• 한국가스학회지
• /
• 제7권1호
• /
• pp.28-32
• /
• 2003

대체 facing material 소재로 유력시되는 FRP를 사용하여 facing material이 갖추어야할 압축, 인장 등 기계적 물성과, vapor barrier도, 화학적 안전성 등을 조사한 결과 모든 면에서 기존의 plywood보다 우수한 성질을 나타냄을 밝혔다. 본 연구의 결과로서 대체 facing material로 FRP를 사용할 경우 LNG 저장 탱크의 안전성이 향상되고 높은 vapor barrier기능으로 인해 탱크의 성능이 향상되는 등 다양한 장점을 나타냄을 알 수 있게 되었다. 따라서 본 연구의 결과는 LNG 저장 탱크의 성능을 개선하는데 기여하며, LNG 저장 탱크용 합판의 대체연구에 적극적으로 활용될 수 있을 것으로 사료된다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 봄 학술발표회 논문집
• /
• pp.75-80
• /
• 2001

This paper investigates the flexural behavior of reinforced concrete beams strengthened with externally bonded fiber reinforced plastic (FRP) sheets is investigated in this work. FRP is attractive for strengthening the RC beams due to its good tensile strength, low weight, resistance to corrosion, and easy applicability. A simple and direct analytical procedure for evaluating the ultimate flexural capacity of FRP strengthened reinforced concrete (SRC) beams is presented using the equilibrium equations and compatibility of strains. Upper and lower limits of FRP sheet area to ensure the ductile behavior are established. A parametric study is conducted to investigate the effects of design variables such as sheet area, sheet stiffness and strength, concrete compression strength, and steel reinforcement ratio. The analytical procedure is compared with results of experimental data available in the literature.

• 한국기계가공학회지
• /
• 제21권9호
• /
• pp.12-20
• /
• 2022

Delamination and burr defects are important problems in drilling fiber reinforced plastics. A method for measuring FRP drilling defects has been studied. Delamination and burr factors were defined as the relative length or area. Using these factors, the effects of tool shape and drilling conditions on delamination and burr were studied. In this study, the defects that occur when drilling a glass-carbon fiber hybrid composite were compared in terms of three factors. In the glass-carbon fiber hybrid composite, the effects of the feed rate and tool point angle on the delamination and burr factors were similar to those in previous studies. The diameter of the tool did not affect the defect factor. A circular burr was generated in a drill tool with a point angle of 184°, and a relatively small deburring factor was observed compared with a tool with a point angle of 140°.

• 한국구조물진단유지관리공학회 논문집
• /
• 제17권3호
• /
• pp.1-9
• /
• 2013

본 연구에서는 강섬유와 FRP 시트에 의한 충격 저항성능 향상 효과를 평가하기 위하여 고속 충격하중을 받는 2방향 RC 슬래브에 대한 유한요소 해석을 수행하였다. 유한요소 해석 프로그램으로는 충격해석에 탁월하다고 알려진 LS-DYNA를 사용하였으며, 실험결과와의 비교를 위하여 핀란드 VTT 연구소에서 수행한 고속 충격 실험과 동일한 조건으로 해석을 수행하였다. $2100{\times}2100{\times}250$ mm의 RC 슬래브에 강 (steel)발사체를 통해 충격하중을 가하였으며 발사체의 무게는 47.5kg, 속도는 134.9m/s였다. 본 연구에서는 별도의 재료부재에 대한 충격실험을 통해 해석에 사용할 재료 모델을 검증하였다. 본 해석에서는 SFRC의 비선형적 연화 현상을 모사하기 위해 elastic-plastic hydro model을 적용하였으며, 보통콘크리트와 FRP의 재료모델을 모사하기 위해서 concrete damage model과 orthotropic elastic model을 각각 사용하였다. 해석 결과, 제안된 해석 기법은 충분한 신뢰성을 가지고 있으며, 보강 재료와 보강 기법의 유효성을 평가하는데 효과적으로 적용할 수 있을 것으로 판단된다. 또한 강섬유와 FRP Sheets 보강방법은 고속충격하중에서 우수한 충격 저항 성능을 보여주는 것을 확인하였다.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1997년도 추계학술대회 논문집
• /
• pp.76-81
• /
• 1997

In the past polyester was usually used as the matrix of all fiber-reinforced plastic (FRP). Nowadays, however, epoxy resin has taken the place of polyester due to its superior properties. If the cutting properties of epoxy resin are unknown, It is difficult to find the optimum cutting conditions of all fiber-reinforced plastic such as CFRP. AFRP. GFRP. In this paper, I will study the cutting properties of epoxy resin by testing surface roughness.

• Composites Research
• /
• 제18권4호
• /
• pp.66-74
• /
• 2005

This paper reports new repair and strengthening mathod using improved material. This mathod have two type according to covering thickness of reinforcement. One type is near surface mounted FRP rod. Anther type is overay. Fiber Reinforced Plastic (FRP) materials has become very popular in recent years. FRP material used to rehabilitate many types of structures with superior characteristics such as high strength and stiffness and corrosion resistance. This strengthening mathod were used FRP rod which have better bond and shear strangth than current FRP rod. Development of FRP rod due to 3-D winding system. In addition, Ductile hybrid FRP has a certain plastic deformation and an elongation greater than 3% at maximum load is usually required for steel reinforcement in concrete structures. Moerover this mathod can be effective repair of base concrete by sprayed polymer mortar.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 봄 학술발표회 논문집
• /
• pp.973-978
• /
• 2003

This paper describes the experimental study on seismic strengthening effect of circular bridge columns with poor lap-splice details using FRP(Fiber Reinforced Plastic) wrapping, The as-built column suffered brittle failure due to the deterioration of lap-spliced longitudinal reinforcement without developing its flexural capacity or any ductility, The strengthening columns using FRP wrapping showed significant improvement in seismic performance due to FRP's confinement effect.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2006년도 정기 학술대회 논문집
• /
• pp.35-39
• /
• 2006

With a growing concern about the state of infrastructure worldwide, the demand for the development of reliable nondestructive testing techniques (NDT) is ever increasing. Among possible NDT techniques. microwave method is proven to be effective in fast and non-contact inspection of concrete structures and inclusions inside concrete. It is also found that the microwave method has a potential in detecting the delamination between fiber reinforced polymer (FRP) plate and concrete. On the other hand, ultrasonic method can be another way to find the delamination. In this paper, the research work needed for the development of a reliable microwave method and ultrasonic method is studied in actual measurements of concrete specimens reinforced with FRP. Concrete specimens are made with FRP and artificial delamination inside. A microwave measurement system with horn antennas with high center frequency and broad frequency bandwidth are used to image inside concrete specimens for the detection of debonding. between concrete and FRP. Also, the equipment of ultrasonic method which is commercialized are used at the same condition. Both of the results are analyzed in comparison of each other. Microwave and ultrasonic methods have been used for the detection of debonding between concrete and fiber-reinforced plastic (FRP).

• 공학교육연구
• /
• 제20권1호
• /
• pp.63-68
• /
• 2017

This research is as a case study of innovative engineering education system through idea factory of korea maritime and ocean university and deals with development of temperature-humidity control device (THCD) for fiber storage on composites in viewpoint of problem solving method. Fiber reinforced plastic (FRP) includes many variables on the composite manufacturing process. Above all, the interfacial adhesion between the fiber and the matrix acts as an important thing that decided mechanical property of the FRP, and also it is profoundly linked to external temperature and relative humidity. High void fraction leads to a result in interlaminar fracture. Therefore, in this research, to establish correlation between fiber reinforcement and fiber storage conditions of temperature and relative humidity we developed a THCD for fiber reinforcement. To evaluate performance of the THCD, glass fiber reinforced plastic (GFRP) is made under the extreme conditions each temperature $34^{\circ}C$, relative humidity 98 % and it can be said that there are the change of mechanical properties according to fiber storage conditions. As a result, the THCD showed sufficient possible application for understanding and applied research of composites field in material engineering. Also, we could check that the necessity of introduction of innovative system such as idea factory existed.

• 한국공간구조학회논문집
• /
• 제5권2호
• /
• pp.65-71
• /
• 2005

최근 노후화된 철근콘크리트 구조물에 대한 FRP를 이용한 보강공법의 적용이 증가하고 있다. 하지만 휨 보강에 대해서는 연구로 인해 정량적인 평가로 인해 효율적인 설계가 가능하지만, 전단보강의 경우에는 파괴메카니즘을 완전히 규명하지 못하는 상태이다. 본 연구에서는 전단보강근이 있는 철근콘크리트보에 매립형 CFRP를 전단보강하여 보강효과를 파악하고자 실험을 수행한 후, 실험결과를 토대로 분석 및 고찰을 통해 정량적인 보강효과를 도출하고자 한다. 시험체 제작시 실험변수로는 전단보강근의 간격과 보강방향으로 하여 시험체를 10개 제작하여 실험을 수행하였다. 실험결과, 전단보강근 간격과 보강방향에 따라 CFRP의 보강효과는 다소 차이를 보였다.