• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.14 no.1
• /
• pp.26-33
• /
• 2014

This study addresses the control problem of an unmanned aerial vehicle (UAV) during the transition period when the flying mode changes from hovering to translational motion in the horizontal plane. First, we introduce a compensation algorithm that improves height stabilization and reduces altitude drop. The main principle is to incorporate pitch and roll measurements into the feedforward term of the altitude controller to provide a larger thrust force. To further improve altitude control, we propose the fuzzy logic controller that improves system behavior. Simulation results presented in the paper highlight the effectiveness of the proposed controllers.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.11
• /
• pp.2049-2055
• /
• 2011

In this paper a new current control method is proposed for the discontinuous conduction mode of boost converter. The proposed method using a current gain feedforward compensation adjusts a measured inductor current value and then, calculated an average current precisely in the discontinuous conduction mode as well as continuous conduction mode. By applying the proposed method, the current measurement error is significantly reduced to 2% regardless of the operating points. The proposed method is analyzed and its performance is investigated in simulation. To verify the feasibility of the proposed scheme, a 10kW 3-phase interleaved boost converter was built and experimental results are matched to the simulation results.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.8
• /
• pp.705-713
• /
• 2014

In this paper, we propose a novel velocity ripple controller using phase compensation feedforward control. Velocity ripples result in many kinds of performance degradations in manufacturing machines, especially such as ultra-precision roll lathes. The generation of velocity ripple in constant velocity control comes from various causes, such as electrical torque ripples, mechanical worn out, inconsistent mass center, etc. Conventional researches about ripple is mainly for reducing torque ripple in actuator level, which is only one of reasons for velocity ripples, so in this study, we focus on eliminating velocity ripples in upper level controller using phase compensation feedforward controller. The proposed algorithm is composed of several modules, such as ripple extractor, phase adjuster and phase follower etc. The suggested algorithm can be easily extended, and it shows a superior performance in the experiments of ultra-precision roll lathes.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.2
• /
• pp.83-91
• /
• 2004

This paper illustrates the feasibility and the effectiveness of the disturbance feedforward compensation control proposed in the previous paper. The compensator is designed experimentally by means of the Multiple Filtered-x Least Mean Square algorithm. A 2-DOF active magnetic bearing system subject to base motion is built and the compensation control is applied. The experimental results demonstrate that the compensation control reduces the air-gap responses within 10$%$ of those by the feedback control alone without increasing the control inputs.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.4A
• /
• pp.197-204
• /
• 2012

We propose a new scheme combining the compensation of HPA nonlinearity and the calibration of the path imperfections in the downlink OFDM smart antenna systems. We use a two term third-order polynomial (without second-order term) and the feedforward method for compensation and calibration to make each path of the antenna array have equal characteristics. Since the proposed scheme does not alter the base-band signal, it can be applied to the smart antenna system independently of the base-band signal processing section. The result of computer simulations shows that, with the addition of only one third-order term, the adverse nonlinear effects can be effectively compensated, and the those of linear imperfections can be calibrated as well.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.488-493
• /
• 2005

In gun stabilization systems, the torque comes from the unbalance mass of gun and the base acceleration is an important source of disturbance which degrades stabilization performance. Fatigue of gear train is another important factor affecting structural safety problems. In this paper, a feedback control gain is designed by optimal control weighting to difference between motor and gun velocity, and a feedforward controller using FXLMS algorithm is adopted to investigate those problems. Experimental results show that the feedforward compensator based on FXLMS can reduce the disturbance effects. The directional convergence property according to initial conditions of the FXLMS is also shown through experiments.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.2
• /
• pp.74-82
• /
• 2004

In this paper, a disturbance feedforward compensator design technique is proposed for an active magnetic bearing system subject to base motion for attenuating disturbance responses. In the consideration of the requirements on the model accuracy in the model based compensator designs, an experimental feedforward compensator design based on adaptive estimation by means of the Multiple Filtered-x least mean square(MFXLMS) algorithm is proposed. The performance and the effectiveness of the proposed technique will be presented in the succeeding paper in which the proposed technique is applied to a 2-DOF active magnetic bearing system subject to base motion.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.294-297
• /
• 1994

A robust position tracking controller of the BLDDM sensitive to the load torque disturbance and inertia variation is constructed It is consisted of the linear feedback controller and the nonlinear feedforward compensator using the neural network. With effietive feedforward compensation of neural network, the robust position control can be obtained, which is verified by computer simulations.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.49 no.4
• /
• pp.9-17
• /
• 2012

In this paper, we show the memory effect of the high-power amplifiers for wied-band signals, present a compensation method for the nonlinearity combined with memory effect, and analyze its performance. For the modeling and the compensation of the nonlinear high-power amplifier with memory effect, we investigate the Volterra series model, the Wiener model, and the Hammerstein model. As a compensator scheme, we propose a digital feedforward technique. Compared to analog feed-forward scheme, the proposed scheme has better stability and adaptability to the environmental changes. It has a simpler structure than the conventional digital nonlinear compensation schemes. The result of computer simulations using ADS of the Agilent shows that spectral re-growth is suppressed by more than 20 dB, which amounts to at least 10 dB back-off. Considering the compensation performance, implementation complexity, and convergence rate, we could conclude the Wiener model is most suitable for the proposed scheme.

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.7
• /
• pp.590-596
• /
• 2004

A passivity-based dynamic output feedback controller design is considered for a finite collection of non-square linear systems. Design of a single controller for a set of plants i.e. simultaneous stabilization is an important issue in the area of robust control design. We first determine a squaring gain matrix and an additional dynamics that is connected to the systems in a feedforward way, then a static passivating control law is designed. Consequently, the actual feedback controller will be the static control law combined with the feedforward dynamics. A necessary and sufficient condition for the existence of the parallel feedforward compensator is given by the static output feedback formulation. In contrast to the previous result [1], a technical condition for constructing the parallel feedforward compensator is removed by proposing a new type of the parallel compensator.