• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.1100-1105
• /
• 2010

The high speed line and conventional line are a single-phase AC feeding system; and power supplies of different phases meet at SS(SubStation)s or SP(Sectioning Post)s. These sections should be negotiated with the main circuit breaker in the traction vehicle switched off, whereby the length of the neutral zone prevents the pantographs shunting adjacent overhead line section. In order for electric railway vehicles to make power running there, there must be a power supply changeover section (approx. for 1km), where a changeover switch changes a power supply to the other power supply of a train running direction sequentially. For a thorough changeover switching control, the precise train position detection is necessarily required. In this paper, to realize the ground-based train position detection method, configuration scheme of train position detection equipment is suggested by using track circuit and axle counter.

• Journal of Biosystems Engineering
• /
• v.38 no.3
• /
• pp.215-221
• /
• 2013

Purpose: Opuntia Humifusa has been used in the food and beauty industry after removing spines and glochids clearly. This study compared the methods used in removing spines and analyzed the design factors for developing a spine removal device. Method: This study compared the spine removal ratios in accordance with the length of brush, water spray pressure, the number of water spray, and the size of Opuntia Humifusa in a rotating brush device and a water spray device. In addition, this study compared the reversal ratios according to the inclination angle of a conveyor, the drop height of Opuntia Humifusa, and the speed of the conveyor to analyze the reversal factors. Results: The spines were not removed clearly in the rotating brush method, and the glochids were nailed deeply. The spine removal ratio was 96.9% with the water spray pressure of 20 $kgf/cm^2$ and the conveyor speed of 10 cm/s in the water spray method. The number of water spray was correlated with the spine removal ratio, and the average spine removal ratio was 95.6% with three cycles of water spray. The reversal ratio was 97% with the inclination angle of the conveyor $20^{\circ}$, the drop height of 380 mm, and the conveyor speed of 10 cm/s. Conclusions: In order to develop a Opuntia humifusa spine removing device, this study compared the rotating brush and water spray methods. As a result, each spine removal performance of the rotating brush and water spray methods was 96.9% and 95.6%, respectively. Although the performance of the rotating brush method was slightly higher than that of the water spray method, the water spray method was suitable for removing spines from stem because the epidermis of stem was damaged and the glochids were nail deeply in the rotating brush method. Further studies on appropriate arrangement of spray nozzles, maintaining the optimal water spray pressure, the speed and angle control of the feeding conveyor, and devices for inducing the stem to the center will be needed in combining the water spray device and the reversal device.

• Journal of Powder Materials
• /
• v.10 no.5
• /
• pp.349-352
• /
• 2003

This study examined the correlation of various operational factors including reaction temperature and the quantity of reductant and diluent with the characteristics of powder using $K_2$ TaF$_{7}$ as feed materials, Na as a reductant and KCl/KF as a diluent. Also to control the particle size and shape, external supply system developed, it can provide a feed material and a reductant at a fixed quantity and evaluated the characteristics of tantalum powder. When the external supply system was applied instead of the batch type process that charges feed material, reductant and diluent at the same time, it was possible to induce regular reduction reaction between feed material and reductant, which increased the recovery rate and reduced the mixture of impurities. In particular, the application of the external supply system enabled the control of reaction temperature and reaction speed according to the feeding rate of feed material during reduced reaction, and resultantly it enabled the manufacturing of granular-shaped powder with a regular granularity of 2∼3 ${\mu}{\textrm}{m}$ and purity of 99.5%.

• Proceedings of the Korean Society of Near Infrared Spectroscopy Conference
• /
• 2001.06a
• /
• pp.3103-3103
• /
• 2001

NIR has been extensively used to predict directly measurable properties of materials that are important to the appropriate industries. Commonly, NIR is used to perform fast, routine tests to improve control response as against the response time for the (normally chemical) base test. This paper discusses the use of NIR to measure indirect properties of materials. In these cases, the pure chemical or physical tests are either unable measure the appropriate parameters (eg GMO modification) or there are mitigating effects that are not properly addressed by the base tests. In particular, we looked at the digestible portion of amino acids within meat and bone meal. This is the desired response measurement by end-users of the product (intensive livestock producers) but is currently unable to be offered as a measurement by producers. The base test method is by controlled feeding trials. These are somewhat cumbersome, taking 2-3 months, involving several sets of animals, and considerable expense. A shortened test (feed trial based) would be of little use, as the precision blows out over short period feeding trials. For example, a rat ileal digestibility test requires around 2 months, and costs some $USD1000. This is clearly impractical test for a producer involved in continuous production, with a 1-2 day turn around. While the amino acid abundance is accessible chemically, the uptake of amino acids into usable material by mammalian species is not simply related to the measured abundance within the material. There are many co-related material properties that might help or hinder uptake, some chemical based (eg protein damage), some indirect (eg palatability), some physiological (intestinal tract response vs speed of throughput). We discuss the approaches taken to provide a suitable reference data set, and present the derived prediction and validation relationships.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.13 no.1
• /
• pp.5-14
• /
• 2003

Principles of a novel pulse growing method are described. The method realized in the crystal growing on a seed from melts under raw melt feeding provided a more reliable control of the crystallization process when producing large alkali halide crystals. The slow natural convection of the melt in the crucible at a constant melt level is intensified by rotating the crucible, while the crystal rotation favors a more symmetrical distribution of thermal stresses over the crystal cross-section. Optimum rotation parameters for the crucible and crystal have been determined. The spatial position oi the solid/liquid phase interface relatively to the melt surface, heaters and the crucible elements are considered. Basing on that consideration, a novel criterion is stated, that is, the immersion extent of the crystallization front (CF) convex toward the melt. When the crystal grows at a <> CF immersion, the raised CF may tear off from the melt partially or completely due to its weight. This results in avoid formation in the crystal. Experimental data on the radial crystal growth speed are discussed. This speed defines the formation of a gas phase layer at the crystal surface. The layer thickness il a function of time a temperature at specific values of pressure in the furnace and the free melt surface dimensions in the gap between the crystal and crucible wall. Analytical expressions have been derived for the impurity component mass transfer at the steady-state growth stage describing two independent processes, the impurity mass transfer along the <> path and its transit along the <> one. The heater (and thus the melt) temperature variation is inherent in any control system. It has been shown that when random temperature changes occur causing its lowering at a rate exceeding $0.5^{\circ}C/min$, a kind of the CF decoration by foreign impurities or by gas bubbles takes place. Short-term temperature changes at one heater or both result in local (i.e., at the front) redistribution of the preset axial growth speed.

• Journal of Ocean Engineering and Technology
• /
• v.25 no.6
• /
• pp.1-8
• /
• 2011

This paper describes a new method for a digital gas metal arc welding (GMAW) system. The GMAW system is an arc welding process that incorporates the GMAW power source (PS-GMAW) with a wire feed unit (WFU). The PS-GMAW requires an electric power of constant voltage. A constant magnitude is maintained for the arc current by controlling the wire-feed speed of the WFU. A mathematical model is derived, and a self-tuning fuzzy proportional-integral-derivative (PID) controller is designed and applied to control the welding current. The electrode wire feeding mechanism with this controller is driven by a DC motor, which can compensate for both the molten part of the electrode and undesirable fluctuations in the arc length during the welding process. By accurately maintaining the output welding current and welding voltage at constant values during the welding process, excellent welding results can be obtained. Simulation and experimental results are shown to prove the effectiveness of the proposed controller.

• Journal of Biosystems Engineering
• /
• v.43 no.4
• /
• pp.379-385
• /
• 2018

Purpose: Postharvest handling of onions (harvesting, cleaning, grading, cooling, storing, and transport) should be performed continually to reduce costs and improve quality. The purpose of this study is to a) determine the design parameters and operating conditions of anion auto-dumping that constitutes a key component of the postharvest bulk handling machinery system, and b) to perform a performance test with the auto-dump prototype system. Methods: Kinematic analyses and computer simulations of the auto-dump mechanism were applied to analyze the operating conditions and design parameters. Results: The optimum working condition for the auto-dump was determined from kinetic analyses. In addition, the interaction between the velocity of the hydraulic cylinder and the angular velocity of the auto-dump were analyzed in order to control the bulk handling machinery system. The acting forces and optimum operating conditions of the hydraulic cylinder were determined by analyzing the forces related to the mass of inertia of the auto-dump assembly during rotation. The method of controlling the feeding rate of onions in terms of the uniformity of the stacking pattern and the control of the entire system was better than the two-stage method of controlling the rotational speed of the auto-dump. Based on the performance test with the prototype for the auto-dump, the stacking pattern and rigidity of the system were analyzed. Conclusions: These results would be of great importance in the postharvest bulk handling machinery system for onions.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.4 no.1
• /
• pp.43-49
• /
• 2002

We have cloned cDNAs encoding toxin from the spider, Araneus ventricosus, and constructed a recombinant baculovirus expressing the insecticidal toxin. The cDNAs encoding toxin were cloned from the cDNA library of A. ventricosus. Sequence analysis of the cDNAs encoding the toxin of A. ventricosus revealed that the 240 bp cDNA for AvTox-1 and 192 bp cDNA for AvTox-2 have an open reading frame of 80 and 64 amino acid residues, respectively. The deduced protein sequence of the toxin genes of AvTox-1 and AvTox-2 was aligned to that of the snack Anemonia sulcata and scorpion Centruroides limpidus limpidus, respectively. Northern blot analysis indicated that AvTox-2 toxin gene showed a fat body-spe-cific expression pattern at the transcriptional level. Furthermore, we have explored the possibility of improving baculovirus by incorporating the A. vontricosus toxin gene into Bombyx mori nuclear polyhedrosis virus genome under the control of polyhedrin promoter, The AvTox-2 toxin gene was expressed as approximately 5.8 kDa band in the recombinant baculovirus-injected silkworm larvae. Bioassays with the recombinant virus expressing AvTox-2 on 5th instar silkworm larvae demonstrated a decrease in the time to kill $(LT_{50} days)$ compared to wild-type BmNPV-Kl $(LT_{50} 6.72 days)$ in the injection of 10 viruses. These results indicate that A. ventricosus toxin is a novel member of the spider toxin family, suggesting that the toxin gene can be used in recombinant baculoviruses to reduce insect feeding damage and increase the speed of insect kill.

• Journal of Biomedical Engineering Research
• /
• v.32 no.2
• /
• pp.127-133
• /
• 2011

Arteria radialis is a branch of the brachial artery extending down the forearm around the wrist where it closes to skin surface. In the oriental medicine, the skin above arteria radialis has an important role because oriental medicine practitioners put their finger tips on the area, and diagnose patient's health conditions by feeling the pulsation of the arterial contraction. The finger tip diagnostic method relies on subjective decision of the practitioner; and there is a need to develop an objective diagnostic modality. The pulsation of the arterial contraction appears not only a movement on the site but also as temperature fluctuation due to pulsatile feeding of warmer blood. The goal of this study is to demonstrate a feasibility of using an infrared camera quantitatively to detect the temperature fluctuation on the skin. Clinical important three different areas, called chon, gwan, chuk, near a wrist where the arteria radialis reaches close to skin surface are marked with small pieces of surgical tape. A high-speed and high-resolution infrared camera with a 3 cm of field of view measures these areas for 10 second at 200 frames per second with a 320*240 pixel size. The pulsatile temperature fluctuation is calculated after passing a band pass filter to remove any stationary temperature over 10 second. The temperature fluctuation of a healthy male volunteer is measured at a room temperature as a control, and is compared with another measurement performed after 20 minutes staying in a room at a 40 degree Celsius. This comparison is repeated for three times, and indicates that the fluctuation increases after staying 20 minutes in the warm room. This increase becomes smaller when the person stays in the warm room with an acupuncture treatment that decreases body temperature. So that an objective diagnostics on the site may become feasible.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.4
• /
• pp.748-757
• /
• 2007

This paper is intended to solve the technical problem that fails in large-capacity induction motor starting due to serious voltage drop during starting period. One induction motor that is established already can reach in steady-state using reactor starting method but the voltage magnitude of PCC (point of common coupling) has dropped down a little. When the same capacity induction motor is installed additionally in the PCC, where the existing induction motor is operating, voltage drop becomes more serious by starting of additional induction motor. As a result, the additional induction motor fails in starting. Therefore, voltage compensation method is proposed so that all of two induction motors can be started completely. First, modeling technique is described in order to implement starting characteristics of large induction motor. And then, this paper proposes strategic starting scheme by proper voltage compensation that use no-load transformer tap control (NLTC) and step voltage regulator (SVR) for starting of two large induction motors successfully and improving the feeding network voltage profile during the starting period. The induction motor discussed in this paper is the pumped induction motor of 2500kVA capacity that is operating by KOWACO (Korea Water Resources Corporation). Modeling and simulation is conducted using PSCAD/EMTDC software.