of traffic movements, and the main process is calculating dissolved time of the queue and delay using the sectional travel time and detection time of individual vehicles. Then this algorithm calculates the delay variation and a targeted red time and calculates the length of the cycle and phase. A progression factor from the US HCM was applied as a method to consider the effect of coordinating the delay calculation, and this algorithm uses the average delay and detection time of probe vehicles, which were collected during the accumulated cycle for a stabile signal control. As a result of the field test and evaluation through the application of the traffic signal control algorithm on four consecutive intersections at 400m intervals, reduction of delay and an equalization effect of delay against TOD control were confirmed using the standard deviation of delay by traffic movements. This study was conducted to develop a real-time traffic signal control algorithm based on sectional travel time, using general-purpose traffic information detectors. With the current practice of disseminating ubiquitous technology, the aim of this study was a fundamental change of the traffic signal control method.

• Geomechanics and Engineering
• /
• v.24 no.2
• /
• pp.115-127
• /
• 2021

This paper investigates the effects of soaking on a lime stabilized high plasticity clay and evaluates the implications for pavement design. In this context, the soil was stabilized by 4%, 6% and 9% hydrated lime. The soil was pulverized in two different gradations so that representative field gradations could be simulated. Both soil pulverization levels passed the relevant field gradation criteria. Curing durations were chosen as 7 days, 28 days and 56 days. Two groups of samples were prepared and were tested in unconfined compression test apparatus to measure the strength and secant modulus at failure values. One of the groups was tested immediately after curing. The other group of samples were first cured and then subjected to soaking for ten days before testing. Visual observations were made on the samples during the soaking period. The results showed the superiority of fine soil pulverization over coarse soil pulverization for unsoaked conditions in terms of strength and modulus values. Soaking of the samples affected the unconfined compressive strength and modulus values based on lime content, curing duration and soil pulverization level. In soaked samples, fine soil pulverization resulted in higher strength and modulus values compared to coarse soil pulverization. However, even with fine soil pulverization, effects of soaking on modulus values were more significant. A new term named as "Soaking Influence Factor (SIF)" was defined to compare the reduction in strength and modulus due to soaking. The data was compared with the relevant design guidelines and an attempt was made to include Soaking Influence Factors for strength and modulus (SIFS and SIFM) into pavement design processes. Two equations which correlated secant modulus at failure to unconfined compressive strength were proposed based on the samples subjected to soaking. The results of this study showed that in order to decrease the diverse effects of soaking for lime stabilized soils, soil pulverization level should be kept as fine as possible in the field. Importance of proper drainage precautions in the pavements is highlighted for better performance of the pavements.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.57 no.4
• /
• pp.11-19
• /
• 2015

The important properties of EVA (ethylene vinyl acetate) redispersible polymer was waterproof, densification of internal pore space of concrete and ball bearing and micro filler. Also, the significant role of polypropylene(PP) fiber was crack control and blockade of movement for deterioration factors. The most studies for EVA were limited in the field of mortar and PP fiber reinforced concrete had been studied in the state of being restricted unit water content, rich mix and mixing much of the fiber without considering construction site. Therefore, the control mix design were applied in ready mixed concrete using 10 % fly ash of total cement weight used in batch plant. On the basis of control mix design, EVA contents ranging from 0 % to 10 % of total cement weight and PP fiber contents ranging from 0 % to 0.5 % of EVA concrete volume were used in the mix designs. The results showed the maximum compressive strength value was measured at EVA 5.0 % and PP fiber 0.1 %, the minimum water absorption ratio was at EVA 10 % and PP fiber 0 %, the durability factor for freezing and thawing resistance was at EVA 5.0 % and PP fiber 0.3 % and the minimum weight reduction ratio of resistance to sulfuric acid attack was at EVA 10 % and PP fiber 0.5 % after curing age 42days. Meanwhile, From these results, PP fiber reinforced EVA concrete would be very benefit, if each optimal mix types were used in hydraulic structures, underground utilities and agricultural structures.

• Journal of Labour Economics
• /
• v.41 no.1
• /
• pp.83-124
• /
• 2018

In this study, with the data of Human Capital Corporate Panel(HCCP) we find that the explaining power of the new hiring rate of experienced regular workers is very strong and statistically significant as a main causal factor to the decreasing trend of investment on education and training for workers in corporates, which means a sign of weakening of the internal labor market. Possibility of wage penalty from switching jobs has been weakened considerably too. The effective alternative policy measures to the weakening or laxity of the internal labor markets and whereby followed reduction in investment on education and training for workers in corporates are construction of social system outside of individual corporates to upbring field-tailored manpower of high quality for young generations and small and medium sized enterprises.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.04a
• /
• pp.146-149
• /
• 2005

The using of composite material is an aviation field but it changes into a general industry. Especially composites are expanding the use on transportation vehicles like automobiles, ships, and aircrafts. The main factor of this expansion is high specific strength. It can supply a high quality and efficiency of energy. But manufacturing of composite products requires many raw materials and tooling cost for special process, so we needs a reduction of these costs to achieve best efficiency. In the present study, we contrast the change of mechanical and physical properties between VaRTM(Vacuum Assisted Resin Transfer Molding) and hand lay-up process. VaRTM process can offer a high quality the same as autoclave products, and low cost like hand lay-up process. In the results of mechanical tests, VaRTM specimen is stronger than hand lay-up specimen and hand lay-up specimen became delamination. In the results of physical tests, the resin content of VaRTM specimen is lower than hand lay-up specimen. On micrograph, the strength of specimen by VaRTM between fiber and resin is stronger than that of one by hand lay-up. And the specimen by hand lay-up contains more defects than one by VaRTM. So, VaRTM process can practically apply for automobile engine hood. This paper shows that VaRTM process is one of the most suitable processes for composite parts of automobile.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.148-152
• /
• 2007

In recent days, on account of the cultural development and the improvement of citizen's consciousness level, it is the real situation that the construction of small-scaled Multi-Purpose Hall where various cultural events could be performed, is on increasing. However, since the most of Multi-Purpose Hall had been designed and built up without any consideration on Acoustic Factor, many problems are on occurring thereat. Since those small-scaled Multi-Purpose Hall have been mostly used with the finishing material which contains a high degree of Acoustic Absorption indiscreetly, both diffusion and reflection of sound are not establishing properly, and because thereverberation of sound is very low, in case of musical performance by musical instrument, its sound hears too arid and stiff, there occurs some acoustic defect such as it becomes difficult for music appreciation with sufficient timbre, so that the capability improvement on the matter is urgently requiring situation. Therefore, this Study has tried to seize the satisfaction level about the small-scaled Multi-Purpose Hall after betterment of the acoustic performance by appraise the acoustic condition of the Hall, using Auralization Technique that can experience Virtual Acoustic Field regarding to the small-scaled Multi-Purpose Hall as its object. It is deemed that such research result could be practically used as the useful material which enables to bring a reduction effect of construction cost as well asenhancement of the acoustic performance through its presupposition?control on the acoustic problem when construction or renovation of other similar small-scaled Multi-Purpose Hall in the future.

• Journal of Korean Society of Water and Wastewater
• /
• v.34 no.2
• /
• pp.149-159
• /
• 2020

Cured-in-place-pipe(CIPP) is the most adopted trenchless application for sewer rehabilitation to extend the life of the existing sewer without compromising both direct construction and indirect social costs especially applied in the congested urban area. This technology is globally and domestically known to be the most suitable for partial and full deteriorated pipe structure rehabilitation in a sewer system. The typical design of CIPP requires a significant thickness of lining to support loading causing sewage flow interruption and increasing material cost. This paper presents development of a high strength glass fiber composite lining material for the CIPP application and structural test results. The test results exhibit that the new glass fiber composite lining material has 12 times of flexural strength, 6.2 times of flexural modulus, and 0.5 Creep Retention Factor. These test results can reduce lining design thickness 35% at minimum. Even though taking into consideration extra materials such as outer and inner films for actual field applications, the structural capacity of the composite material significantly increases and it reduces 20 percent or more line thickness as compared to the conventional CIPP. We expect that the newly developed CIPP lining material lowers material costs and minimizes flow capacity reduction, and fully replaceable to the conventional CIPP lining materials.

• Design & Manufacturing
• /
• v.11 no.1
• /
• pp.39-44
• /
• 2017

The domestic mold industry is composed of 6,560 small and medium sized mold companies as of 2015. The structure of mold industry centered on less than 10 people in the past has been improved in the direction of increasing number of medium and large scale companies with more than 20 competitors with global competitiveness and has maintained its position as the world's second largest mold exporter with global competitiveness. Nevertheless, the manpower structure and corporate competitiveness structure of the mold industry is very high, with the proportion of production manpower reaching 70% and shortage rate of 10% or more in order to respond to the orders of customers. However, the development base for new employees with technological skills required by the industrial field is poor, and the inflow of young people is very limited due to factors such as the avoidance of small and medium enterprises and production jobs. It is expected that the labor shortage of mold enterprises will be further increased in the future. In the mold industry, due to the characteristics of small quantity multi-product production corresponding to the demand of the consumer, many production processes are individually and independently carried out, resulting in low labor productivity, and the structural time required for the worker to increase the working time Due to limitations, the working hours per week of the employees are about 50 hours. The implementation of the working time reduction bill, which is recently promoted by the government, is a crisis factor. In order to cultivate the mold industry, it is necessary to expand the base of molds to meet the intensification of global competition, the convergence of technologies to actively respond to the restructuring of the industrial structure, and the response to the new industry, It is necessary to improve labor productivity through policies such as development and dissemination of system, and to secure price, delivery and quality competitiveness in global market.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.23 no.2
• /
• pp.17-31
• /
• 2020

In the field of environmental landscape architecture, the internet medium is used as an effective communication tool not only in the private level but also in the policy level. Recently, the active utilization of mobile web service is emphasized as the time changes, but there is not much improvement or advance in services due to lack of relevant studies. Therefore, this study is intended to provide basic data needed for improvement and advance by researching the quality of mobile web service among multichannel services provided in environmental landscape architecture related internet media. The model for measuring service quality is SERVQUAL, which was verified in the study of Choi(2015), Choi and Koo(2016), and the final valid samples are total 230. First, the subjects were analyzed as the representative media that are possible to acquire comprehensive knowledge related to environmental landscape architecture. Second, the highest importance level in each subsection was 'protection and security maintenance of customer information' followed by 'Reliability about accurate information supply'. Regarding performance level, 'Reliability about accurate information supply' and 'professional knowledge to communicate with users' are highly evaluated. Third, regarding Importance-Performance Analysis(IPA), the first priority management should is 'Tangibles', and the next are 'Responsibility' and 'Empathy'. The ones for maintenance of the status quo are 'Reliability' and 'Assurance', and there is none for effort reduction. Meanwhile, regarding the importance of each factor and difference in the quality of PC web service and mobile web service studied before, the biggest difference is in 'Tangibles', followed by 'Assurance', 'Empathy', 'Responsibility' and 'Reliability'. It is suggested that the revitalization of Landscape information science(LB1106) presented in the National Science&Technology Standard Classification System is needed. In the future, it is necessary to research the change trend on users' response through continuous evaluation of improved mobile web service.

• Journal of Korean Society for Atmospheric Environment
• /
• v.16 no.1
• /
• pp.49-60
• /
• 2000

The concentration of atmospheric mercury(Hg0 and relevent environmental parameters that include both meteorological and criteria pollutant data were dtermined at hourly intervals during two field campaigns covering the periods of September 1997 and May/June 1998. The mean concentrations of Hg for the two study periods were computed as 3.94 and 3.43ngm-3, respectively. Through a separation of these data into both daytime and nighttime periods, we further analyzed diurnal variation patterns for Hg between two different seasons. Using our Hg data sets, we were able to recognize two contrasting diurnal variation patterns of Hg between two diffeerent seasons that can be characterized as: (1) the occurrences of peak Hg concentration during daytime(fall0 and (2) slight reductions in daytime Hg concentration relative to nighttiime Hg data(summer). To study the systematic differences in diurnal patterns between two different seasons, we analyzed Hg data in terms of different statistical approaches such as correlation(and linear regression0 and factor analysis. Results of these analyses consistently indicated that different mechanisms were responsible for controlling the daytime distribution patterns of Hg. The variation of boundary layer conditions betwen day/night periods may have been important in introducing the relative reduction in daytime Hg levels during summer. However, when the relationship between Hg and concurrently determined O3 is concerned, these differences are unlikely to be an effective sink mechanism within the ranges of ozone concentrations determined concurrently during this study, regardless of season. To further provide the general account for short-term variations in Hg distribution data, we should be able to describe the various factors underlying its sink mechanism.