• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2000년도 봄 학술발표회논문집
• /
• pp.365-370
• /
• 2000

A sliding mode fuzzy control (SMFC) algorithm is applied to design a controller for a benchmark problem on a wind- excited building. The structure is a 76-story concrete office tower with a height of 306 meters, hence the wind resistance characteristics are very important for the serviceability as well as the safety. A control system with an active tuned mass damper is assumed to be installed on the top floor. Since the structural acceleration is measured only at ,limited number of locations without measurement of the wind force, the structure of the conventional continuous sliding mode control may have the feed-back loop only. So, an adaptive least mean squares (LMS) filter is employed in the SMFC algorithm to generate a fictitious feed-forward loop. The adaptive LMS filter is designed based on the information of the stochastic characteristics of the wind velocity along the structure. A numerical study is carried out. and the performance of the present SMFC with the ,adaptive LMS filter is investigated in comparison with those of' other control, of algorithms such as linear quadratic Gaussian control, frequency domain optimal control, quadratic stability control, continuous sliding mode control, and H/sub ∞///sub μ/, control, which were reported by other researchers. The effectiveness of the adaptive LMS filter is also examined. The results indicate that the present algorithm is very efficient .

• Journal of Electrical Engineering and Technology
• /
• 제12권6호
• /
• pp.2227-2236
• /
• 2017

In order to solve the neutral-point voltage fluctuation problem of three-phase three-level T-type inverters (TPTLTIs), the unbalance characteristics of capacitor voltages under different switching states and the mechanism of neutral-point voltage fluctuation are revealed. Based on the mathematical model of a TPTLTI, a feed-forward voltage balancing control strategy of DC-link capacitor voltages error is proposed. The strategy generates a DC bias voltage using a capacitor voltage loop with a proportional integral (PI) controller. The proposed strategy can suppress the neutral-point voltage fluctuation effectively and improve the quality of output currents. The correctness of the theoretical analysis is verified through simulations. An experimental prototype of a TPTLTI based on Digital Signal Processor (DSP) is built. The feasibility and effectiveness of the proposed strategy is verified through experiment. The results from simulations and experiment match very well.

• 한국자기학회지
• /
• 제22권2호
• /
• pp.45-48
• /
• 2012

Co계 비정질 리본인 Metglass$^{(R)}$2714A 코어를 사용하여, 자기장 측정 범위가 ${\pm}100\;{\mu}T$, 측정 주파수 범위가 dc~10 Hz인 3-축의 피드백형 플럭스게이트 마그네토미터를 제작하였다. 제작된 마그네토미터의 아날로그 출력의 전기잡음은 5 pT/$\sqrt{Hz}$ at 1 Hz 이었으며, Micro-controller와 24 bit ADC(Analog to Digital Converter)를 사용한 마그네토미터의 출력을 0.1 nT의 분해능으로 디지털로 출력 할 수 있게 하였다. 디지털 신호로 출력되는 마그네토미터의 선형도는 $1{\times}10^{-4}$ 이하였으며, 1시간 동안 영점 변화는 0.2 nT 이하였다.

• 대한기계학회논문집A
• /
• 제25권8호
• /
• pp.1173-1182
• /
• 2001

Recent noticeable advances of CNC machine tools have considerably improved productivity and precision in manufacturing processes. However, in the respect of productivity some defects still remain because selection of machining conditions entirely depends on the experiences of programmers. Usually, machining conditions such as feed rate and spindle speed have been selected conservatively by considering the worst cases, and it has brought the loss of machining efficiency. Thus, the improvement of cutting force controller has been done to regulate cutting force constantly and to maximize feedrate simultaneously in case that machining conditions change variously. In this study, sliding mode control with boundary layer is applied to milling process for cutting force regulation and in a commercial CNC machining center data transfer between PC and PMC (programmable machine controller) of CNC machine is done using a standard interface method. And in the cutting force measurement, an indirect cutting force measuring system using current signal of AC servo is adopted in order not to use high-priced equipment like tool dynamometer. The purpose of this study is to maximize the productivity in milling process, thus its results can be applied to cases such as rough cutting process.

• 제어로봇시스템학회논문지
• /
• 제22권5호
• /
• pp.320-325
• /
• 2016

This paper presents a robust finite-time sliding mode control (SMC) scheme for unknown disturbance and unmodeled nonlinear friction and dynamics in the robotic manipulator. A finite-time SMC (FSMC) surface and finite-time sliding mode controller are constructed to obtain faster error convergence than the conventional infinite-time based SMC. By adding prescribed constraint control term to a finite-time SMC to compensate for unknown disturbance and uncertainties, a robust control scheme can be designed as well as faster convergence control. In addition, simpler controller structure is built by using feed-forwarding upper bound coefficients of each manipulator dynamic parameters instead of model-based control or adaptive observer to estimate unknown manipulator parameters. Simulation and experimental evaluations highlight the efficacy of the proposed control scheme for an articulated robotic manipulator.

• Journal of Power Electronics
• /
• 제13권5호
• /
• pp.798-805
• /
• 2013

This paper presents the control and implementation of the dual-stator-winding induction generator for variable frequency AC (VFAC) generating system. This generator has two sets of stator windings embedded into the stator slots. The power winding produces the VFAC power to feed the loads, and the control winding is connected to the static excitation controller to control the generator for output voltage regulation with speed and load variations. On the basis of the idea of power balance, an instantaneous slip frequency control (ISFC) strategy using the information of both the output voltage and the output power is used in this system. A series of experiments is carried out on a 15 kW prototype for verification. Results show that the system has good static and dynamic performance in a wide speed range, which demonstrates that the ISFC strategy is suitable for this system.

• 대한기계학회논문집A
• /
• 제28권7호
• /
• pp.1029-1037
• /
• 2004

High-speed/precision servomechanisms have been widely used in the manufacturing and semiconductor industries. In order to ensure the required high-speed and high-precision specifications in servomechanisms, an integrated design methodology is required, where the interactions between mechanical and electrical subsystems will have to be considered simultaneously. For the first step of the integrated design process, it is necessary to obtain not only strict mathematical models of separate subsystems but also formulation of an integrated design problem. A two-degree-of-freedom controller described in the discrete-time domain is considered as an electrical subsystem in this paper. An accurate identification process of the mechanical subsystem is conducted to verify the obtained mathematical model. Mechanical and electrical constraints render the integrated design problem accurate. Analysis of the system performance according to design and operating parameters is conducted for better understanding of the dynamic behavior and interactions of the servomechanism. Experiments are performed to verify the validity of the integrated design problem in the x-Y positioning system.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.1019-1022
• /
• 2002

Pipe-cutting machines have been used in many fields. Recently, an automatic pipe-cutting machine that uses magnet has born developed. In this paper, a magnetic-type automatic pipe-cutting machine that attaches itself and performs unmanned cutting process is proposed. It is designed that there is a room at the bottom of its body to contain a magnet. And it uses magnetic force between the magnet and the pipe surface to prevent slip and to attach the machine to the pipe against gravity. Also the magnetic force is adjustable by changing the gap between the magnet and the pipe. This machine is, however, necessary to control cutting velocity for the elevation of work efficiency and the adjustable faculties. During pipe cutting process, the gravity acting on the pipe-cutting machine widely varies. That is, the cutting machine gets fast when moving from the top to the bottom of the pipe and slow when moving from the bottom to the top. Actually the system is kind of a non-linear system where the gravity is function of climbing angle of the cutting machine along the pipe. Especially jerking motion is critical. Therefore, authors design the non-linear controller that estimates the current position of the machine along the pipe and compensates the effect of gravity in this paper. It receives the feed back signal from the encoder.

• 한국정밀공학회지
• /
• 제26권12호
• /
• pp.55-61
• /
• 2009

Machining systems have been evolved to produce more detailed products of high added value. This has been possible, in large part, due to the development of highly accurate multi-axis CNC machine tools. The conventional CNC of machine tools has individual axis controllers to maximize tracking performance. On the other hand, cross-coupling controllers can be integrated into the conventional CNC to enhance contouring performance. For this multi-axis cross-coupling control system, it is necessary to automatically adjust the controller gains depending on operating conditions and/or other external conditions from an optimization perspective. This paper proposes automatic modeling of feed drive systems that minimizes the difference in behavior between the system model and the actual system. Based on the modeling, an integrated auto-tuning method is also proposed to improve both tracking and contouring accuracy of a 3-axis cross-coupling control system as well as users' convenience. The proposed methods are evaluated by both simulation and experiments.

• 대한기계학회논문집
• /
• 제16권1호
• /
• pp.156-161
• /
• 1992

본 연구에서는 이송축 직류 서보 모터의 전류신호와 NC정보를 이용해서 선삭 가공상태를 감시하는 시스템을 개발하였다. 모터 전류는 가공 부하의 상태를 잘 나 타내며, NC 장치에 내장되어 있기 때문에 신호 검출을 위한 별도의 센서가 필요 없어 서 공구가 수시로 바뀌는 NC작업 감시를 위한 유효한 신호이다. 또 NC 정보로부터 작업을 예측함으로써 감시 대상을 명확히 하고 신뢰성을 높이고자 하였다. 전체적인 감시 시스템의 프로그래밍 언어로는 C를 사용하여, 실시간 감시처리를 가능하게 하였 다.