• IE interfaces
• /
• v.9 no.1
• /
• pp.53-62
• /
• 1996

The Delphi method is widely used for long and middle range forecasting in management science. It is a method by which the subjective data of experts are made to converge using statistical analysis. The Fuzzy Delphi Method(F.D.M.), anew application of the Delphi method using Triangular Fuzzy Numbers(T.F.N.), can help to predict the uncertainty, synthesize the opinion and calculation of those assumed dissemblance index and fuzzy distance. Furthermore, the programming of the F.D.M. process to feed paper and data back to experts can make them more accurately predict the various information.

• The Journal of the Acoustical Society of Korea
• /
• v.29 no.5
• /
• pp.303-313
• /
• 2010

This paper describes an acoustic communication receiver structure, which is designed for QPSK (Quadrature Phase Shift Keying) signal with 25 kHz carrier frequency and 5 kHz symbol rate, and takes samples from received signal at 100 kHz sampling rate. Based on the described receiver structure, optimum design parameters, such as number of taps of FF (Feed-Forward) and FB (Feed-Back) filters and forgetting factor of RLS (Recursive Least-Square) algorithm, of joint equalizer are determined to minimize the BER (Bit Error Rate) performance of the joint equalizer output symbols when the acquisition data in shallow water using implemented acoustic transducers is decimated at a rate of 2:1 and then enforced to the input of receiver. The transmission distances are 1.4 km, 2.9 km, and 4.7 km. Analysis results show that the optimum number of taps of FF and FB filters are different according to the distance between source and destination, but the optimum or near optimum value of forgetting factor is 0.997. Therefore, we can reach a conclusion that the proper receiver structure could change the number of taps of FF and FB filters with the fixed forgetting factor 0.997 according to the transmission distance. Another analysis result is that there are an acceptable performance degradation when the 16-tap-length simple filter is used as a low-pass filter of receiver instead of 161-tap-length matched filter.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.6
• /
• pp.42-49
• /
• 1994

One of the parameters that influence the productivity of every industry, involved in metal cutting, is the chip from ; continuous or broken chip. Chip form varies according to machining conditions, material used, tool geometry and chip breaker geometry. Therefore, in this study we carried out the experiment on the chip control in machining STS304 using an attached obstruction type chip breaker. Namely, with the change of a chip breaker distance, chip breaker angle, cutting characteristics in machining STS304 which is well-known as a machining difficult material and produces a saw-toothed chip. The results of the experiment are as follows : 1. The chip breaker distance and angle under which the preferred chip is produced, show 1.5mm and 60 .deg. , while chip breaker angle in machining an ordinary steel was well-known 45 .deg. . 2. During the cutting process, the change of feed than the change of velocity was applied as cutting conditions, effects more clearly on the chip breaking. 3. Considering a whole surface roughness, it is not advisable to apply chip breaker mentioned above for precision cutting.

• Journal of Animal Science and Technology
• /
• v.60 no.2
• /
• pp.1.1-1.6
• /
• 2018

Background: Maize fodder is being used as staple feed for livestock but it lacks protein and essential amino acids; lysine and tryptophan. Intercropping maize with leguminous soybean crop is promising technique under limited land resources of South Korea but it can only give considerable advantages when adequate distance is provided between corn and soybean rows. Main aim of present study was to find-out adequate distance between corn and soybean seeding rows for optimum growth, yield and nutritive value of intercropped forage. Methods: Different interrow distances between corn and soybean were evaluated under four treatments, viz. 1) Corn sole as positive control treatment 2) Zero cm between corn and soybean (control); 2) Five cm between corn and soybean; 3) 10 cm between corn and soybean, with three replicates under randomized block design. Results: Findings depicted that height and number of corn stalks and ears were similar (P > 0.05) among different treatments. Numerically average corn ear height was decreased at zero cm distance. Dry matter percentage in all components; corn stalk, corn ear and soybean was also found not different (P > 0.05) but dry matter yield in component of corn ear was lower (P < 0.05) at zero cm distance as compared to that of 5 and 10 cm interrow distances. In case of nutritive value, total digestible nutrient yield in intercropped corn was also found lower (P < 0.05) at zero cm distance than that of 5 and 10 cm interrow distances between corn and soybean seeding rows. Substantial decrease in dry matter yield of maize ear at zero cm distance might be attributed to factor of closed interrow spacing which made interplant competition more intensified for light interception, necessary for photosynthetic activity. Lower dry matter yield in ear also reduced total digestible nutrients in intercropped maize because it was determining factor in calculation of digestible nutrients. The optimum yield and nutritive value of forage at wider interrow distance i.e. 5 cm between corn and soybean might be due to adequate interseed distance. Conclusion: Conclusively, pattern of corn and soybean seeding in rows at 5 cm distance was found suitable which provided adequate interrow distance to maintain enough mutual cooperation and decreased competition between both species for optimum production performance and nutritive value of intercropped forage.

• Journal of the Korean Geotechnical Society
• /
• v.34 no.12
• /
• pp.71-82
• /
• 2018

This study presents a reasonable and economical DCM reinforcement length for the various factors (the embankment height, the distance from the embankment to the underground structure, the depth of the soft ground, and the compression index and the swelling index of the soft ground) that affect the stability of the structure due to lateral movement. Based on these results, we analyzed each factor's degree of influence and figured out which factor influenced the lateral movement most. The cross section of the embankment on the soft ground was modeled by using the Finite Element Program and reinforced with DCM. The results show that the increase rate of the reinforcement length with the increase of the embankment height is about 9~50%, the increase rate of the reinforcement length with the depth of soft ground is about 13~30%, and the increase rate of the reinforcement length with increasing compression index is about 3~25%. In addition, the influence of each factor on each other was analyzed. As a result, among the separation distance, the compressive index and the maximum to minimum slope ratio of the reinforcement length of the embankment height, the separation distance was the largest for the depth of soft ground. As the depth of the soft ground increases, the ratio of the maximum to minimum slope of the reinforcement length according to the embankment height is 3.75, the ratio of the maximum to minimum slope of the reinforcement length according to the spacing distance is 4.3, and the ratio of maximum to minimum slope according to compression index is 2.5. From these results, it is confirmed that the three factors are greatly affected by the depth of soft ground.

• Korean Journal of Materials Research
• /
• v.25 no.9
• /
• pp.442-449
• /
• 2015

The effects of coating parameters were investigated in wear resistance coatings of Diamalloy-406 on Inconel 718 to obtain an optimum coating condition by high velocity oxy-fuel spraying. The coating parameters, the flow rates of source gases (hydrogen and oxygen), the powder feed rate, and the spray distance, were designed by the Taguchi method. The optimal conditions were determined: oxygen flow rate 34 FRM, hydrogen flow rate 57 FRM, powder feed rate 35 g/min, and spray distance 7 inch. Friction coefficients of the coating and the substrate decreased with an increasing sliding surface temperature from $25^{\circ}C$ to $450^{\circ}C$. The friction coefficient of Diamalloy-4006 coating decreased as the sliding surface temperature increased from $0.43{\pm}0.01$ at $25^{\circ}C$ to $0.29{\pm}0.01$ at $450^{\circ}C$. The wear trace and wear depth of the coating were smaller than the substrate at all temperatures tested. The relationship between spray parameters and wear resistance was discussed extensively, based on the measured roughness, hardness, and porosity in each coating.

• Journal of the Korean Geotechnical Society
• /
• v.18 no.3
• /
• pp.33-41
• /
• 2002

Soil nailing type of retaining structures has been widely used in Korea far the purpose of the temporary and permanent support in excavations and slope stability. The important factors in application of soil nailing systems in urban excavation site nearby the existing structures are the displacement of the wall and tensile farce of the nails, etc. In this paper, the fled back analyses are carried out at 11 excavation sites to investigate the behavior of tensile farce of nails at stepwise excavation in the multi-layered strata including various rock layers. The results of the fled back analysis are less than about 50% of the measured ones. The distance of active zone by measurements are shown almost larger than that of fled back analysis when the distance of active Bone is defined from the surface of wall to the potential failure surface. And the results of fled back analysis are within the range proposed by the project CLOUTERRE and Cartier & Gigan (1983) which were 0.3$H_f$, and 0.5$H_f$, of the final excavation depth ($H_f$,) respectively, but the values of the measurement were larger than these values.

• Journal of Animal Science and Technology
• /
• v.54 no.1
• /
• pp.51-58
• /
• 2012

The purposes of the study were to examine the changes in carcass traits and surface meat color, and cortisol concentration by different altitudes and shipping distances for steer and cow. The experimental animals were shipped from Kangwondo, Kyunggido, Choongchungdo, and Kyungsangdo to Wonju LPC. The animals were examined for yield traits, quality traits, carcass grade, lightness, redness, yellowness, croma value, and cortisol concentration by different altitudes and shipping distances. The results showed that the carcass traits of steer like back fat thickness were not different by shipping distances of 100 km, 150 km, and 200 km. However, the fat thickness was higher in steers shipped from 250 km than 100 km, 150 km, and 200 km distance. Ribeye area was reduced significantly in 200 km and 250 km than 50 km. Yield index and yield grade were significantly low in 250 km than 50-200 km. However, meat color, fat color, texture, mature, and quality grade had no differences between shipping distances. Marbling score was not different in 50-200 km. However, the marbling score in 250 km was significantly lower than that of 50 km. In case of surface meat color by shipping distance, redness, yellowness, chroma value, and hue-angle were not different in shipping distance of 250 km. The lightness had similar result in 50-200 km. However, in case of 250 km the lightness was significantly low. The REA of cow carcass by shipping distance had no differences by shipping distance. The BET had similar results in 50-150 km. However, it had significantly thick in 200 km. The yield index and yield grade had no differences in 50-150 km. However, yield index and grade were significantly low in 200 km. The carcass trait of cow had no differences in all items by shipping distance. Although the carcass traits and the BET for steer by altitude had no differences between 100, 200, 300 and 500 m, but those were significantly thick in 400 m. And the yield index and the yield grade at altitude 400 m were lower than that of other altitudes. The quality traits and the quality grade had no differences between 100, 200, 300, 400, and 500 m altitudes. The yield traits, quality traits, yield grade, and quality grade had no significant differences by altitudes. In case of yield index of cow for 300 m was low than the cases of 100 m and 200 m. The surface meat color for steer and cow had no differences by altitudes. However, the lightness of cow had positive result in 100 m than 200 m and 300 m. In case of steer and cow the cortisol concentration by shipping distance was high as the shipping distances were longer. However, the cortisol concentrations of steer and cow by altitudes were decreased as the altitudes were increased. From the above results carcass traits and carcass grade were decreased and the cortisol concentration was increased as the altitudes were decreased for steer and cow.

• Journal of Welding and Joining
• /
• v.15 no.1
• /
• pp.116-124
• /
• 1997

A scope of this study is to establish the optimum plasma spray conditions for fine ($5\mu\textrm{m}$) $Al_2O_3$ powder. However, the flowability of the $Al_2O_3$ powder is not so good because of irregular particle shape and fine particle size. Therefore, powder feeding system was modified by 1) change of powder feeding line material from polymer to copper 2) shorten the powder feeding tube length 3) heating the powder feeding system to $80^{\circ}C$4) vibrating the powder feeding line continuously, in order to feed the fine powder homogeneously. The homogeneous powder feeding conditions were obtained with the modified powder feeding system by controlling the powder carrier gas flow and the powder flow rate indicator. The best plasma spraying conditions for the fine $Al_2O_3$ powder were found out as 40kw gun power, 80 g/min. powder feed rate and 50 mm working distance after characterizing the microstructure, hardness and wear loss of the $Al_2O_3$ coating layer.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.2
• /
• pp.235-243
• /
• 1997

The high-$T_c$ superconducting phase, $YBa_2Cu_3O_x$, was deposited on the single crystal MgO substrate, using a liquid aerosol feed method in a plasma enhanced chemical vapor deposition(PECVD) reactor. The effect of the plasma distribution depending on the design of a reactor was studied by the analysis of the microstructures of thin films. The particles landed were frequently observed on the films and the two causes that were responsible for the particle deposition were explained. The particles were deposited by the unstable and non-uniform plasma and the low evaporation rate of the precursors. Also, the thin film deposition rate decreased significantly as the distance between the evaporating location and the substrate increased.