• Journal of the Korean Society of Food Science and Nutrition
• /
• v.28 no.5
• /
• pp.990-996
• /
• 1999

In physicochemical property, increasing the raw materials of Samul Chol Pyon, the content of moisture decreased, somewhat in total sugar, crude lipid, ash was increased. The pH of raw material for Samul Chol Pyon was shown at 5.70~5.80, in the mild acidity. Total saturated fatty acid of 50% added to the sample was shown to be four times higher than that of rice powder. The raw materials of Samul Chol Pyon were shown to possess 16 kinds of total amino acids. The content of minerals, K, P, Zn, Mn, Fe, Mg, Ca increased its additive raw material of Samul Chol Pyon. Especially, Na decreased, while K increased its additive raw materials of Samul Chol Pyon. In a limited Na diet, Samul Chol Pyon should be used in the future.

• Journal of the Korean Ceramic Society
• /
• v.29 no.3
• /
• pp.177-182
• /
• 1992

The effect of heat-treatment temperature on the microwave absorbing properties was investigated in Ni0.8Zn0.2Fe2O4 specimens. The composite specimens were prepared by modling and curing the mixture of prereacted ferrite powder and silicone rubber. The measurement of complex permeability and permittivity was made by the reflection/transmission method. The most sensitive material constants with heat-treatment temperature is the imaginary (loss) component of permeability. The higher the heat-treatment temperature, the greater the magnetic loss. The composite specimens with high magnetic loss exhibited superior microwave absorbing properties. The quantitative estimation of microwave absorbing properties were made by plotting the observed material constants on the calculated solution map of impedance-matching.

• Proceedings of the KIEE Conference
• /
• 1993.11a
• /
• pp.222-224
• /
• 1993

In this paper, The optimum oxidation conditions for the formation of Cu-Zn ferrite were investigated using precipitates obtained by the mixture of $CuCl_2{\cdot}2H_2O$, $ ZnCl_2$, $FeCl_3{\cdot}6H_2O$ and NaOH. The precipitates were prepared by coprecipitation method on various temperatures and oxidation conditions. The oxidation products were examined by SEM, XRD, and VSM. The particles obtained at 70($^{\circ}C$) were more spherical and fine than that of prepared at 25($^{\circ}C$), 50($^{\circ}C$), 60($^{\circ}C$), respectively. By $H_2O_2$ oxidation, the saturation magnetization of the powders was little influenced, But, by air oxidation the saturation magnetization of the powders was influenced intricately. According to our experimental data, the saturation magnetization of the powders increased with reaction time and was saturated at 9 hours.

• Fashion & Textile Research Journal
• /
• v.10 no.5
• /
• pp.779-783
• /
• 2008

The main colorant of Morus alba L. fruit is anthocyanin which is a kind of flavonoid group. In this article, the dyeing properties of colorant extracted from Morus alba L. fruit were investigated on some silk fabrics. The results were as follows: The maximum absorbance of Morus alba L. fruit showed at 284 nm, and 516 nm by UV-VIS spectrophotometer. The dye adsorption increased according as dye concentration. The optimal dyeing temperature was $60^{\circ}C$ and the dye equilibrium was reached 40 minutes after dyeing. The highest K/S value of the colorant obtained at bath ratio 40:1. The effect of pH of dye solution showed higher K/S value at acidic than alkaline condition. Almost Mordants except pre-Fe and Sn did not significantly increased dye adsorption. The pre mordanted silk fabrics showed RP, P, and post mordanted ones showed PB, GY. The color fastnesses to light, washing, and perspiration were modified at pre-Sn mordanted samples.

• Transactions of Materials Processing
• /
• v.17 no.5
• /
• pp.356-363
• /
• 2008

An evaluation system of the thermal properties of exothermic & insulating materials was developed. By measuring the power supply of the induction furnace, the thermal property of exothermic & insulating materials could be evaluated with high reproducibility at elevated temperature of molten steel. The thermal properties of exothermic & insulating materials were affected by mixing condition of raw materials. The effect of main components of exothermic & insulating materials such as metallic aluminum and $Fe_2O_3$ powder on the exothermic and insulating properties was examined. It could be expected to design and develop various exothermic & insulating materials by means of the evaluation system of the thermal properties.

• Resources Recycling
• /
• v.13 no.1
• /
• pp.54-58
• /
• 2004

Wollastonite-type glass ceramics were prepared by milling and firing at various temperatures using an automobile waste glass and waste shell as starting materials. Powder mixture ground by disk-type ball mill for 3 hours was pressed into a disk. The pressed specimen was fired at $850^{\circ}C$,$950^{\circ}C$ and $1050^{\circ}C$ for 1 hour in air. From FE-SEM observation, with an increase of the firing temperature from $850^{\circ}C$ to $1050^{\circ}C$, whisker-type phase was grown to about 10 $\mu\textrm{m}$ in length. Specimen fired at $1050^{\circ}C$ showed the formation of well-crystallized whisker-type wollastonite grains and the highest compressive strength.

• Journal of Sensor Science and Technology
• /
• v.16 no.5
• /
• pp.355-360
• /
• 2007

Highly sensitive thick film ethanol gas sensors based on a nanocrystalline $In_{2}O_{3}$ were fabricated by painting method on alumina substrates. The crystal structure of the $In_{2}O_{3}$ powder was characterised by XRD analysis. The microstructure of the films were characterised using FE-SEM. The experimental results of the ethanol gas sensing characteristics indicated that the undoped $In_{2}O_{3}$ thick film has a high sensitivity. The sensitivity of the film heat treated at $400^{\circ}C$ for 2 hrs. was as high as 32.73 at an operating temperature of $200^{\circ}C$ to 1000 ppm ethanol gas in air.

• Journal of Korean Society on Water Environment
• /
• v.31 no.6
• /
• pp.632-636
• /
• 2015

This study aims to evaluate arsenic adsorption efficiencies over various metal oxides (CeO₂, TiO₂, Fe₃O₄, ZrO₂, AlOOH, SiO₂, α-Al₂O₃, and γ-Al₂O₃) and investigate the correlation between physico-chemical characteristics of metal oxides and their efficiencies. From XPS, XRD BET analysis and isotherm adsorption test, TiO₂ powder showed that the best adsorption efficiency, and it's mechanism was highly depended on the chemical adsorption.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.08a
• /
• pp.27-30
• /
• 2003

In order to get the infrared ray radiator with high efficiency emission, the starting raw material $Fe_2O_3$ powder is heat-treated under the oxygen pressure log[$PO_2$] = -13~15 at $800^{\circ}C$ for 2hours. It has shown that the radiation rate was larger than 0.85 at the relatively high temperature($400^{\circ}C$), and decreased slowly with increasing the temperature from 50 to $400^{\circ}C$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.05a
• /
• pp.109-110
• /
• 2006

Nanocrystalline $TiO_2$ electrode were prepared by spray-printing in order to efficiency and improved fill factor. Different compositions of nanocrystalline $TiO_2$ pastes are described, based on $TiO_2$ powder made by ourselves. The produced by spray printing $TiO_2$ films were compare with the produced by squeeze printing $TiO_2$ films and was studied in the light of static I-V characteristics. The produced $TiO_2$ films are extensively characterized by means of spectroscopy(Ramon, XRD) and microscopy(FE-SEM).