• Textile Coloration and Finishing
• /
• v.20 no.6
• /
• pp.42-50
• /
• 2008

The objective of this study is to investigate the efficacy of pomegranate hull colorant as a natural hair coloring dye. The extract of pomegranate hull was concentrated and freeze-dried to get colorant powder. Effect of dyeing condition and mordanting on the dye uptake of hair by using Al, Fe, Cu, Cr, Sn compounds, color change and colorfastness were explored. In addition, tensile strength was measured and the surface of the hair was observed. Dye uptake of hair measured by K/S value (400 nm) indicated that ionic bonding seems to be involved in the sorption of pomegranate colorant to hair. Maximum sorption was obtained at pH 3.5 and the concentration of 50% (on the weight of hair, o.w.h.). Acidic dyeing condition (pH $3.5{\sim}5.0$) showed yellow color however alkaline dyeing condition (pH $7{\sim}11$) gave reddish yellow color. Pomegranate hull colorant produced greyish brown color on hair and the hair mordanted with Fe showed dark brown color. Mordants except Fe did not increase dye uptake significantly. Mordants except Cu increased light fastness and mordants except Cr increased washing fastness level slightly. According to SEM observation and the tensile strength retention measurement, the mordant dyed hair gave more damage to hair by ultraviolet light and washing than the hair dyed without mordanting. Experimental results of K/S value and colorfastness(light and washing) supported that pomegranate hull colorant without mordanting can be used as a semi-permanent natural hair coloring dye.

• Ocean and Polar Research
• /
• v.26 no.2
• /
• pp.121-132
• /
• 2004

Concentrations of Al, As, Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb, Zn were determined in four arctic brown algae (Laminaria saccharina, L. digitata, Alaria esculenta, Desmarestia aculeata) in an attempt to examine for their metal accumulation capacity and also to assess their contamination levels. Macroalgae were collected from shallow subtidal waters (<20m) of Kongsfjorden (Kings Bay) on Spitsbergen during the period of the late July to early August 2003. Metal concentrations highly varied between sampling sites, species and tissue parts. Input of melt-water laden with terrigenous sediment particles seemed to have a large influence on baseline accumulations of some metals (Al, Fe, Mn, Pb etc.) in the macroalgae, causing a significant spatial variation. There were also significant concentration differences between the young and old tissue parts in L. saccharina, L. digitata and A. esculenta. While Al, Fe, Mn, Pb were higher in the perennial parts (stipes and holdfast below meristematic region), Cd and As concentrations were significantly higher in the young blades above the meristematic region. Zn and Cr, on the other hand, showed little differences between the tissue parts. The highest metal concentrations were found in D. aculeata, which seems to be due to its filamentous fine branches leading to high surface/volume ratios. The lowest concentrations were found in the two Laminaria spp., the blades of which are thicker than D. aculeata and A. esculenta. No distinct signs of contamination were detected in the brown algal species analyzed. Added to this, the results of the present studies suggest the potential utility of L. saccharina, L. digitata and A. esculenta as biomonitors for metal pollution monitoring in this area.

• The Korean Journal of Food And Nutrition
• /
• v.27 no.4
• /
• pp.570-580
• /
• 2014

The purpose of this study was to investigate the effect of calcium (Ca) and vitamin D (vit. D) levels on metabolism of various minerals such as Ca, P, Mg, Fe, Zn, Cu, and Cr. The comparison was made on the rats that were placed on diet containing powdered skim milk with different Ca and vit. D levels for 5 weeks. A total of 42 5-week-old Sprague-Dawley rats were divided into 7 groups as follows: Control group consisted of normal Ca and normal vit. D (0.5% Ca, 1,000 IU vit. D); Experimental groups were divided into low (0.25%) and high (1.0%) calcium levels; and vit. D group was divided into low (10 IU), normal (1,000 IU), and high (5,000 IU) subgroups. The weight gain and food efficiency ratios of the rats were not significantly different with increasing dietary Ca levels. The absorption rates of 7 minerals (Ca, P, Mg, Fe, Zn, Cu, and Cr) were significantly decreased with increasing dietary Ca levels. Also, fecal excretion of P significantly increased with increasing dietary vit. D levels (p<0.05), and urine excretion of Fe was significantly increased with increasing dietary vit. D levels (p<0.001). The result indicated that higher Ca intake affected on bioavailability of other minerals, due to interactions among minerals in the process of intestinal absorption. However, vitamin D intake had no effect on bioavailability of several minerals. Therefore, it could be suggested that adequate Ca intake is important for balance of the minerals.

• Journal of environmental and Sanitary engineering
• /
• v.9 no.2
• /
• pp.8-23
• /
• 1994

During the period from Mar., 1991 to Feb., 1992 66 tSP samples were collected by Hi volume air sampler at 1 sampling site in Seoul and the amount of concentration of 21 components(SO$_{4}$$^{2-}$, NO$_{3}$$^{-}$, NH$_{4}$$^{+}$, Cl$^{-}$, Al, Ba, Ca, Cd, Cr, Cu, Fe, It Mg, Mn, Na, Ni, Pt Si, Ti, Zn, Zr ) were measured. And monthly and seasonal variation were surveyed and the principal component analysis( PCA ) were carried out with respect to these amount of pollutants, minimum of visibility and radiation on a horizontal surface. The total amount of soluble ion in water was high in order o(SO$_{4}$$^{2-}$> NO$_{3}$$^{-}$> N%'>Cl$^{-}$ and metal ion was high in order of Na> Ca>Si> Fe> Al> K> Mg> Zn> Pb> Cu>Ti> Mn > Ba> Cr> Zr> Ni> Cd. There was Seasonal variation in concentration for SO$_{4}$$^{2-}$, NH$_{4}$$^{+}$, Cl$^{-}$, Na, Al, Ca, Bt Mg, Fe and Si. It was assumed that the components of the highest concentration on April were depend on yellow sand and the frequency of wind velocity and direction. As the results of PCA, the amount of pollution components was able to characterized with two principal components(Z$_{1}$, Z$_{2}$ ). The first principal components Z$_{1}$ was considered to be a factor indicating the pollutants originated from natural generation and The second principal components Z$_{2}$ was considered to be a factor indicating the pollutants originated from human work. The monthly concentration of pollutants in ISP, minimum of visibility and radiation on a horizontal surface was possible to evaluate by the use of these two principal components Z$_{1}$ and Z$_{2}$ .

• Journal of Powder Materials
• /
• v.20 no.6
• /
• pp.432-438
• /
• 2013

In this study, analysis on the oxidation behavior was conducted by a series of high-temperature oxidation tests at both $800^{\circ}C$, $900^{\circ}C$ and 1000 in the air with sintered STS 316L. The weight gain of each oxidized specimen was measured, the oxidized surface morphologies and composition of oxidation layer were analyzed with Scanning Electron Microscope-Energy Dispersive x-ray Spectroscopy (SEM-EDS), finally, the phase change and composition of the oxidized specimen were shown by X-Ray Diffraction (XRD). As a result, the weight gain increased sharply at $1000^{\circ}C$ when oxidation test was conducted for 210 hours. Also, a plentiful of pores were observed in the surface oxidation layers at $900^{\circ}C$ for 210 hours. In addition, the following conclusions on oxidation behavior of sintered STS 316L can be obtained: $Cr_2O_3$ can be formed on pores by influxing oxygen through open-pores, $(Fe_{0.6}Cr_{0.4})_2O_3$ can be generated on the inner oxidation layer, and $Fe_2O_3$ was on the outer oxidation layer. Also, $NiFe_2O_4$ could be precipitated if the oxidation time was kept longer.

• Journal of the Korean earth science society
• /
• v.26 no.8
• /
• pp.800-808
• /
• 2005

Elemental mobility during the weathering of granite in the Gwangju Hyangdeung area was investigated using ICP-MS analysis. It appeared that Al, Fe, Ti, K were lost from the profile, whereas Si, Ca, Na Mg, P and Mn were immobile during chemical weathering. In less weathered soil, large enrichment of K and Ti were found relative to Al, whereas other elements such as Si, Ca, Na, Mg and P are deplete. Fe content is constant throughout the weathered profiles. Amounts of Rb, Sr, Y, Cs, Pb, Th and U increased toward the surface. Nb, and Co have accumulated in the deepest parts of the weathered soil profile. These results agree with similar published studies. In addition, the analytical data shows that Ba and Ga increased, while Cu, Zn, Cr and Ni were relatively constant in this area. REE tend to increase in most samples, while LREEs, relative to Al, were enriched in the lower and upper saprolite. HREEs were enriched in the lower and upper saprolite.

• Korean Journal of Metals and Materials
• /
• v.50 no.2
• /
• pp.107-115
• /
• 2012

Direct laser melting (DLM) is a powder-based additive manufacturing process to produce parts by layer-by-layer laser melting. As the properties of the manufactured parts depend strongly on the deposited laser-melted bead, deposited layers obtained by the DLM process were characterized in this study. This investigation used a 200 W fiber laser to produce single-line beads under a variety of different energy distributions. In order to obtain a feasible range for the two main process parameters (i.e. laser power and scan rate), bead shapes of single track deposition were intensively investigated. The effects of the processing parameters, such as powder layer thickness and scan spacing, on geometries of the deposited layers have also been analyzed. As a result, minimum energy criteria that can achieve a complete melting have been suggested at the given powder layer thickness. The surface roughnesses of the deposited beads were strongly dependent on the overlap ratio of adjacent beads and on the energy distributions of laser power. Through microstructural analysis and hardness measurement, the morphological and mechanical properties of the deposited layers at various overlapped beads have also been characterized.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.20 no.1
• /
• pp.49-55
• /
• 2024

Stainless 630 (or 17-4PH) is a precipitation-hardening martensitic stainless steel that has excellent mechanical properties and corrosion resistance. These characteristics make the STS630 to be used as a consisting material for various components such as spider, pin, spring, and spring retainer, of the control rod drive mechanism (CRDM) in pressurized water reactors (PWRs). In general, it is well known that the oxide layer of stainless steel consists of a duplex layer, a compact inner layer of FeCr₂O₄ spinel, and a coarse-grained outer layer of Fe₃O₄ spinel in PWR primary coolant condition. However, the characteristics of the oxide layer can be sensitively influenced by various water chemistry conditions such as temperature, dissolved oxygen, dissolved hydrogen, pH, pH adjuster type, and exposure time. In this work, we investigate the corrosion properties of the STS630 as a function of coolant temperature in an NH3 alkaline solution for its boron-free application in a small modular reactor, to confirm the feasibility for usage as a boron-free SMR structural material. As a result, oxide layer of corroded STS630 is consist of double-layer oxides consisting of a Cr-rich dense inner oxide and a Fe-rich polyhedral outer particles like as that in commercial PWR primary coolant. The corrosion rate of STS630 increases with increase in test time and temperature and the corrosion rate-time model equation was developed based on experimental data. Overall, it is expected that the results in this study provides useful data for the corrosion behavior of STS630 in alkaline environments, contributing to the development of selecting suitable materials for SMRs.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.135-135
• /
• 2018

천이금속 질화물 코팅은 우수한 기계적 특성들로 인해 공구 코팅으로 많이 사용 되어왔다. 그 중에서도 특히 Cr계 경질 코팅은 높은 경도와 낮은 표면조도, 우수한 마찰특성 등 뛰어난 기계적 특성을 나타내므로 공구 코팅으로의 적용 가능성이 크다. 그러나 최근 공구산업의 발전으로 인해 공구가 더욱 가혹한 환경에서 사용됨에 따라, 공구의 수명을 향상시키고 보호하기 위해 코팅의 높은 밀착력이 요구되고 있으며, 모재와 코팅 사이에 중간층을 합성함으로써 공구의 밀착력을 향상시키는 연구가 활발히 진행되고 있다. 이전 연구에서 모재/중간층/코팅간의 경도와 탄성계수 비율(H/E ratio)의 구배가 코팅의 밀착력에 큰 영향을 미치는 것으로 확인되었다. 그러므로, WC 모재와 Cr계 코팅의 중간값의 H/E ratio를 갖는 중간층의 합성을 통해 코팅의 밀착력을 향상시킬 수 있을 것으로 판단된다. 본 연구에서는, 코팅의 밀착력을 향상시키기 위해 다양한 중간층을 증착한 CrZrN, CrAlN 코팅을 비대칭 마그네트론 스퍼터링 장비를 이용하여 합성하였다. 모재로는 디스크 형상의 WC-6wt.%Co 시편을 사용하였고 Cr, Zr, Si, Al single 타겟을 이용하여 Cr, CrN, CrZrN, CrZrSiN 등의 중간층이 증착된 코팅을 합성했다. 코팅의 합금상, 경도 및 탄성계수, 미세조직 및 조성, 표면 조도을 확인하기 위해 X-ray diffractometer (XRD), Fischer scope, field-emission scanning electron microscopy (FE-SEM), energy dispersive X-ray spectroscopy (EDS), atomic force microscopy를 사용하였고, 코팅의 밀착 특성을 분석하기 위해 scratch tester와 optical microscopy (OM)를 이용하였다. 코팅의 내열성을 확인하기 위해 코팅을 furnace에 넣어 공기중에서 500, 600, 700, 800, 900, $1,000^{\circ}C$로 30분 동안 annealing 한 후에 nano-indentation을 사용하여 경도를 측정하였다. CrZrN 및 CrAlN 코팅을 나노 인덴테이션으로 분석한 결과, 모든 코팅의 경도(33.4-35.8 GPa)와 탄성계수(384.1-391.4 GPa)는 중간층의 종류에 상관없이 비슷한 값을 보인 것으로 확인됐다. 그러나, 코팅의 마찰계수는 중간층의 종류에 따라 다른 값을 보였다. CrZrN 코팅의 경우 CrN 합금상 중간층을 갖을 때 가장 낮은 값을 보였으며, CrAlN 코팅의 경우 CrN/CrZrSiN 중간층을 증착하였을때 마찰계수는 0.34로 CrZrN 중간층을 증착하였을 때(0.41)에 비해 낮은 값을 보였다. 또한, 코팅의 마모율 및 마모폭도 비슷한 경향을 보인 것으로 보아, CrN/CrZrSiN 중간층을 합성한 CrAlN 코팅의 내마모성이 상대적으로 우수한 것으로 판단된다. 코팅의 밀착력의 경우도 마찰계수와 비슷한 경향을 보였다. 이것은 중간층의 H/E ratio가 코팅의 내마모성에 미치는 영향에 의한 결과로 사료된다. H/E ratio는 파단시의 최대 탄성 변형율로써, 모재/중간층/코팅의 H/E ratio 구배에 따라 코팅 내의 응력의 완화 정도가 변하게 된다. WC 모재 (H/E=0.040)와 CrAlN 코팅(H/E=0.089) 사이에서 CrN, CrZrSiN 중간층의 H/E ratio는 각각 0.076, 0.083으로 모재/중간층/코팅의 H/E ratio 구배가 점차 증가함을 확인 할 수 있었고, 일정 응력이 지속적으로 가해지면서 진행되는 마모시험중에 CrN과 CrZrSiN 중간층이 WC와 CrAlN 코팅 사이에서 코팅 내부의 응력구배를 완화시키는 역할을 함으로써 CrAlN 코팅의 내마모성이 향상된 것으로 판단된다. 모든 코팅을 열처리 후 경도 분석 결과, CrN/CrZrSiN 중간층을 증착한 CrAlN 코팅은 $1,000^{\circ}C$까지 약 28GPa의 높은 경도를 유지한 것으로 확인 되었고, 이는 CrZrSiN 중간층 내에 존재하는 SiNx 비정질상의 우수한 내산화성에 의한 결과로 판단된다.

• Composites Research
• /
• v.34 no.5
• /
• pp.311-316
• /
• 2021

In this study, TiC/steel metal matrix composites were fabricated by powder metallurgy process using Fealloy powders with 3 wt.% Cr and 10 wt.% Cr, respectively, as matrix material. Subsequently, the composite samples were heat treated by the annealing and quenching-tempering(Q-T), respectively, to understand the effect of heat treatment on the mechanical properties of the composites. The correlation between microstructure and structural strength depending on the chromium content and the heat treatment conditions was studied through tensile, compressive, and transverse rupture test and microstructural analysis. In the case of TiC/steel composite containing 10 wt.% Cr, the tensile strength and transverse rupture strength at room temperature were significantly lowered by the influence of coarse chromium carbide formed at the TiC/steel interface. On the other hand, both TiC/steel composites containing 3 wt.% Cr and 10 wt.% Cr showed much higher compressive strength of about 4 GP after quenching-tempering compared to the annealed specimens regardless of the presence of the chromium carbide.