• 한국기계연구소 소보
• /
• s.19
• /
• pp.53-60
• /
• 1989

Hot upsetting experiments were carried out on presintered steel powder preforms in the temperature range 700- $950^{\circ}C$ to examine the hot deformation behavior. Following conclusions were drawn on the basis of the present study. -The flow stress during hot deformation is directly related to $\alpha$- $\gamma$ phase trasformation - The flow stress of ferrite is lower than that of austenite in the moderate temperature range 800- $900^{\circ}C$ for most alloys used in the present study - Major restoration behavior during hot deformation in the ferrite range is dynamic recovery.

• Resources Recycling
• /
• v.11 no.1
• /
• pp.3-8
• /
• 2002

In order to make the high purity Mn$_3$O$_4$powder for the raw material of soft ferrite, Mn is extracted from the dust and the extracted solution is refined. The dust is generated in producing a medium-low carbon ferromanganese and contains 90% Mn$_3$O$_4$. Mn$_3$O$_4$in the dust was reduced into MnO by roasting with charcoal. Injection of the 180g/L of the reduced dust into 4N HCI solution increased pH of the leaching solution higher than 5 and then a ferric hydroxide was precipitated. Because the ferric hydroxide co-precipitates with Si ion etc, Fe and Si ion was removed from the solution and the about 10% Mn solution was obtained. The solution was diluted with water to Mn-15000 ppm and $NH_4$F was injected into the diluted solution at $70^{\circ}C$ to the F-3000 ppm. As a result, Ca ion is precipitated as $CaF_2$and the residual concentration of Ca was 14 ppm. Injection of the equivalent (NH$1.5M_4$)$_2$$CO_3$solution as 2 L/min at $25^{\circ}C$ into the above solution precipitated a fine and high purity $MnCO_3$powder. The deposition was filtrated and roasted at $1000^{\circ}C$ for 2 hours. As a result, $MnCO_3$powder is converted into $Mn_3$$O_4$powder and it had $8.2\mu$m of median size. The final production is above 99% $Mn_3$$O_4$powder and it satisfied the requirement of high purity $Mn_3$$O_4$powder for a raw material of soft ferrite.

• Polymer(Korea)
• /
• v.29 no.2
• /
• pp.156-160
• /
• 2005

$\alpha,\omega-Vinyl$ poly (dimethyl-methylphenyl) siloxane prepolymer (VPMPS ) was prepared by the equilibrium polymerization of octamethylcyclotetrasiloxane $(D_4)$, 1,3,5-trimethyl-1,3,5-triphenylcyclotrisiloxane $(D_3^{Me,Ph)$, and 1,1,3,3-tetramethyl-1,3-divinyldisiloxane (MVS). And also, of $\alpha,\omega-hydrogen$ poly(dimethyl-methyl)siloxane prepolymer (HPDMS) as end blocker was prepared from octamethylcyclotetrasiloxane $(D_4)$, 1,3,5-trimethylcyclotrisiloxane $(D_3^:Me,H})$, and 1,1,3,3-tetramethyldisiloxane (MS). Nickel ferrite nanoparticles having spinel magnetic material was prepared by the sol-gel method using PAA as a chelating agent. Poly(organosiloxane) rubber nanocomposite containing silica and nickel ferrite ultrafine powder modified with 1,3-divinyltetramethyldisilazane (VMS) was prepared by compounding VPMPS, HPDMS, and catalyst in high speed dissolver. The mechanical properties, heat dissipating away characteristics, and volume resistivities for POX-30 and POX-50 were measured.

• Journal of the Microelectronics and Packaging Society
• /
• v.9 no.4
• /
• pp.47-53
• /
• 2002

In this study, two different (NiCuZn)-ferrite which were fabricated by using ultra-fine powders synthesized by the wet processing and conventionally commercialized powder, were investigated and compared each other in terms of the low temperature sintering and electromagnetic properties. Composition of x and w in $(Ni_{0.4-x}Cu_xZn_{0.6})_{1+w}(Fe_2O_4)_{1-w}$ were controlled as 0.2 and 0.03, respectively. The sintering temperature were $900^{\circ}C$ for ultra-fine powders by way of initial heat treatment and $1150^{\circ}C$ for commercialized powders. The (NiCuZn)-ferrite by ultra-fine powders showed love. sintering temperature than that of commercialized powders by over $200^{\circ}C$, and excellent electromagnetic properties such as the quality factor which is a important factor in the multi-layered chip inductor. In addition, characteristics of B-H hysteresis, crystallinity, microstructure and powder morphology were analyzed by a vibrating sample method(VSM), x-ray diffractometer(XRD), transmission electron microscope (TEM) and scanning electron microscope(SEM).

• Proceedings of the Korean Magnestics Society Conference
• /
• 2000.09a
• /
• pp.433-440
• /
• 2000

Barium ferrite particles were synthesized from Ba(NO$_3$)$_2$, Fe(NO$_3$)$_3$ and KOH mixed solutions using hydrothermal crystallization in supercritical water. The experimental apparatus for production of barium ferrite is a flow-type apparatus. Fine barium ferrite particles were produced because supercritical water causes the metal hydroxides to be rapidly dehydrated before significant growth takes place. The effects of Fe/Ba ratio and reaction time on the formation, particle size, and magnetic properties of barium ferrite were studied. When Fe/Ba ratio were varied from 0.5 to 12, single-phase barium ferrite powder was only produced in the range of 0.5〈Fe/Ba〈2. Also, with elevating reaction time, the BaO.6Fe$_2$O$_3$ particle size grew smaller. Especially, uniform barium hexaferrite particles of size 100-200nm were obtained at 80sec. In this study, therefore, single-phase barium ferrite particles are highly stable and can be produced continuously in a reaction time of less then 2min.

• Journal of the Korean Society of Safety
• /
• v.18 no.2
• /
• pp.46-49
• /
• 2003

The magnetic polishing is the useful method to finish some machinery fabrications by using magnetic power. This method is one of the precision techniques and has m aim for clean technology in the transportation of the pure gas in the clean pipes. The magnetic abrasive polishing method is not so common in the field of machine that it is not known to widely. There are rarely researcher in this field because of non-effectiveness of magnetic abrasive. Therefore, in this paper we deals with the development of the magnetic abrasive with the use of Ba-Ferrite. In this development, abrasive grain WA has been made by using the min bond fabricated at low temperature. And magnetic abrasive powder was fabricated from the Ba-Ferrite which was crushed into 200 mesh. The XRD analysis result shows that only WA abrasive and Ba-Ferrite crystal peaks were detected, explaining that resin bond was not any more to contribute chemical reaction. From SEM analysis, we found that WA abrasive and Ba-Ferrite were strongly bonding with each other.

• Journal of the Korean Magnetics Society
• /
• v.6 no.4
• /
• pp.251-257
• /
• 1996

A coercivity of barium ferrite (BaM) tape was found to be higher than the coercivity of BaM powder, This difference is in the range of 50 Oe to 600 Oe, which depends on substituted cations. physical properties of powder, and preparation conditions of the tape. The coercivity difference is attributed to both particle stacking and adsorption of organic solvent on particle surface. Regardless of substituted cations, the coercivity of longitudinally oriented BaFe tape was higher than that of BaM powder by a range of 100 Oe to 120 Oe, which is caused by particle stacking' During the active adsorption process on preparation of magnetic paint, where MEK (methyl ethyl ketone), TOL (toluene) and CHO (cyclohexanone) were used, chemisorption of solvents on the surface of substituted BaFe particle occurred to form polymeric compounds surrounding the particle. An increase in coercivity, caused by the solvent adsorption, was significant for Co-substutited BaM tape. Among these solvents CHO was the most effective one in increasing the coercivity of the Co-Ti substituted BaM tape.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1993.11a
• /
• pp.54-55
• /
• 1993

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1993.11a
• /
• pp.56-57
• /
• 1993

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 1994.04c
• /
• pp.16-17
• /
• 1994