• Journal of Power System Engineering
• /
• v.14 no.1
• /
• pp.59-64
• /
• 2010

Ferritic stainless steel is currently increasingly used for automotive exhaust material. The material for exhaust manifold is used in the temperature range of 500∼$850^{\circ}C$. Therefore, high temperature characteristic is an important one that affects it's life span. It has been investigated the effect of alloying elements of Cr, Mo, Nb, Ti in the ferritic stainless steel for exhaust manifold on the high temperature tensile strength. There was a few difference in the tensile strength at $600^{\circ}C$ with the exception of low Cr steel, but the steels containing higher Cr, Mo or Nb elements showed significantly higher tensile strength at the temperature of $800^{\circ}C$. The precipitates of the specimens after heat treating at the test temperature were electrolytic extracted, and quantitatively analysed using by SEM-EDS and TEM. The alloying elements of Cr and Mo increased the tensile strength as a solid solution strengthener, and on the other hand Nb element enhanced the strength by forming the fine intermetallic compounds such as NbC or $Fe_2Nb$.

• Journal of the Korean institute of surface engineering
• /
• v.51 no.3
• /
• pp.149-156
• /
• 2018

The corrosion and strength degradation characteristics of 1.25Cr-0.5Mo steels were studied under $650^{\circ}C$ in $76%N_2+6%O_2+16%CO_2+2%SO_2$ gas condition up to 500 hrs. Corroded specimens were characterized by weight gain, scanning electron microscope(SEM), energy dispersive X-ray spectroscopy(EDS), and X-ray diffraction(XRD). The tensile test was conducted to evaluate the mechanical strength and fracture mode with corrosion at high temperature. As the results of the experiments, thick Fe-rich oxide layers over $200{\mu}m$ were formed on the surface within 500 hrs. The thick oxide layers are formed with reduction of the cross-sectional area of the specimens. Thus, the strength tended to decrease with reduction of the cross-sectional area.

• Journal of Power System Engineering
• /
• v.16 no.5
• /
• pp.76-82
• /
• 2012

Duplex stainless steels have the dual microstructure of austenite and ferrite phases. This steel exhibits generally a high corrosion resistance and higher mechanical strength compared with austenitic stainless steels. The steels used in the investigation have the chemical composition of Fe-22Cr-xNi-yMn-0.2N in which the contents of Ni and Mn were varied with maintaining the equal [Ni/Cr] equivalent. The fraction of ferrite phase was increased with the increase of annealing temperature. The impact factor of Mn element on the [Ni] equivalent was amended on the basis of the results of the investigation. 4Mn-2Ni alloy showed the highest pitting corrosion resistance. The fraction ratio, grain size and misorientation angle between grains were measured, and the correlation with pitting potential was investigated.

• Journal of ILASS-Korea
• /
• v.17 no.3
• /
• pp.128-133
• /
• 2012

The present study aims to examine the influence of flame spray distance on the thermal behavior of micro-metal particles and the morphological characteristics of $Ni_{20}Cr$ layers coated on the preheated SCM415 substrates by using the conventional flame spray system. Commercially available nickel-based $Ni_{20}Cr$ particles with a mean diameter of $45{\mu}m$ were used. In addition, CFD simulations using a commercial code (FLUENT ver. 6.3.26) were conducted to estimate temperature and velocity distributions of the continuous and discrete phases before impact on the substrate. From FE-SEM images of coated layers on the substrates, it was observed that as the spray distance decreased, the metal particle morphology showed splash-like patterns and such a short stretch shape, resulting from higher particle momentums and the impact of partially melted particles. Moreover, it was found that the spray distance should be considered as one of important parameters in controlling the porosity and the adhesion strength.

• Journal of Environmental Science International
• /
• v.26 no.7
• /
• pp.847-858
• /
• 2017

For 26 soil series distributed more than 1% among 63 soil series in Jeju Island, natural uncultivated soil samples were collected. For these soils, the chemical speciation of eight heavy metals (Cd, Cr, Cu, Mn, Ni, Pb, V, and Zn) was examined. Further, the Plant Bioavailability (PB) and Mobility Factor (MF) of these heavy metals were evaluated using Tessier's 5-step sequential extraction method (exchangeable, carbonate, reducible (bound to Fe/Mn oxides), oxidizable (bound to organic matter), and residual fraction). The main form present was residual fraction for Cd and Zn; residual and oxidizable fractions for Cr, Cu, Ni, and Pb; reducible fraction for Mn; and carbonate fraction for V. The average plant availability and average mobility factor were found to be V (57.37%) > Zn (12.49%) > Cd (11.76%) > Cu (11.19%) > Pb (9.37%) > Cr (9.09%) > Mn (3.13%) > Ni (2.63%), and Mn (61.04%) > V (59.94%) > Zn (31.54%) > Cd (17.65%) > Cr (15.66%) > Ni (13.89%) > Pb (13.80%) > Cu (13.53%), respectively.

• Corrosion Science and Technology
• /
• v.2 no.2
• /
• pp.82-87
• /
• 2003

Stress corrosion cracking of Alloy 600 and Alloy 690 has been studied with a C-ring specimen in 1%, 10% and 40% NaOH at $315^{\circ}C$. SCC test was performed at 200 mV above corrosion potential. Initial stress on the apex of C-ring specimen was varied from 300 MPa to 565 MPa. Materials were heat treated at various temperatures. SCC resistance of Ni-$_\chi$Cr-10Fe alloy increased as the Cr content of the alloy increased if the density of an intergranular carbide were comparable. SCC resistance of Alloy 600 increased in caustic solution as the product of coverage of an intergranular carbide in grain boundary, intergranular carbide thickness and Cr concentration at grain boundary increased. Low temperature mill annealed Alloy 600 with small grain size and without intergranular carbide was most susceptible to SCC. TT Alloy 690 was most resistant to SCC due to the high value of the product of coverage of an intergranular carbide in grain boundary, intergranular carbide thickness and Cr concentration at grain boundary. Dependency of SCC rate on stress and NaOH concentration was obtained.

• Journal of the Korean Chemical Society
• /
• v.33 no.1
• /
• pp.113-119
• /
• 1989

Chelating resins containing hydrazide or triethylenetetramine side chain were prepared using a commercial cation exchage resin, Diaion WK 11, and their nitrogen contents were determined by elemental analysis. The synthesized resin, and commercial chelating resins, (Diaion-CR 10 and-CR 20) were treated with various metal chelates of which metal contents were subsequently determined by chelatometry. Sectioned beads of the resin-metal chelates were also observed using electron microprobs X-ray analyzer. To examine the catalytic activity of the resin-metal chelates, they were applied to the oxidation of various hydroxy compounds and l-ascorbic acid, and found to be effective catalysts.

• Journal of the Korean institute of surface engineering
• /
• v.20 no.2
• /
• pp.49-59
• /
• 1987

The properties of $Cr_2O_3-Al_2O_3-SiO_2$ composite oxide coatings on steel surface were investigated. The results obtained were as follows: The microhardness of oxide coating layer increased with increasing heat-treatment temperature and $Cr_2O_3$ content in coating layer. The hardness showed the highest value (850Hv) treated at 700$^{\circ}C$ for $SiO_2:Al_2O_3:Cr_2O_3$=1:1:4. Increasing heat-treatment temperature, corrosion current density became lower and coating layer became denser. The corrosion current density showed the lowest value $(6.5{\times}10^{-5}\;Acm^2)$ treated at 750$^{\circ}C\;for\;SiO_2:Al_2O_3:Cr_2O_3$=1:1:3. These results were explained by protective layer which was formed during heat-treatment. The bonding between matrix and coating layer is expected to be made mechanically and chemically by the inter diffusion of Ni and Fe. The composite oxide coating was formed by softening of the binder with increasing heat-treatment temperature. The strengthening of coating layer is to be resulted from the dispersion of major oxide particles.

• Journal of Powder Materials
• /
• v.28 no.5
• /
• pp.375-380
• /
• 2021

In this study, we investigate the effect of the duration of mechanical alloying on the microstructures and mechanical properties of ODS ferritic/martensitic steel. The Fe(bal.)-10Cr-1Mo pre-alloyed powder and Y₂O₃ powder are mechanically alloyed for the different mechanical alloying duration (0 to 40 h) and then constantly fabricated using a uniaxial hot pressing process. Upon increasing the mechanical alloying time, the average powder diameter and crystallite size increased dramatically. In the initial stages within 5 h of mechanical alloying, inhomogeneous grain morphology is observed along with coarsened carbide and oxide distributions; thus, precipitate phases are temporarily observed between the two powders because of insufficient collision energy to get fragmented. After 40 h of the MA process, however, fine martensitic grains and uniformly distributed oxide particles are observed. This led to a favorable tensile strength and elongation at room temperature and 650℃.

• Proceedings of the Korea Technology Innovation Society Conference
• /
• 1998.05a
• /
• pp.8-8
• /
• 1998

한 국가의 경쟁력은 여러 가지 생산요소들의 질적·양적 우위에 의해 결정되나, 그 중에서도 특히 기술이 체화된 인적자원이 경쟁력 확보의 핵심요소임은 재론의 여지가 없다. 과거 우리나라 급성장의 주요 원동력이었던 우수하고 풍부한 인력이 이제 더 이상 우리 경쟁력의 원천이 되지 못하고 있다. 무한경쟁시대를 이끌어갈 창의력과 지도력을 갖춘 고급기술인력이 부족하고, 우수한 기술인력이 과학기술계를 회피하고 있으며, 산업현장에서 실제문제를 해결할 수 있는 실천적 전문기술과 숙련된 기능을 제대로 갖춘 인력을 배출하지 못하고 있다. 이러한 기숙인력 양성의 문제들을 해결하기 위한 방안의 하나로서 일반대학과 별도로 기술인력양성을 전문으로 하는 학위과정 설치의 필요성이 대두되었으며, 1996년 교육개혁의 일환으로 단설대학원제도와 전문학위제도가 시행되기 시작하였다. 그동안 여러 분야에서 단설대학원 설립이 추진되었으며, 일부에서 운영이 시작되고 있으나 과학기술분야에서는 극히 일부의 사례만이 있을 뿐이고 아직 본격적으로 설립운영되고 있다고 보기 어렵다. 본고는 외국 공공연구기관에서 시행되는 단설대학원의 사례들을 조사 분석함으로써 우리나라 과학기술계 출연연구기관에서의 바람직한 운영모델을 제시하고자한다. 일본의 총합연구대학원대학과 연계대학원제도, 중국 국가연구소들의 학위수여제도, 프랑스 국가연구소들의 석·박사과정, 독일 연구기관들의 박사과정 등을 소개하며, 이 들의 특징과 장단점들을 비교한다. 이어서 우리나라에서 현재 진행되고 있는 현황을 분석하고, 과학기술계 출연연구기관의 단설대학원 설립의 방향과 활성화를 위한 개선방안 등을 제시한다. 보고하였다2) 이 경우 보호피막으로서 NiO 와 $LiCrO_2$가 작용하는데, $LiCrO_2$가 용융탄산염 중에서 보다 안정한 것으로 부터, Cr의 첨가가 내식성에 기여하는 것으로 판단하였다. 다음 단계 로서 Fe/Cr재료에 용-융탄산염 중에서 안정한 산화물을 형성하는 Al의 첨가효과를 검토하였다. Al의 첨가는 더욱 내식성을 향상시키는 것이 발견되었고, 약 4wt%의 첨가로 충분한 내식성을 가지 는 것을 보고 하였다. 그러나 이러한 안정한 산화물에 의한 내식성 향상은 전기진도도의 희생을 바탕으로 한 것으로서, 다읍 단계로서 Ti산화물의 반도체적인 특성을 이용하고자 제 4의 원소로서 Ti첨가를 시도하였다. 그러나 Fe/Cr/AVTi재료가 뛰어난 내식성을 가지는 것은 관찰되었으나, 전도도 향상에는 기여하지 못하는 것이 보고되었다. 현재 MCFC는 실용화를 위한 고성능화의 하나로서 가압하에서의 운전을 시도하고 있다. 이 러한 가압하에서의 운전은 기전력의 향상 및 전극반응의 촉진 등으로 출력의 향상을 가져오나. 현재 문제로 되고 있는 Cathode극인 NiO의 용해/석출 현상을 가속화하는 결과를 초래해, 이에대 한 대책으로서 Li-K보다 NiO의 용해가 적은 Li-Na탄산염으로의 전환이 진행되고 있다. 이러한 배경으로부터 Uchida그룹에서 개발한 FeiCr/AVTi재료와 현재 분리판 재료로 사용증인 SUS 310, S SUS 316재료에 대해. 산화성 분위기의 5기압까지의 가압하에서, Li-K, Li-Na탄산염에 대하여 부 식거동을 검토한 결과, 가압하에서 내식성이 향상되는 것이