• Transactions of Materials Processing
• /
• v.21 no.3
• /
• pp.207-214
• /
• 2012

High temperature deformation behavior of a $Ni_{30}Fe_{53}Co_{17}$ alloy, with its extraordinary low coefficient of thermal expansion less than $10{\times}10^{-6}K^{-1}$ at temperatures ranging from room temperature to 673K, was investigated by conducting a series of compression tests. From an empirical processing map, the appropriate working temperature-strain rate combination for optimum forming was deduced to be in the ~1373K, $10^{-2}s^{-1}$ region. This region has a relatively high power dissipation efficiency, greater than 0.36. Furthermore, open die forging of a 100mm diameter billets was performed to confirm the variation of thermo-physical properties in relation to microstructure. The coefficient of thermal expansion was found to increase considerably with increasing the open die forging temperature and decreasing the cooling rate, which in turn provides a drastic increase in the average grain size.

• Korean Journal of Crystallography
• /
• v.13 no.1
• /
• pp.36-40
• /
• 2002

The order-disorder phase transition of (Fe/sub 0.61/Ni/sub 0.39/)₃V alloy that is annealed at various temperatures and time conditions was sty(lied with the examination of long-range order parameter(S) by using neutron diffraction method. As a result, the structure of the sample annealed at 680℃ for 94 h was not changed; that is, it existed iii perfect disordered state and showed face-centered cubic structure. Otherwise, samples which were annealed at temperature below 640℃ showed the value of long-range order parameter with 0 < S < 1 and phase transition into simple cubic structure partly. It was found that the annealed sample at 465℃ for 144 h is the most approximated to the thermal equilibrium state from the S-T/T/sub c/ related equation of Cowley.

• Journal of the Korean Ceramic Society
• /
• v.36 no.5
• /
• pp.504-512
• /
• 1999

The high-quality carbon nanofibers were prepared by chemical vapor deposition of gas mixtures of CO-H2 and C3H8-H2 over Fe-Cu and Ni-Cu bimetallic catalysts. The yield and structure of carbon nanofiber produced were altered by the change of catalyst composition and reaction temperature. The high yields were obtained around 500$^{\circ}C$ with e-Cu catalyst and around 700-750$^{\circ}C$ with Ni-Cu catalyst and the relatively higher yields were obtained with the bimetallic catalyst containing 50-90% of Ni and Fe respectively in comparison with the pure metals. The carbon nanofibers produced over the Fe-Cu catalyst at around 500$^{\circ}C$ with the maximum yields had the highest surface ares of 160-200 m2/g around 650$^{\circ}C$ which was slightly lower than the temperature for maximum yields. In order to examine the characteristics of carbon nanofibers as catalyst support Ni and Co metals were supporte on the carbon nanofibers and CO hydrogenation reaction was performed with the catalysts. The particle size distribution of Ni and Co supported over the carbon nanofibers were 6-15 nm and the CO hydrogenation reaction rate with the carbon-nanofiber supported catalysts was much higher than that over the other supports.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.3
• /
• pp.128-136
• /
• 2023

In this study, the effects of heat treatment on the nano-scale creep behavior of CoCrFeMnNi high-entropy alloy (HEA) processed by high-pressure torsion (HPT) was investigated through nanoindentation technique. Nanoindentation experiments with a Berkovich indenter were performed on HPT-processed alloy subjected to heat treatment at 450℃, revealing that the hardness of the HPT-processed alloy (HPT sample) significantly increased with the heat treatment time. The heat treatment-induced microstructural change in HPT-processed alloy was analyzed using transmission electron microscopy, which showed the nano-sized Cr-, NiMn-, and FeCo-rich phases were formed in the HPT-processed alloy subjected to 10 hours of heat treatment (HPT+10A sample). To compare the creep behavior of HPT and HPT+10A samples, constant load nanoindentation creep experiments were performed using spherical indentation indenters with two different radii. It was revealed that the predominant mechanism for creep highly depended on the applied stress level. At low stress level, both HPT and HPT+10A samples were dominated by Coble creep. At high stress level, however, the mechanism transformed to dislocation creep for HPT sample, but continued to be Coble creep for HPT+10A sample, leading to higher creep resistance in the HPT+10A sample.

• Journal of the Korean Ceramic Society
• /
• v.42 no.4
• /
• pp.276-281
• /
• 2005

$LiNi_{1-y}M_{y}O_{2}(M=Zn^{2+},\;Al^{3+},\;and\;Ti^{4+},\;0.000\{\le}y{\le}0.100)$ were synthesized by the combustion method by calcining in $O_{2}$ stream at $750^{\circ}C$ for 36 h. XRD analyses, observation by FE-SEM and measurement of the variation of discharge capacity with the number of cycles were carried out. The composition $LiNi_{0.99}M_{0.01}O_{2}(M=Zn^{2+},\;Al^{3+},\;and\;Ti^{4+})$ of all the compositions showed relatively good electrochemical properties. $LiNi_{0.99}M_{0.01}O_{2}$ exhibited poor crystallinity and $LiNi_{0.99}M_{0.01}O_{2}$ showed the cation mixing of large fraction. $LiNi_{0.99}M_{0.01}O_{2}$ with improved cycling performance showed good crystallinity and the cation mixing of small fraction.

• Resources Recycling
• /
• v.4 no.3
• /
• pp.26-31
• /
• 1995

The leaching characteristics of manganese nodules were investigated in dilute hydrochloric acid solution using copper malie as a reductant. Thc capper matte has been found to be an effective reductant for exhacting morc than 96% of Mn, 95% of Ni, 91% of Ca, 88% of Cu and 36% of Fe when leached in 2.5 M HCI at 70$^{\circ}$C for 2hr. The dissolutions of Mu, Co, and Ni depend on thc amaunt of added cappcr matte. 7he ratin of liquid and solid is an important [actor on the extraction of metals during leaching The dissolution af Mn, Co, Ni and Cu incrcascd w~th the increase in temperalure of leachant. The leaching rates of Mn, Co, NI and Cu from manganese nodule m the presznce of copper matte is limited by bath thc surface chemical reaction and pare diffusion processes. Thc activation energies far Mn. Co: Ni and Cu were 17. 61, 12.8, 17.2 and 57.88 KcaUmol, rcspcctively.

• Journal of the Korean Ceramic Society
• /
• v.28 no.2
• /
• pp.146-152
• /
• 1991

Ultra fine and homogeneous (Ni0.4Zn0.6)Fe2O4 ferrite powders were prepared by direct-wet, Hydrothermal and coprecipitation methods. In case that specific surface areas of Ni-Zn ferrite powders were over 220㎡/g, 100㎡/g, 30㎡/g individually direct-wet, hydrothermal and coprecipitation methods. The Ni-Zn ferrite magnetic fluids of which Solvents were benzene or kerosene was prepared by making cation surfactant adsorbed on the surface of the (Ni0.4Zn0.6)Fe2O4. The results that measured dispersion and viscosity by making cation surfactant adsorbed were as follows. 1. The adsorption amount of Oleric acid be proportioned the specific surface area of powders. 2. The maximum amount of Oleric acid was 36wt% of dried powders which has 220㎡/g of specific surface area. 3. The stability of fluid by direct-wet synthesis emthod in benzene or kerosene solvent excellent.

• Korean Journal of Environmental Agriculture
• /
• v.5 no.1
• /
• pp.55-60
• /
• 1986

The objective of this study was to investigate the physical and chemical factors of Pinus densiflora SIEB. et ZUCC. and Quercus mongolica Fisher barks affecting on the adsorption of heavy metals. The results obtained can be summarized as follows: 1. With decreasing the particle size of bark, the adsorption rate of two heavy metal ions were increased. In case of using same particle size, the adsorption of $Fe^{++}$, and $Ni^{++}$ by Quercus bark showed higher than by Pinus bark. 2. The effect of untreated bark on the adsorption of heavy metal was more or less 5% higher than that of HCHO-treated bark in both species. But the color absorbances of the filtrates from HCHO-treated Pinus and Quercus barks were 5.8 and 11.8 times smaller than those of the filtrate from untreated Pinus and Quercus barks, respectively. 3. The maximum adsorption of $Fe^{++}$, and $Ni^{++}$ by bark was shown after 30 min. of the reaction. 4. With increasing the concentration of heavy metal, the amount of adsorption by bark was increased, but the adsorption ratio were decreased. 5. The maximum adsorption of $Fe^{++}$, and $Ni^{++}$ appeared at final pH of $4{\sim}5$, and pH of $3.6{\sim}4.0$ in filtrate, respectively. 6. With increasing the bark weight per a given heavy metal solution, the adsorption ratio were increased, but the amount of adsorption per gram of bark was the highest on the reaction with 2g of bark in a economical sense showing the amount of adsorption of 21mg $Fe^{++}$/g and 7mg $Ni^{++}$/g of Pinus bark, 36mg $Fe^{++}$/g and 9mg $Ni^{++}$/g of Quercus bark, respectively.

• Journal of Surface Science and Engineering
• /
• v.36 no.6
• /
• pp.444-454
• /
• 2003

The effect of trace metallic additives of Al-Fe-X on microstructure, glossiness and hardness of Zn electrodeposits was investigated by using sulfate bath. The preferred orientation of Zn deposits with Al-Fe additives was (10 l)(l:3,4,2), while that of Zn deposits with Al-Fe-X(Ni,Co) additives was either (002) or (002)＋(103)ㆍ(104) mixed orientation. The preferred orientation of Zn deposits with Al-Fe-Cr additives changed from (002)+(10 l) to (10 l) orientation with increasing amount of Al additive. The surface morphology of the Zn deposits was closely related to the preferred orientation of the deposits. The glossiness of Zn deposits with Al-Fe additives increased in comparison with that of pure Zn deposit. That of the Zn deposits with Al-Fe-X additives was related to the morphology of the deposits and changed according to type of additives. The hardness of Zn deposits with Al-Fe-X(Ni,Co,Cr) additives was noticeably higher than that of Zn deposits with Al-Fe additives.

• Transactions of Materials Processing
• /
• v.17 no.7
• /
• pp.507-510
• /
• 2008

Effect of V addition on the precipitation behavior and strength of Fe-36Ni based high strength Invar alloy for power transmission wire was investigated. Fe-36Ni Invar alloy plates were fabricated using conventional ingot casting followed by hot rolling. High strength can be obtained through precipitation hardening and strain hardening by cold rolling. Simulation using FactSage$^{(R)}$ revealed that equilibrium phases which can be formed are two kinds of MC-type precipitates, $Mo_{2}C$ and $M_{23}C_6$ carbide. The latter stoichiometric carbide was expected to be formed at relatively lower temperature of $800^{\circ}C$.