• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.950-955
• /
• 2005

This paper describes an intelligent filler wire feeding device which can control 3- dimensional seam tracking and the filler wire speed by measuring the gap position and the joint gap width in laser welding. By means of visual sensor controlled filling the missing material into the joint gap and 3 dimensional seam tracking, lineup errors from manufacturing tolerances and the repeatability of lineup jigs and weld robot can be balanced and at an even seam quality which avoids weld defects. In this paper, we assessed weld quality in 2mm sheets of A16061 which had various gap width by using the intelligent filler wire feeding device.

• Journal of Electrical Engineering and Technology
• /
• 제6권2호
• /
• pp.215-225
• /
• 2011

In this paper, a buck DC-DC bridge converter is used as a power factor correction (PFC) converter for feeding a voltage source inverter (VSI) based permanent magnet brushless DC motor (PMBLDCM) drive. The front end of the PFC converter is a diode bridge rectifier (DBR) fed from single phase AC mains. The PMBLDCM is used to drive the compressor of an air conditioner through a three-phase voltage source inverter (VSI) fed from a variable voltage DC link. The speed of the air conditioner is controlled to conserve energy using a new concept of voltage control at a DC link proportional to the desired speed of the PMBLDC motor. Therefore, VSI operates only as an electronic commutator of the PMBLDCM. The current of the PMBLDCM is controlled by setting the reference voltage at the DC link as a ramp. The proposed PMBLDCM drive with voltage control-based PFC converter was designed and modeled. The performance is simulated in Matlab-Simulink environment for an air conditioner compressor load driven through a 3.75 kW, 1500 rpm PMBLDC motor. To validate the effectiveness of the proposed speed control scheme, the evaluation results demonstrate improved efficiency of the complete drive with the PFC feature in a wide range of speed and input AC voltage.

• 한국정보통신학회논문지
• /
• 제16권11호
• /
• pp.2474-2479
• /
• 2012

유도 모터의 센서리스 벡터 제어시스템은 모터의 시정수를 이용하여 자극의 위치를 추정하는 제어시스템으로 중고속 영역의 경우 제어가 잘 구현된다. 그러나 저속 영역의 경우 모터로부터 얻는 전압 정보가 작아 센서리스 벡터제어 구현이 어렵다. 본 논문에서는 3Hz이하의 저속영역에서 센서리스 벡터제어의 문제점을 개선시키기 위한 줌잉 알고리즘을 이용한 퍼지 논리 제어기를 제시하였으며 제어기 성능이 향상됨을 실험을 통하여 확인하였다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 추계학술발표대회 개요집
• /
• pp.132-134
• /
• 2005

The friction surfacing system which has been successfully developed in RIST has both position control and force control by using hydraulic cylinder. In friction surfacing process mechtrode rotation speed(N) and feeding speed($V_{z}$), travelling speed($V_{x,y}$) are of critical importance for the width and thickness of the coating. As a result of DOE with developed system, the main effect of coating thickness is a rotation speed of mechtrode.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.121.4-121
• /
• 2001

We propose an off-line methodology for detecting a faulty backup roll that generates eccentricity components, under the condition that the feeding velocity, equivalently the angular velocity of roll, is not constant. From a newly devised speed angle conversion algorithm, we transform all process data into those of a virtual process under a constant feeding speed. This indirectly way, we can apply a spectral analysis to the original process. In addition, we develop an online detection method of roll eccentricity based on newly designed PLG sensor. This PLG sensor is robust because of applying magnetic proximity sensnors and non-contact measurement method.

• 한국통신학회논문지
• /
• 제21권2호
• /
• pp.313-325
• /
• 1996

This paper presents a new architecture for full-search block-matching motion estimation. The architecture is based on linear systolic arrays. High speed operation is obtained by feeding reference data, search data, and control signals into the linear systolic array in a pipelined fashion. Input data are fed into the linear systolic array at a half of the processor speed, reducing the required data bandwidth to half. The proposed architecture has a good scalability with respect to the number of processors and input bandwidth when the size of reference block and search range change.

• 한국정보통신학회논문지
• /
• 제14권10호
• /
• pp.2299-2304
• /
• 2010

유도 모터의 센서리스벡터 제어시스템은 모터의 시정수를 이용하여 자극의 위치를 추정하는 제어 시스템으로서 중 고속영역의 경우 벡터 제어가 잘 구현된다. 그러나 저속의 경우 모터로부터 얻는 전압정보가 너무 작아서 벡터 제어기의 구현이 어렵다. 본 논문에서는 슬립 주파수 추정을 이용하여 저속에서의 센서리스벡터제어 문제점을 개선시켜 광범위한 속도 영역에서 벡터제어가 가능한 센서리스 벡터제어기를 설계하였다. 제어기의 성능은 실험을 통하여 확인하였다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1999년도 제14차 학술회의논문집
• /
• pp.244-247
• /
• 1999

This paper presents a methodology of the technique for controlling DC motor drive by implementation of 2-quadrant operating mode which can ensure the torque controlling and speed with response time less than 2 seconds at all loading conditions. By implementation of BRM technique, energy is fed with definite values of BRM 256 bits, with different patterns of high accuracy, and fixing scan time at 0.667 ms, the ripple is less than 1%, thus high efficiency can be achieved, from the consequence of the accuracy of energy feeding at low current. The stability of the whole system can be determined from circle criterion by root locus method . The instant reverse direction of rotation can be done by decreasing the energy to the lowest level while motor is running with no load and variable load at the speed about 100-120 rpm and 50-60 rpm.

• Journal of Biosystems Engineering
• /
• 제19권4호
• /
• pp.311-317
• /
• 1994

Warts and barks of apple trees were vector of White rot. Two devices removing warts and barks for the use of pest control on apple trees were developed and evaluated in this study, and their results are as follows ; 1. A total of 148 warts were examined to determine the average size. About 35 percent of the examined warts were 6~8mm long, 4~8mm wide and 4~6mm thick in size. About 30 percent of the examined warts were 4~6mm long, 2~4mm wide and 6~8mm thick in size. 2. Seventy-one percent of the examined barks removed were 4~8mm in thickness. 3. A blade with 30 degree of cutting angle required 3 to 22 percent less cutting energy than those with 15 and 45 degrees of cutting angles. 4. The cutting torque decreased from 31 N-cm to 12 N-cm with an increase of cutting speed from 26cm/s to 104cm/s for a feeding speed of 0.31 mm/s with the blade angle of 30 degrees. 5. The cutting torque increased from 6N-cm to 32N-cm with an increase of branch diameter from 6mm to 14mm for a feeding speed of 0.31 mm/s with the blade angle of 30 degrees. 6. Two devices mounted on a mower for removing warts and barks were evaluated and proved effective.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1990년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 26-27 Oct. 1990
• /
• pp.292-297
• /
• 1990

An anti-swing controller for an overhead crane in the stop position is designed. The developed anti-swing controller improves on the poor damping characteristics of overhead crane by feeding back the crane acceleration as a function of swing angular speed. The experimental results show that this crane using the proposed controller yields small stop position error and rapid damping response characteristics.