• 한국광학회:학술대회논문집
• /
• 한국광학회 1989년도 제4회 파동 및 레이저 학술발표회 4th Conference on Waves and lasers 논문집 - 한국광학회
• /
• pp.113-118
• /
• 1989

By using the single mode optical fiber, we fabricated Fiber-optic Fabry-Perot interferometer (FFPI). The change over a wide range in the optical path length of a FFPI is observed. The temporal movement of the interference fringes by external condition to P.Z. T) is converted to circular motion on an oscilloscope display and then recorded with a micro-computer. The two output voltages of the D/A converters are applied to X and Y terminals of oscilloscope to display circular motion on oscilloscope. Thus the direction of phase shift can be determined with observing the direction of circular motion. The variation of the optical length can be measured by calculating the angle of spot of circle with an accuracy of λ/90 wave length due to variation of temperature in this system 2.7x10-4$^{\circ}C$.

• Restorative Dentistry and Endodontics
• /
• 제46권4호
• /
• pp.50.1-50.8
• /
• 2021

Although several techniques have been proposed to remove fiber-reinforced composite (FRC) post, no safe and efficient technique has been established. Recently, a guided endodontics technique has been introduced in cases of pulp canal obliteration. This study describes 2 cases of FRC post removal from maxillary anterior teeth using this guided endodontics technique with a dental operating microscope. Optically scanned data set from plaster cast model was superimposed with the data set of cone-beam computed tomography. By implant planning software, the path of a guide drill was selected. Based on them, a customized stent was fabricated and utilized to remove the FRC post. Employing guided endodontics, the FRC post was removed quickly and safely with minimizing the loss of the remaining tooth structure. The guided endodontics was a useful option for FRC post removal.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 추계학술대회 논문집 학회본부
• /
• pp.552-554
• /
• 1995

In long-haul high speed optical communications, the distance between a transmitter and a receiver depends on the amount of light coupled to a single mode optical fiber from the laser diode(LD) as well as the LD characteristic itself. And the transmitter module must have long lifetime. high reliability, and even simple structure. Such points have induced laser welding technique to be a first choice in opto-electronic module packaging because it can provide strong weld joint in a short time with very small coupling loss. In this paper, packaging considerations and characteristics for high speed LD modules are discussed. They include optical path design factors for larger aligning tolerance, and novel laser welding processes for component assembly. For low coupling loss after laser welding processes, the optical path for optimum coupling of a single mode optical fiber into the LD chip was designed with the GRIN lens system providing sufficiently large aligning tolerance both in the radial and axial directions. The measured sensitivity of the LD module was better than -33.7dBm(back to back) at a BER of $10^{-10}$ with a 2.5Gbps NRZ $2^{23}-1$ PRBS.

• 천문학회보
• /
• 제40권1호
• /
• pp.53.2-53.2
• /
• 2015

Fiber Bragg gratings (FBGs) are the most compact and reliable method of suppressing atmospheric emission lines in the infrared for ground-based telescopes. It has been proved that real FBGs based filters were able to eliminate 63 bright sky lines with minimal interline losses in 2011 (GNOSIS). Inscribing FBGs on multi-core fibers offers advantages. Compared to arrays of individual SMFs, the multi-core fiber Bragg grating (MCFBG) is greatly reduced in size, resistant to damage, simple to fabricate, and easy to taper into a photonics lantern (PRAXIS). Multi-mode fibers should be used and the number of modes has to be large enough to capture a sufficient amount of light from the telescope. However, the fiber Bragg gratings can only be inscribed in the single-mode fiber. A photonic lantern bi-directionally converts multi-mode to single-mode. The number of cores in MCFBGs corresponds to the mode. For a writing system consisting of a single ultra-violet (UV) laser and phase mask, the standard writing method is insufficient to produce uniform MCFBGs due to the spatial variations of the field at each core within the fiber. Most significant technical challenges are consequences of the side-on illumination of the fiber. Firstly, the fiber cladding acts as a cylindrical lens, narrowing the incident beam as it passes through the air-cladding interface. Consequently, cores receive reduced or zero illumination, while the focusing induces variations in the power at those that are exposed. The second effect is the shadowing of the furthest cores by the cores nearest to the light source. Due to a higher refractive index of cores than the cladding, diffraction occurs at each core-cladding interface as well as cores absorb the light. As a result, any core that is located directly behind another in the beam path is underexposed or exposed to a distorted interference pattern from what phase mask originally generates. Technologies are discussed to overcome the problems and recent experimental results are presented as well as simulation results.

• 한국지반신소재학회논문집
• /
• 제2권1호
• /
• pp.47-55
• /
• 2003

14가지 니들펀치 부직포 지오텍스타일의 섬유구성인자인 두께, 기공도, 섬유장 및 직경 등이 수평투수성에 미치는 영향을 평가하였으며, 두께변화, 수평투수도, 압축 하중 하에서의 수평투수성을 구성방정식에 의해 분석, 평가하였다. 그리고 섬유 패킹 밀도가 다른 라미나(laminar) 지오텍스타일 복합재료를 제조하여 라미나 구조가 수직투수성에 미치는 영향을 평가하였다. 수평투수도는 부직포 지오텍스타일의 두께가 증가할수록 커졌으며, 기공도와 섬유직경이 커질수록 수평투수계수는 증가하였다. 수직응력이 증가할수록 기공도의 영향은 감소하였으며, 섬유장이 길수록 수평투수계수는 약간 크게 나타났다. 구성섬유의 직경이 클수록 수평 투수계수는 커지며, 직경의 비슷할수록 유사한 투수계수를 나타내었다. 라미나 지오텍스타일의 수직 투수성은 내부 경계면에서의 손실 수두에 영향을 받으며, 경계면에서 투수로의 연결형상은 bell mouth형이거나 부드러운 유입관 형태로 평가 되었다.

• 한국통신학회논문지
• /
• 제28권9B호
• /
• pp.793-805
• /
• 2003

헤더 정보와 버스트를 분리하여 전송되는 광 버스트 스위칭 망에서 장애의 발생은 심각한 서비스 품질 저하를 초래할 수 있으므로 신속한 복구 대책을 수립하여 망에서 발생하는 장애의 영향을 최소화하여야 한다. 본 논문에서는 먼저 기존에 제안된 복구 기법을 광 버스트 스위칭 망에 적용하여 각 링크의 장애에 따른 망 이용률 분석 및 버스트 손실률 등을 비교 평가하였다. 이에 대한 격과를 고려하여 망 구성 형태와 장애 링크의 위치를 고려한 ASPR (Area border router Sub-Path Restoration) 기법을 제안하였다. 제안된 기법은 장애 복구 지연 시간과 파장 변환기의 사용 효율성 관점에서 좋은 성능을 보이며 버스트 손실률, 망 자원 이용률, 그리고 버스트 처리율 관점에서 다른 기법과 비교 평가하였다.

• Computers and Concrete
• /
• 제19권1호
• /
• pp.59-68
• /
• 2017

This study focused on modeling the behavior of the compressive stress using the average strain and ultrasonic test results in concrete. Feed-forward backpropagation artificial neural network (ANN) models were used to compare four types of concrete mixtures with varying water cement ratio (WC), ordinary concrete (ORC) and concrete with short steel fiber-reinforcement (FRC). Sixteen (16) $150mm{\times}150mm{\times}150mm$ concrete cubes were used; each contained eighteen (18) data sets. Ultrasonic test with pitch-catch configuration was conducted at each loading state to record linear and nonlinear test response with multiple step loads. Statistical Spearman's rank correlation was used to reduce the input parameters. Different types of concrete produced similar top five input parameters that had high correlation to compressive stress: average strain (${\varepsilon}$), fundamental harmonic amplitude (A1), $2^{nd}$ harmonic amplitude (A2), $3^{rd}$ harmonic amplitude (A3), and peak to peak amplitude (PPA). Twenty-eight ANN models were trained, validated and tested. A model was chosen for each WC with the highest Pearson correlation coefficient (R) in testing, and the soundness of the behavior for the input parameters in relation to the compressive stress. The ANN model showed increasing WC produced delayed response to stress at initial stages, abruptly responding after 40%. This was due to the presence of more voids for high water cement ratio that activated Contact Acoustic Nonlinearity (CAN) at the latter stage of the loading path. FRC showed slow response to stress than ORC, indicating the resistance of short steel fiber that delayed stress increase against the loading path.

• 한국통신학회논문지
• /
• 제29권5A호
• /
• pp.473-483
• /
• 2004

8 채널 ${\times}$ 40 Gbps 파장 분할 다중 (WDM ： Wavelength Division Multiplexing) 시스템에서 색 분산과 자기 위상 변조에 의해 왜곡된 광 펄스를 최상으로 보상할 수 있는 광 위상 공액기 (OPC : Optical Phase Conjugator)의 최적 펌프 광 전력을 채널 입력 전력 변화에 따라 수치 해석적으로 살펴보았다. 또한 OPC의 펌프 전력 변화에 따른 수신단에서 허용 가능한 채널의 최대 입력 전력 크기를 변조 파형 형식, 광섬유 분산 계수에 따라 살펴보았다. 본 논문에서 고찰한 WDM 시스템은 전체 전송 링크 중간에 HNL-DSF (Highly- Nonlinear Dispersion Shifted fiber)를 비선형 매질로 이용한 OPC를 두어 보상하는 경로 평균 강도 근사 (PAIA ： Path-Averaged Intensity Approximation) MSSI (Mid-Span Spectral Inversion) 기법에 기초를 두고 있다. 우선 최소의 눈 열림 패널티를 만드는 HNL-DSF On의 특정 펌프 광 전력의 크기는 변조 파형 형식, 초기 채널 입력 전력, 총 전송 거리, 광섬유분산 등의 복합적인 영향에 따라 다소 변화될 수는 있지만 전력 변환비를 1 근처로 만드는 값에서 결정되어야 한다는 것을 알 수 있었다. 또한 HNL-DSP OPC의 펌프 광 전력이 최소의 EOP를 결과하는 최적의 값이 아닌 다른 값으로 설정되어 있는 경우 양호한 수신을 가능하게 하는 채널의 최대 입력 전력 크기는 광섬유의 분산 계수가 비교적 적은 WDM 시스템에서 변조 파형 형식으로 NRZ보다 RZ를 사통하면 더욱 증가되는 것을 확인할 수 있었다.

• 비파괴검사학회지
• /
• 제13권4호
• /
• pp.18-24
• /
• 1994

본 논문은 상호 상관관계 함수의 특성을 이용하여 이 함수 특성인 입력파와 출력파의 상관관계를 구하여 Lamb파의 $A_o$ mode의 속도를 알루미늄(6061-T651)에서 측정하여 본 결과 정확한 값을 구하였기에 일반적으로 속도 측정이 매우 힘든 망상형 유리섬유 복합체에 대한 음파의 전파속도를 측정하였다. 본 상호 상관 관계 함수의 특징은 외부의 어떠한 잡음에도 영향을 받지않고 쉽고 정확히 측정할 수 있으므로 그 응용면에 상당한 가치가 있고 또한 여러가지 입력파에 대한 입력파 원천 및 전파 경로 분석이 용이하여 본 복합체의 섬유구조 형태도 조사하여 본 결과 정량적 분석도 가능함을 알 수 있었다.

• Current Optics and Photonics
• /
• 제7권1호
• /
• pp.21-27
• /
• 2023

A highly sensitive optical-fiber humidity sensor is demonstrated in this paper. By using Nafion-PVA sol-gel and single-mode optical fibers, the Fabry-Perot humidity sensor is easily fabricated. In the humidity range of 29%-72%, humidity-response experiments are carried out with a cycle of rising and falling humidity to investigate humidity-response characteristics. The experimental results show 2.25 nm/%RH sensitivity and a 0.9997 linear correlation coefficient, with good consistency. The changes in optical-path difference (OPD) and free spectral range (FSR) with humidity are also discussed. The humidity sensitivities of a typical sensor are 80.3 nm/%RH (OPD) and 0.03 nm/%RH (FSR). Furthermore, many humidity sensors with different Nafion-PVA sol-gel concentration and initial cavity length are experimentally investigated for humidity response. The results show that the sensitivity increases with higher Nafion ratio of the Nafion-PVA sol-gel. The influence of changing cavity length on sensitivity is not obvious. These results are helpful to research on optical-fiber humidity sensors with good performance, easy fabrication, and low cost.