• Applied Microscopy
• /
• v.46 no.1
• /
• pp.45-50
• /
• 2016

Iron containing a high amount of chromium is known to be inferior to ductility due to ${\sigma}$ phase formation so that it is generally difficult to apply the plastic deformation process although the alloy possesses a superior characteristics of an excellent corrosion resistance. In this study, Fe-50mass%Cr alloy was melted using high purity powder and the deformation behavior has been investigated by cold rolling and tensile test. The tensile test yielded that the alloy revealed a serration at an early stage of tensile deformation and then the serrated flow vanished to change to a normal work hardening flow at the later stage. The former was governed by twin formation process, the latter by dislocation multiplication one, bringing about a high ductility of 20% or over. The reduction ratio in cold rolling was attained as high as 90%, thus the high corrosion-resistant alloy is able to possess a high ductility.

• Proceedings of the KIEE Conference
• /
• 2001.11b
• /
• pp.106-108
• /
• 2001

As 3V cathode material, a new doping spinel material, LiMn1.6Se0.4O4 powder with a phase-pure polycrystalline was synthesized by a sol-gel method. In spite of Jahn-teller distortion in 3V region($2.4{\sim}3.5V$), the LiMn1.6Se0.4O4 electrode shows no capacity loss. The material in the 3V region initially delivers a discharge capacity of 100mAh/g which increase with cycling to reach 105mAh/g after 90cycles. And 5V cathode material LiNi0.5-xMxMn1.5O4(M=Cr, V, Fe) compounds have been synthesized by sol-gel method. a series of electroactive spinel compounds, LiNi0.5-xMxMn1.5O4(M=Cr, V, Fe) has been studied by crystallographic and electrochemical methods. The material presents only one plateau at around 4.5 V vs. Li/Li+ with a large discharge capacity of 152mAh/g and fairly good cyclability.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.395-401
• /
• 2008

Since metallic foam will increase the performance of heat exchanger, it have caused many researcher's attention recently. Our research base on the model that metallic foams applied to heat exchanger. In this case, there is three kind of heat transfer mechanisms, heat conduction in fibers, heat transfer by conduction in fluid phase, and internal heat change between solid and fluid phases. In this paper we study both the hydraulic and thermal aspect performance. Pressure drop along air flow direction will be presented. As thermal aspect, we first discuss the acceptance of applying thermal equilibrium among the two phases. then to calculate the dimensionless temperature profile, the heat transfer coefficient and Nu number in 14 metallic foams(7 Aluminium foams, 7 FeCrAlY foams). All these discussion is based on the same velocity u=2 m/s.

• Corrosion Science and Technology
• /
• v.10 no.4
• /
• pp.118-124
• /
• 2011

Alloy 600 (Ni 75 wt%, Cr 15 wt%, Fe 10 wt%) as a heat exchanger tube of the steam generator (SG) in nuclear power plants (NPP) has been degraded by various corrosion mechanism during the long-term operation. Especially lead (Pb) is known to be one of the most deleterious species in the secondary system causing outer diameter stress corrosion cracking (ODSCC). Oxide formation and breakdown is requisite for SCC initiation and propagation. Therefore it is expected that a property change of the oxide formed on SG tubing materials by lead addition into a solution is closely related to PbSCC. In the present work, the SCC susceptibility was assessed by using a slow strain rate test (SSRT) in caustic solutions with and without lead for Alloy 600 and Alloy 690 (Ni 60 wt%, Cr 30 wt%, Fe 10 wt%) used as an alternative of Alloy 600 because of outstanding superiority to SCC. The results were discussed in view of the oxide property formed on Alloy 600 and Alloy 690. The oxides formed on Alloy 600 and Alloy 690 in aqueous solutions with and without lead were examined by using a transmission electron microscopy (TEM), equipped with an energy dispersive x-ray spectroscopy (EDXS).

• Corrosion Science and Technology
• /
• v.7 no.6
• /
• pp.301-306
• /
• 2008

Surface composite layers of 1.9~2.9 mm in thickness were fabricated by depositing metamorphic powders on a carbon steel substrate and by irradiating with a high-energy electron beam. In the surface composite layers, 48~64 vol.% of $Cr_{2}B$ or $Cr_{1.65}Fe_{0.35}B_{0.96}$ borides were densely precipitated in the austenite or martensite matrix. These hard borides improved the hardness of the surface composite layer. According to the otentiodynamic polarization test results of the surface composites, coatings, STS304 stainless steel, and carbon steel substrate, the corrosion potential of the surface composite fabricated with 'C+' powders was highest, and its corrosion current density was lowest, while its pitting potential was similar to that of the STS304 steel. This indicated that the overall corrosion resistance of the surface composite fabricated with 'C+' powders was the best among the tested materials. Austenite and martensite phases of the surface composites and coatings was selectively corroded, while borides were retained inside pits. In the coating fabricated with 'C+' powders, the localized corrosion additionally occurred along splat boundaries, and thus the corrosion resistance of the coating was worse than that of the surface composite.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.7
• /
• pp.681-686
• /
• 2009

Direct laser metal forming technology was applied to restore the damaged mold surface. In order to estimate melting characteristics of the $20{\mu}m$ Fe-Cr-Ni powder, single layer experiments were performed at various levels of heat input. The process window of the $20{\mu}m$ Fe-Cr-Ni powder provided feasible process parameters for the smooth regular surface. The cross hatching scanning strategy on the multiple layer experiment was performed to reduce the thickness non-uniformity of edge portions compared with the one direction scanning. To estimate the coherence between the melted powder and the basematal, the tendency of hardness distribution has been observed. The hardness of the melted and the remelted zone was distributed from 400HV to 600HV. It is over 2 times compared of the hardness of the basemetal. Experimental results show that the mold restoring process using direct laser metal forming can be successfully applied in the mold repair industry.

• Nuclear Engineering and Technology
• /
• v.40 no.2
• /
• pp.99-106
• /
• 2008

Through mechanical alloying, hot isostatic pressing and hot rolling, a 9%Cr Fe-based oxide dispersion-strengthened alloy sample was fabricated. The tensile strength of the alloy is significantly improved when the microstructure is modified during the post-consolidation process. The alloy samples were strengthened as the cooling rates increased, though the elongation was somewhat reduced. With a cooling rate of $800^{\circ}C/s$ after normalization at $1150^{\circ}C$, the alloy sample showed a tensile strength of 1450 MPa, which is about twice that of the hot rolled sample; however, at $600^{\circ}C$ the tensile strength dramatically decreased to 620 MPa. Optical microscope and transmission electron microscope were used to investigate the microstructural changes of the specimens. The resultant strengthening of the alloy sample could be mainly attributed to the interstitially dissolved nitrogen, the fraction of the tempered martensite, the fine grain and the presence of a smaller precipitate. The decrease in the tensile strength was mainly caused by the precipitation of vanadium-rich nitride.

• YAKHAK HOEJI
• /
• v.45 no.5
• /
• pp.460-467
• /
• 2001

Heavy metals, such as Al, As, Cd, Cr Cu, Fe, Hg, Mn, Mo, Ni, Pb, Se, Si, Sn, V and Zn, were analysed on kidney cortex and medulla of Korean obtained from 154 forensic medical autopsy cadavers. Heavy metals were analysed by inductively coupled plasma atomic emission spectrometry In kidney cortex, the concentrations of Al, Cd, Cu, Mn, Mo, Pb, Se, Si and Zn were significantly higher than in the kidney medulla (Cd, Cu, Mn, Mo, Zn : p<0.01, AA, Pb, Se, Si : p<0.05). No significant local differences were found between kidney cortex and kidney medulla in the concentrations of As, Cr Fe, Hg, Ni, Sn and V. In kidney cortex and kidney medulla, Cd concentrations correlated positively with age, but Mn concentrations correlated negatively with age. A significantly positive correlation between Cd and Zn, Cd and Cu, Zn and Cu, Al and Si, Se and As was found in kidney cortex and kidney medulla. A significantly positive correlation between Hg and Se was only observed in kidney cortex. These results indicate that the distribution of hazardous heavy metals is similar to that of essential elements in the tissues.

• Journal of Environmental Science International
• /
• v.2 no.1
• /
• pp.69-78
• /
• 1993

Contents of heavy metals (Cr, Cu, Zn, Cd, and Pb) in the sediments of Ulsan Bay were investigated by the sequential extraction methods that classifies heavy metals into five types of chemical forms: exchangeable, bound to carbonates, bound to Fe-Mn oxides, bound to organic matter and residual. The analyses were determined by using an ICP-MS. Total Cr concentrations in the sediments were in the range of 41.6-96.4, Cu 60.7-680, Zn 189-1954, Cd 33.1-83.4, and Pb 138-567 mg/kg. Results of sequential fractionation indicates that relatively high proportion ( ~44%) of Cu is associated with organic matter. A large proportion of Pb is associated with three types of chemical forms: Fe-Mn oxides, organic matter, and residual. There were significant correlation in concentrations between the exchangeable components and total organic carbons. The heavy metals In the residual phase cannot be easily released to the environment since these are bound to the crystal lattice. But, reducible and organic Phases con a significant amount of most heavy metals. Therefore, there is Potential dancer of a substantial amount of metals becoming chemically mobile with environmental changes.

• Journal of Environmental Health Sciences
• /
• v.37 no.3
• /
• pp.209-217
• /
• 2011

Objectives: In this study, the size distribution of airborne particulates ($PM_{10}$) was measured by using Cascade Impactors. The purpose of this study was to assess the size distribution of metal and ionic materials of $PM_{10}$. Methods: Samples were collected in the Kunsan industrial complex from April 2006 to January 2007. Results: The mass fraction of $PM_{10}$ had a bimodal distribution between 2.1-3.1 ${\mu}M$, and the average mass fraction of particles less than 2.1-3.1 ${\mu}M$ was 47%. Average concentrations of PM10 were 68.05 ${\mu}g/m^3$ and seasonal concentration 95.44 ${\mu}g/m^3$ for spring, 49.03 ${\mu}g/m^3$ for summer, 81.99 ${\mu}g/m^3$ for fall, 52.66 ${\mu}g/m^3$ for winter, respectively. Conclusions: Seasonal variations of $PM_{10}$ were significant for showing peak values in spring. The average concentrations of Cd, Cr, Pb, and Fe were 1.54, 4.51, 14.11, and 254.3 $ng/m^3$, respectively. The ratios of fine particles to total mass were 0.47 for $PM_{10}$, 0.45 for Cr, and 0.16 for Fe, 0.91 for Cd and 0.49 for Pb, respectively.