• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.1
• /
• pp.1-7
• /
• 2007

As fiber reinforced composite materials are widely used in aircraft, space structures and robot arms, the study on non-destructive testing methods has become an important research area for improving their reliability and safety. AE (acoustic emission) can evaluate the defects by detecting the emitting strain energy when elastic waves are generated by the initiation and growth of crack, plastic deformation, fiber breakage, matrix cleavage, or delamination. In the paper, AE signals generated under uniaxial tension were measured and analyzed using the $8{\times}8$ matrix piezo electric sensor. The electronic circuit to control the transmitting distance of AE signals was designed and constructed. The optical data storage system was also designed to store the AE signal of 64channels using LED (light emitting diode) elements. From the tests, it was shown that the source location and propagation path of AE signals in composite materials could be detected effectively by the $8{\times}8$ matrix piezo electric sensor.

• Korean Journal of Optics and Photonics
• /
• v.23 no.5
• /
• pp.217-221
• /
• 2012

In this paper, we have fabricated by means of the "Micro-Block Stacking (MBS)" method the 8 pin mini DIL integrated Triplexer, which can transmit CATV and voice/data at the same time in a single fiber. Our MBS technique is a novel scheme of compact optical module packaging which secures precision positioning of the components on the optical beam path by prefixed stacks of ceramic blocks. The subassembly in which a laser diode, two receiver photodiodes, two WDM filters, and four micro lenses are integrated is only $5.40mm{\times}2.15mm{\times}1.05mm$ in size. As the Triplexer is aligned to the single mode fiber, the transmitter power of -14.5 dBm and the receiver sensitivities of 0.83 A/W, 0.73 A/W for 1550 nm, 1490 nm, respectively are obtained.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.5
• /
• pp.869-886
• /
• 2018

Rockbolt is one of the most common supports used to reinforce discontinuous rock during underground excavation. Extra drain pipes are installed to improve excavation workability and the anchorage of rockbolts in water bearing ground. The drain pipe is effective in improving the workability by providing drainage path, but it is difficult to expect the reinforcement effect, increasing disturbance of the discontinuous rock mass and the construction cost. To solve this problem, dual purpose rockbolt (DPR) has been developed for the reinforcement of rock and the drainage of ground water. DPR was able to improve the mechanical and hydraulic stability of the rocks quickly and economically. Two kinds of DPRs using FRP (Fiber Reinforced Plastic) and steel were investigated for the mechanical and hydraulic performance. Also, the workability and stability of DPR were analyzed.

• Journal of Korean Institute of Industrial Engineers
• /
• v.30 no.3
• /
• pp.213-223
• /
• 2004

We consider the traffic grooming problem for the design of SONET/WDM(Synchronous Optical NETwork/Wavelength Division Multiplexing) ring networks. Given a physical network with ring topology and a set of traffic demands between pairs of nodes, we are to obtain a stack of rings with the objective of minimizing the number of ADMs installed at the nodes. This problem arises when a single ring capacity is not large enough to accommodate all the demands. As a solution method, an efficient algorithm based on the branch-and-price approach has been reported in the literature for the problem in which only unidirecional path switched ring (UPSR) was considered. In this study, we suggest integer programming models and the algorithms based on the same approach as the above one, considering two-fiber bidirectional line switched ring(BLSR/2), and BLSR/4 additionally. Using the results, we compare the number of required ADMs for all types of the ring architecture.

• Smart Structures and Systems
• /
• v.6 no.2
• /
• pp.91-100
• /
• 2010

An experimental study was carried out to investigate the shape control of plates via embedded shape memory alloy (SMA) wires. An extensive body of literature proposes the use of SMA wires to actively modify the shape or stiffness of a structure; in most cases, however, the study focuses on modeling and little experimental data is available. In this work, a simple proof of concept specimen was built by attaching four prestrained SMA wires to one side of a carbon fiber laminate plate strip. The specimen was clamped at one end and tested in an environmental chamber, measuring the tip displacement and the SMA temperature. At heating, actuation of the SMA wires bends the plate; at cooling deformation is partially recovered. The specimen was actuated a few times between two fixed temperatures $T_c$ and $T_h$, whereas in the last actuation a temperature $T_f$ > $T_h$ was reached. Contrary to most model predictions, in the first actuation the transformation temperatures are significantly higher than in the following cycles, which are stable. Moreover, if the temperature $T_h$ is exceeded, two separate actuations occur during heating: the first follows the path of the stable cycles; the second, starting at $T_h$, is similar to the first cycle. An interpretation of the phenomenon is given using some differential scanning calorimeter (DSC) measurements. The observed behavior emphasizes the need to build a more comprehensive constitutive model able to include these effects.

• International Journal of Aeronautical and Space Sciences
• /
• v.18 no.2
• /
• pp.236-244
• /
• 2017

In this study, the high-velocity impact penetration behavior of $[45/0/-45/90]_{ns}$ carbon/epoxy composite laminates was studied. The considered configuration includes a spherical steel ball impacting clamped circular laminates with various thicknesses and diameters. First, the impact experiment was performed to measure residual velocity and extent of damage. Next, the impact experiment was numerically simulated through finite element analysis using LS-dyna. Three-dimensional solid elements were used to model each ply of the laminates discretely, and progressive material failure was modeled using MAT162. The result indicated that the finite element simulation yielded residual velocities and damage modes well-matched with those obtained from the experiment. It was found that fiber damage was localized near the impactor penetration path, while matrix and delamination damage were much more spread out with the damage mode showing a dependency on the orientation angles and ply locations. The ballistic-limit velocities obtained by fitting the residual velocities increased almost linearly versus the laminate diameter, but the amount of increase was small, showing that the impact energy was absorbed mostly by the localized impact damage and that the influence of the laminate size was not significant at high-velocity impact.

• Journal of Korea Foundry Society
• /
• v.15 no.4
• /
• pp.388-396
• /
• 1995

This study has been conducted with the purpose of examining the fatigue crack growth characteristics of $Al_2O_3$ short fiber reinforced aluminum matrix composites made by squeeze casting process with different applied pressure and binder amount. Fatigue crack growth experiments have been performed under constant load amplitude method with a fixed load ratio. The rate of crack propagation was decreased with binder amount as well as applied pressure. Also fatigue crack growth path in matrix was changed from flat to rough mode with an increase of applied pressure. In the composites, fatigue crack was propagated to interface between matrix and reinforcement at 10MPa, but it was propagated to reinforcement at 20MPa. The major reason of thee result was considered that interfacial bonding force and microstructure of matrix were improved due to an increase of applied pressure. Localized ductile striation in the composites was observed at low growth rate region and such a phenominon was remarkable with an increase of applied pressure. At high growth rate region, the propensity of fracture appearance was changed from interfacial debonding to reinforcement fracture with an increase of applied pressure.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.4
• /
• pp.958-966
• /
• 1994

The postbuckling compressive strengths of $[0/90/\pm\theta]_s$ composite laminated cylindrical panels with various fiber angles and width-to-length ratios are characterized by the nonlinear finite element method. For the iteration and load-increment along the postbuckling equilibrium path a modified arc-length method in which the effect of failure can be considered is introduced. In the progressive failure analysis the maximum stress criterion and complete unloading model are used. Present finite element results show good agreement with experiments for $[0_3/90]_s$ cylindrical panel and $[0/\pm45/90/]_s$ plate. The postbuckling compressive strength of $[0/90/\pm\theta]_s$ composite laminated cylindrical panel is independent of the initial buckling stress but high in the panel with large value of the bending stiffness in axial direction. In the several cylindrical panels, it is observed that the prebuckling compressive failures occur and result into the collapse before the buckling.

• Steel and Composite Structures
• /
• v.21 no.4
• /
• pp.805-827
• /
• 2016

A new type of precast CFST column to RC beam braced frame is proposed in this paper. A series of shake table tests were conducted to excite a one-third scale six-story model for investigating the global seismic performance of this type of structure against earthquake actions. Particular emphasis was given to its dynamic property, global seismic responses and failure path. Correspondingly, a numerical model built on the basis of fiber-beam-element model, multi-layer shell model and element-deactivation method was developed to simulate the seismic performance of the prototype structure. Numerical results were compared with the measured values from shake table tests to verify the validity and reliability of the numerical model. The results demonstrated that the proposed novel precast CFST column to RC beam braced frame performs excellently under strong earthquake excitations; the "strong CFST column-weak RC beam" and "strong connection-weak member" anti-seismic design principles can be easily achieved; the maximum deflections of precast CFSTC-RCB braced frame satisfied the deflection limitations proposed in national code; the numerical model can properly simulate the dynamic property and responses of the precast CFSTC-RCB braced frame that are highly concerned in engineering practice.

• IE interfaces
• /
• v.18 no.3
• /
• pp.277-287
• /
• 2005

In this paper, we deal with a new techno-economic modeling and analysis for optical access networks. In deploying the fiber-to-the-home (FTTH) architecture, network planner needs to consider the following techno-economic issues: when do we need to upgrade existing local access network to FTTH network? how much do we invest to maximize profit? In order to answer these techno-economic questions, we need to consider the impact of emerging technologies and business environment. Toward this end, we develop a new techno-economic modeling to deal with the inherent complexity of technology evolution and cost economics. In particular, the new modeling approach provides us with an techno-economic analysis of technology alternatives such as ethernet passive optical network (E-PON) and wavelength division multiplex passive optical network (WDM-PON). In this analysis, we focus on the impact of critical factors such as the cost characteristic of proposed architecture and digital subscriber line (DSL) subscriber's churn-in to FTTH service and churn-out. We develop mixed integer-programming models for finding the evolution path of local access networks to broadband network architectures.