• Journal of the Korean institute of surface engineering
• /
• v.31 no.6
• /
• pp.334-344
• /
• 1998

Yew coating pmccss t.o form a surface layer ol CrN phasc on mild steel (A81 1020!, AlSI Hi3, 1Cr-0.5Mo steel (ASTM A213 and Nickrl-base superalloy (Inconel 718) was developed. Surlaces of various alloys t,n.ateii by chromizing for the formation ol Cr diffusion layer was subsequently trcaled by plasma nitriding in order t.o form the hard CrS coating layer on the surfaces. This duplex plasma surface tri-atments of chromizing and plasma nitriding have induced a lormation of a duplex-lrcated surfacr hyer of approximat~ls 70-80 $\mu\textrm{m}$thickncss with a iargcly improved microiiardnrss up to approxiniateW 1500Hv(50gf). The main cause for the lage improvment in the surface hardncss is altribilted to [.he fact that CrN and $Fe_xN$ phases are created successfully by ccliromizins and plasma nilriding treatment. High tenipera1,urc wear resislance of the duplex-treated mild steel and HI3 steels at $600^{\circ}C$ was examined. Comparing the duplex-treated specimens with the specimens treated only by chromizing, the rcsults shovmi that, thc wear volume of the duplex-treated mild skcl and 1113 stcel aSt.er a wear test, at $600^{\circ}C$ were reduced hy a Iactor of 8 and 3, respectively. Characteristics of the CrS phase by duplrx treatment were compared with $CrN_x$,/TEX> film by ion plating and the wear behaviors of CrN film lormed by two different nroccsses arc nea.riy identical.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.94-94
• /
• 2013

The Cr-Zr-N films have much improved mechanical properties and very smooth surface roughness. However, in spite of their outstanding properties, the Cr-Zr-N coatings revealed their mechanical properties deteriorated severely with increasing Zr content at $500^{\circ}C$ ecause of very rapid oxidation. Recently oxynitride films have been widely studied due to their excellent unique mechanical properties and oxidation resistance. In this work, CrZr-O-N films with various O contents were synthesized by unbalanced magnetron sputtering with Cr-Zr segment targets (Cr:Zr volume ratios is 1：1) and all films were prepared in a nitrogen rich mixture of N2 and O2. Characteristics such as crystalline structure, hardness and chemical composition as a function of the O content were investigated by X-ray diffraction (XRD), field emission scanning electron microscope (FE-SEM), microhardness testing system and energy dispersive spectroscopy (EDS). Results showed that the thin films had dense and compact microstructure as O content in the films increases. The microstructure of the thin films consisted of mainly crystalline Cr (Zr)N phase and Cr2O3 phase. The maximum hardness and elastic modulus of the films was measured to be approximately 33.2 GPa and 280.6 GPa from the films with low content of O elements. Detailed experimental results will be presented.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.566-566
• /
• 2013

종래의 흑연 위주 연료전지 분리판에서 최근 고분자 전해질 막 연료전지가 높은 전력, 낮은 작동 온도로 자동차 산업에서 상당한 주목을 받고 있다. 분리판의 기술적 요구사항은 높은 전기 전도도, 높은 내식성, 가스 밀봉성, 경량성, 가공성, 저비용 등이다. 후보 물질로는 전기 전도성을 갖는 질화물계가 고려되고 있다. 기판으로는 스테인레스강이 가장 유력하며 Fe에 첨가된 Ni, Cr이 존재하므로 Cr 또는 CrN를 박막의 형태로 전자빔 증발법, 마그네트론 스퍼터링법으로 고속 증착하려는 시도가 있었다. 본 연구에서는, 스테인리스 강박(0.1 mm 이하)에 보호막으로 CrN을 선택하고 고속, 고품질증착을 위해서 새로운 방법인 스퍼터 승화법을 개발하였다. 박막의 품질을 개선할 수 있는 고밀도 유도 결합 플라즈마 영역 내에 Cr 소스를 직류 바이어스 함으로써 가열 및 스퍼터링이 일어나도록 하였다. 5 mTorr의 Ar 유도 결합 플라즈마를 2.4 MHz, 500 W로 유지하면서 직류 바이어스 전력을 30 W (900 V, 0.02 A) 인가하고, $N_2$의 유량을 0.5, 1.0, 1.5 SCCM로 변화를 주어 반응성 증착 공정의 결과로 얻어지는 CrN 박막의 특성을 분석하였다. N2의 유량이 증가할수록 $Cr_2N$이 감소하고, CrN이 증가하는 것을 확인하였다. 또한 부식성과 접촉저항을 측정하였다. 부식 전위는 N20 SCCM 보다 모두 상승하는 것을 확인하였고, $N_21$ SCCM에서 부식 전류 밀도가 2.097E-6 (at 0.6V) $A/cm^2$로 나타났다. 접촉저항 에서는 시료 당 3군데(top, center, bottom)를 측정하였다. 전기전도도 측면에서 가장 좋은 결과는 $N_21$ SCCM 일 때 $28.8m{\Omega}{\cdot}cm^2$의 접촉저항을 갖는 경우였다. 미국 에너지성의 기준은 부식 전류밀도 1.E-6 $A/cm^2$이하, 접촉 저항 $0.02{\Omega}m^2$이므로 매우 근접한 결과를 보이고 있다.

• Journal of the Korean institute of surface engineering
• /
• v.37 no.5
• /
• pp.296-300
• /
• 2004

The defects of partial denture frameworks are mainly shrinkage porosity, inclusions, micro-crack, particles from investment, and dendritic structure. In order to investigate a good casting condition of partial denture frameworks, the three casting alloys and casting methods were used and detected casting defects were analyzed by using electrochemical methods. Three casting alloys (63Co-27Cr-5.5Mo, 63Ni-16Cr, 63Co-30Cr-5Mo) were prepared for fabricating partial denture frameworks with various casting methods; centrifugal casting (Kerr, USA), high frequency induction casting (Jelenko Eagle, USA), vacuum pressure casting (Bego, Germany). The casting temperature was $1,380^{\circ}C$ (63Co-27Cr-5.5Mo and 63Ni-16Cr) and $1,420^{\circ}C$ (63Co-30Cr-5Mo). The casting morphologies were analyzed using FE-SEM and EDX. The corrosion test of the dendritic structure was performed through potentiodynamic method in 0.9% NaCl solutions at $36.5^{\circ}C$ and corrosion surface was observed using SEM. The defects of partial denture frameworks improved in the order of centrifugal casting, high frequency induction casting, and vacuum pressure casting method, especially, pore defects were found at part of clasp in the case of centrifugal casting method. The structure of casting showed dendritic structure for three casting alloys. In the 63Co-27Cr-5.5Mo and 63Co-30Cr-5Mo, $\alpha$-Co and $\varepsilon$-Co phases were identified at matrix and $${\gamma}$-Ni_2$Cr second phase were shown in 63Ni-16Cr. Also, the corrosion resistance of cast structure increased in the order of vacuum pressure casting, high frequency induction casting, and centrifugal casting method.

• Journal of the Mineralogical Society of Korea
• /
• v.21 no.1
• /
• pp.57-65
• /
• 2008

The geochemical partitioning of arsenic in contaminated soils from a of wet land and tailing of the abandoned mine is examined. Chemical analysis and sequential extraction method by ultrasound-sonication extraction are applied to investigate the mobility and chemical existence conditions of arsenic as well as heavy metals. The results of this study showed that heavy metals concentration of tailings showed as a following order: Fe > As > Cu > Pb > Cr. The highest metal concentration was recognized in samples less than $63\;{\mu}m$ fraction in their particle sizes. Exchangeable and carbonate fractions in soil samples showed following Cu > As > Pb > Fe > Cr for tailings, and Fe > Pb > Cu > As > Cr for reservoir soils, respectively. Arsenic was bound as exchangeable fraction in tailings and its concentration appeared higher than those of the other metals. Thus, As can be easily dispersed into soil and water environments. The obtained results can be used to design soil remediation plan in the study area and require further detailed study to investigate severe environmental pollution of surface water as well as rivers with respect to heavy metals in terms of speciation analysis of toxic elements such as As and Cr.

• Analytical Science and Technology
• /
• v.31 no.6
• /
• pp.240-246
• /
• 2018

The present study analyzed standard samples of three types of aluminum matrix certified reference materials (CRM) using GD-MS. Calibration curves were constructed for 13 elements (Mg, Si, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Ga, Sn, and Pb), with the slope representing the relative sensitivity factor (RSF). The x- and y-axes of the calibration curve represented ion beam ratio (IBR) and the authenticated value of the standard sample, respectively. In order to evaluate precision and linearity of the calibration curve, RSD and the coefficient of determination were calculated. Curve RSD for every element reflected high precision (within 10 %). For most elements, the coefficient of determination was ${\geq}0.99$, indicating excellent linearity. However, vanadium, nickel, and gallium curves exhibited relatively low linearity (0.90~0.95), likely due to their narrow concentration ranges. Standard RSF was calculated using the slope of the curve generated for three types of CRM. Despite vanadium, nickel, and gallium exhibiting low coefficients of determination, their standard RSF resembled that of the three types of CRM. Therefore, the RSF method may be used for element quantitation. Standard iron matrix samples were analyzed to verify the applicability of the aluminum matrix standard RSF, as well as to calculate the RSD-estimated error of the measured value relative to the actual standard value. Six elements (Al, Si, V, Cr, Mn, and Ni) exhibited an RSD of approximately 30 %, while the RSD of Cu was 77 %. In general, Cu isotopes are subject to interference: $^{63}Cu$ to $^{54}Fe^{2+}-^{36}Ar$ and $^{65}Cu$ to $^{56}Fe-Al^{3+}$ interference. Thus, the influence of these impurities may have contributed to the high RSD value observed for Cu. To reliably identify copper, the resolution should be set at ${\geq}8000$. However, high resolutions are inappropriate for analyzing trace elements, as it lowers ion permeability. In conclusion, quantitation of even relatively low amounts of six elements (Al, Si, V, Cr, Mn, and Ni) is possible using this method.

• Journal of Korean Society for Atmospheric Environment
• /
• v.26 no.2
• /
• pp.190-201
• /
• 2010

Fine particulate matter < $1.8{\mu}m$ was collected as a slurry using the Semicontinuous Elements in Aerosol Sampler with time resolution of 30-min between May 23 and 27, 2002 at the Sydney Supersite, Florida, USA. Concentrations of 11 elements, i.e., Al, As, Cd, Cr, Cu, Fe, Mn, Ni, Pb, Se, and Zn, in the collected slurry samples were determined off-line by simultaneous multi-element graphite furnace atomic absorption spectrometry. Temporal profiles of $SO_2$ and elemental concentrations combined with meteorological parameters such as wind direction and wind speed indicate that some transient events in their concentrations are highly correlated with the periods when the plume from an animal feed supplement processing facility influenced the Sydney sampling site. The peaking concentrations of the elemental species during the transient events varied clearly as the plume intensity varied, but the relative concentrations for As, Cr, Pb, and Zn with respect to Cd showed almost consistent values. During the transient events, metal concentrations increased by factors of >10~100 due to the influence of consistent plumes from an individual stationary source. Also the multi-variate air dispersion receptor model, which was previously developed by Park et al. (2005), was applied to ambient $SO_2$ and 8 elements (Al, As, Cd, Cr, Cu, Fe, Pb, and Zn) measurements between 20:00 May 23 and 09:30 May 24 when winds blew from between 70 and $85^{\circ}$, in which animal feed processing plant is situated, to determine emission and ambient source contributions rates of $SO_2$ and elements from one animal feed processing plant. Agreement between observed and predicted $SO_2$ concentrations was excellent (R of 0.99; and their ratio, $1.09{\pm}0.35$) when one emission source was used in the model. Average ratios of observed and predicted concentrations for As, Cd, Cr, Pb, and Zn varied from $0.83{\pm}0.26$ for Pb to $1.12{\pm}0.53$ for Cd.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.3 no.3
• /
• pp.103-111
• /
• 1998

This paper reports the sediment geochemistry and its relation to the grain size distribution in Kyeonggi Bay, Korea. Sediment samples were collected from 90 stations during the cruise crossing the bay in December 1995. Variables investigated were the sediment grain size, organic carbon content, and concentrations of AI, Fe, Mn, V, Co, Ni, Cr, Zn and Cu in the sediment. We followed the change in these variables by comparing the data obtained from this region in 1981. Distribution pattern of sediment grain size was modified from that in 1981 in some places. Near the Shihwa Dike which was completed in 1994, sediment had got finer grained. Sediment facies changed from fine to mixed facies near Youngjong Island where the tidal flat has been reclaimed for airport construction. Contents of organic matter and metals in the sediment were mostly dependent upon the sediment grain size, but an exception was found in the harbor area. The sediment in the Incheon North Harbor showed higher accumulation of organic matter and metals such as Ni, Cr, Zn and Cu.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.4
• /
• pp.145-151
• /
• 2005

Color enhancement of African rubies with dark red was carried out by the heat treatment and the hydrothermal treatment method respectively. The heat treatment method brought about an adverse effect causing the color to be deteriorated. However, the hydrothermal treatment method enhanced its color and clarity. The hydrothermal treatment conditions for color enhancement of them were as follows: solvent: 0.9M $Na_2CO_3-1M\;K_2CO_3$, temperature: $450^{\circ}C$, duration: 48 hrs, filling: $30\%$, pressure: 375 atm. As the results of characteristics for African rubies obtained under these conditions, it was known that the amount of $Cr^{3+},\;Fe^{3+},\;Ti^{4+}$ was reduced after the hydrothermal treatment from the ICP/MS and XRF analyses. Also, it was found that the red color from the colorimeter analyses was getting lighter. These results were consistent with the PL analysis showing that the intensity of the luminescence peak generated by the electron transition of $Cr^{3+}$ ion became lower after the hydrothermal treatment compared with the non-treated rubies.

• Journal of the Korean earth science society
• /
• v.23 no.1
• /
• pp.38-51
• /
• 2002

Mantle xenoliths in alkali basalt at Boun, the Gansung area and Baegryung Island in South Korea are spinel lherzolites composed of olivine, orthopyroxene, clinopyroxene, and spinel. Minerals show homogeneous compositions. Olivine compositions have Fo$_{89.0}$ to Fo$_{90.2}$, low CaO (0.03 to 0.12 wt%), and NiO of 0.34 to 0.40 wt%; the orthopyroxene is enstatite with En$_{89.0}$ to En$_{90.0}$ and Al$_{2}$O$_{3}$ of 4 to 5 wt%; the clinopyroxene is diopside with En$_{47.2}$ to En$_{49.1}$ and Al$_{2}$O$_{3}$ of 7.42 to 7.64 wt% from Boun and 4.70 to 4.91 wt% from Baegryung. Spinel chemistry shows a distinct negative trend, with increaeing Al corresponding with decreasing Cr, and Mg$^{#}$ (100Mg/Mg+Fe) and Cr$^{#}$ (100Cr/Cr+Al) of 75.1 to 81.9 and 8.5 to 12.6, respectively. The equilibrium temperatures of these xenoliths, taken as the average obtained from those of Mercier (1980) and Sachtleben and Seck (1981), lie between 970 and 1020$^{\circ}$C, and equilibrium pressures derived from Mercier (1980) fall within the range of 12 to 19 kbar (i.e., 42 to 63 km). These temperatures and pressures are reinforced by considerations of the Al-isopleths in the MAS system (Lane and Ganguly, 1980), as adjusted for the Fe effect on Al solubility in orthopyroxene (Lee and Ganguly, 1988). The equilibrium temperatures and pressures of xenoliths, as considered in P/T space, belong to the oceanic geotherm, based upon the various mantle geotherms presented by Mercier (1980). This geotherm is completely different from continental geotherms, e.g., from South Africa (Lesotho) and southern India. Mineral compositions of spinel-lherzolites in South Korea and eastern China are primitive; paleo-geotherms of both are quite similar, but degrees of depletion of the upper mantle could vary locally. This is demonstrated by eastern China, which has various depleted xenoliths caused by different degrees of partial melting.