• Journal of the Korean Chemical Society
• /
• v.32 no.1
• /
• pp.3-8
• /
• 1988

Nonstoichiometric solid solutions of the $Sr_{1+x}Dy_{1-x}FeO_{4-y}$ system (x = 0. 00, 0. 25, 0. 50, 0. 75 and 1. 00) with layered $K-2NiF_4$ type structure were prepared at 1200$^{\circ}$C under atmospheric pressure. X-ray powder diffraction spectra show that the crystallographic phases of the samples are tetragonal within the x range. Nonstoichiometric chemical formulas have been determined by Mohr salt analysis and it shows that the amount of $Fe^{4+}$ ion or ${\tau}$ value increases with increasing x. Electrical conductivities of the samples which were measured in the temperature range of $-100{\sim}200^{\circ}$C under atmospheric air pressure are varied within the semiconductivity range of $l0^{-8}{\sim}10^{-2}(ohm^{-1}{\cdot}cm^{-1}$) and the activation energies are also varied from 0.02 to 0.08 eV. Mixed valency state of $Fe^{3+}$ and $Fe^{4+}$ in the sample of $Sr_{1.00}Dy_{1.00}FeO_{4.04}$ was identified again by Mossbauer spectrum at 200K.

• Applied Chemistry for Engineering
• /
• v.7 no.3
• /
• pp.543-553
• /
• 1996

Oxygen reduction in an alkaline fuel cell was studied by using perovskite type oxides as an oxygen electrode catalyst. The high surface area catalysts were prepared by malic acid method and had a formula of $La_{0.6}Sr_{0.4}Co_{1-x}Fe_xO_3$(x=0.00, 0.01, 0.10, 0.20, 0.35 and 0.50). From the result of XRD pattern and specific surface area due to the amount of Fe substitution and the consumption of ammonia-water, the complex formation of Fe ion with $NH_3$ was the main factor for both the phase stability of perovskite and the increase of specific surface area. Multi-step calcination was necessary to give a single phase of perovskite in catalyst precursor. The crystal structure of the catalysts was simple cubic perovskite, which was verified from the XRD patterns of the catalysts. The activity of oxygen reduction was monitored by the techniques of cyclic voltammetry, static voltage-current method, and current interruption method. The activity(current density) of oxygen reduction showed its minimum at x=0.01 and its maximum between 0.20 and 0.35 of x-value in $La_{0.6}Sr_{0.4}Co_{1-x}Fe_xO_3$. This tendency was independent of the change of surface area.

• Transactions of the Korean hydrogen and new energy society
• /
• v.13 no.2
• /
• pp.143-150
• /
• 2002

The thermal behavior of $(Co_{0.5}\;Mn_{0.5})Fe_2O_4$ prepared by a co-precipitation wasinvestigated for Hz generation by the thermochemical cycle. The reduction reaction of $(Co_{0.5}\;Mn_{0.5})Fe_2O_4$ started from $480^{\circ}C$, and the weight loss was 1.6 wt% up to $1100^{\circ}C$. At this reaction, $(Co_{0.5}\;Mn_{0.5})Fe_2O_4$ was reduced by release of oxygen bonded with the $Fe^{3+}$ ion in the B site of ($CO_{0.5}$ $(Co_{0.5}\;Mn_{0.5})Fe_2O_4$. In the $H_2O$ decomposition reaction, $H_2$ was generated by oxidationof reduced $(Co_{0.5}\;Mn_{0.5})Fe_2O_4$. The crystal structure of $(Co_{0.5}\;Mn_{0.5})Fe_2O_4$ for reduction reaction maintained spinel structure and the lattice constant of $(Co_{0.5}\;Mn_{0.5})Fe_2O_4$ ($8.41\AA$) was enlarged to $8.45\AA$. But the lattice constant of $(Co_{0.5}\;Mn_{0.5})Fe_2O_4$ after $H_2O$ decomposition reaction did not change to $8.45\AA$. Then, $(Co_{0.5}\;Mn_{0.5})Fe_2O_4$ is excellent material in the thermochemical cyclic reaction due to release oxygen at low temperature for the reduction reaction and produce $H_2$ maintaining crystal structure for redox reaction.

• Resources Recycling
• /
• v.16 no.6
• /
• pp.3-9
• /
• 2007

Although the ferrous material was separated by the magnetic separation before the incineration process, the municipal solid waste incineration bottom ash generated during incinerator in metropolitan area consists of many iron products which account for about $3{\sim}11%$ as well as ceramics and glasses. The formation of $NiFe_2O_4$ and $FeCr_2O_4$ with a $Fe_3O_4-Fe_2O_3$ (similar to pure Fe) on the surface of iron product was found during air-annealing in the incinerator at $1000^{\circ}C$, because Ni and Cr has a chemical attraction about iron is using to coat with Ni and Cr metals for poish or to prevent corrosion. Therefore, Fe-Ni Cr oxide can be formed on durface of the iron product and it can be separated from bottom ash through the magnetic separation. So, in this study, the separation ratio of heavy metals as magnetic separation and mineralogical formation of Fe-ion(heavy metal) in ferrous metals corroded were investigated. As the result, the separation ratio of Ni and Cr based on particle sizes accounted for about $45{\sim}50%$, and Cu and Pb accounted for below 20%. Also, the leaching concentration of Ni and Cr in bottom ash separated by magnetic separation was lower than that in fresh bottom ash.

• Journal of the Korean Chemical Society
• /
• v.53 no.3
• /
• pp.368-376
• /
• 2009

In this study we investigated and tried to understand problems monitored in an experiment on reactivity of metals in chemistry I. Three problems were discussed. First, the reason that aluminium plate does not react with other metal ions such as zinc, iron and copper was studied and the way to overcome this problem was suggested. Second, the reason that the bubbles were generated when FeS$O_4$(aq) and Zn(s) react was discussed. Third, the precipitates which appeared in the reaction of FeS$O_4$(aq) and Zn(s) were identified. Through reference study and experimental investigation, we could reach the following results. First, aluminium could not react with other metal ions due to the surface oxide layer that is formed very fast and prevents aluminium from reacting with metal ions in solution. This problem could be overcome by allowing a competing reaction of acid and aluminium during the reaction of aluminium and metal ions. Second, the observed bubbles were identified to be hydrogen gas, produced by the reaction between metals and hydronium ion in the solution. Third, black precipitates that were produced on the surface of zinc plate and exhibited magnetic property were characterized to be $Fe_3O_4$(s), and brown precipitates that were produced in the solution phase were to be $Fe_2O_3$(s) by the analysis of X-ray photoelectron spectra.

• Analytical Science and Technology
• /
• v.31 no.6
• /
• pp.240-246
• /
• 2018

The present study analyzed standard samples of three types of aluminum matrix certified reference materials (CRM) using GD-MS. Calibration curves were constructed for 13 elements (Mg, Si, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, Ga, Sn, and Pb), with the slope representing the relative sensitivity factor (RSF). The x- and y-axes of the calibration curve represented ion beam ratio (IBR) and the authenticated value of the standard sample, respectively. In order to evaluate precision and linearity of the calibration curve, RSD and the coefficient of determination were calculated. Curve RSD for every element reflected high precision (within 10 %). For most elements, the coefficient of determination was ${\geq}0.99$, indicating excellent linearity. However, vanadium, nickel, and gallium curves exhibited relatively low linearity (0.90~0.95), likely due to their narrow concentration ranges. Standard RSF was calculated using the slope of the curve generated for three types of CRM. Despite vanadium, nickel, and gallium exhibiting low coefficients of determination, their standard RSF resembled that of the three types of CRM. Therefore, the RSF method may be used for element quantitation. Standard iron matrix samples were analyzed to verify the applicability of the aluminum matrix standard RSF, as well as to calculate the RSD-estimated error of the measured value relative to the actual standard value. Six elements (Al, Si, V, Cr, Mn, and Ni) exhibited an RSD of approximately 30 %, while the RSD of Cu was 77 %. In general, Cu isotopes are subject to interference: $^{63}Cu$ to $^{54}Fe^{2+}-^{36}Ar$ and $^{65}Cu$ to $^{56}Fe-Al^{3+}$ interference. Thus, the influence of these impurities may have contributed to the high RSD value observed for Cu. To reliably identify copper, the resolution should be set at ${\geq}8000$. However, high resolutions are inappropriate for analyzing trace elements, as it lowers ion permeability. In conclusion, quantitation of even relatively low amounts of six elements (Al, Si, V, Cr, Mn, and Ni) is possible using this method.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.142-142
• /
• 2009

Bismuth-substituted yttrium iron garnet(Bi-YIG; $Bi_xY_{3-x}Fe_5O_{12}$, x=0, 0.5, 1.0, 1.5, 2.0) thin films were fabricated on glass substrates using a metal organic decomposition (MOD) method. The dielectric property was measured by NSMM(Near-field scanning microwave microscopy) system that operating frequency is 4 Ghz. The obtained reflection coefficient $S_{11}$ of the Bi:YIG thin films with different bismuth concentration was increased as the bismuth concentration increased due to the lattice mismatch and vacancy of ions because of a lager ionic radius of bismuth ion than yttrium ion.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.10
• /
• pp.1683-1688
• /
• 2007

This paper presents a novel simple method for introducing gold nanoparticles in a poly(4-vinylpyridine) (PVP) polymer layer over a glassy carbon (GC) electrode with the aim of forming a tunable electrochemical interface against a cationic ruthenium complex. Initially, AuCl4 ? ions were spontaneously incorporated into a polymer layer containing positively charged pyridine rings in an acidic media by ion exchange. A negative potential was then applied to electrochemically reduce the incorporated AuCl4 ? ions to gold nanoparticles, which was confirmed by the FE-SEM images. The PVP layer with an appropriate thickness over the electrode blocked electron transfer between the electrode and the solution phase for the redox reactions of the cationic Ru(NH3)6 2+ ions. However, the introduction of gold nanoparticles into the polymer layer recovered the electron transfer. In addition, the electron transfer rate between the two phases could be tuned by controlling the number density of gold nanoparticles.

• Microbiology and Biotechnology Letters
• /
• v.24 no.3
• /
• pp.364-370
• /
• 1996

Sediments collected from the Jungnang-cheon and its tributaries were used to enumerate anaerobic bacteria by most probable number (MPN) methods. A simple method was developed to detect ferrous ion in the culture fluid in order to count the number of iron ion reducers, and sulfate-reducing bacteria (SRB) and methanogens were detected by the presence of FeS precipitate in the culture or methane in the head space, respectively. The numbers of iron reducer was in the range of 10$^{7}$ - 10$^{8}$ /g in the sediment of the stream containing higher organic content than the tributaries. The sediments of tributaries were analyzed to contain iron reducers less than 10$^{7}$ cells/g. With one exception the numbers of SRB and methanogens were less than 10$^{3}$ cells/g in the sediment. From these results it is concluded that organics in the sediment support the growth of iron reducers, which out-compete SRB and methanogens.

• Textile Coloration and Finishing
• /
• v.13 no.5
• /
• pp.10-10
• /
• 2001

The Purpose of this study was to investigate spectrophotometric characteristics of Korean knotweed extracts. The properties were evaluated by it′s extracting solvent, effect of metallic ion, variations of pH values and effect of light exposure. The results were as following; The highest absorbance was found in methanol extract of Korean knotweed, while the lowest absorbance was carbon tetrachloride extract. The UV-vis. spectra of Korean knotweed colors in several solvents showed hypsochromic shift of n-π/sup ＊/ transition with the polarity of solvent. Absorbance and peak of UV-vis. spectra of Korean knotweed colors became lower and broader by addition of metallic ion. The light stability in irradiation with xenon ]amp of the color solution with Cu were higher than those of Al and Fe. The UV-vis. spectra of Korean knotweed extracts in various pH values showed bathochromic shift under alkaline condition, and their peaks disappeared after 5 hours exposure.