• Journal of the Korean Magnetics Society
• /
• v.1 no.2
• /
• pp.9-14
• /
• 1991

In order to investigate electronic and magnetic properties of $Fe_{16}N_{2}$ ferromagnet, we have performed electronic structure calculations employing the self-consistent local density functional LMTO(linearized muffin tin orbital) band method. We have obtained the ground state parameters, such as band structures, density of states, Stoner parameters, and magnetic moments. Based on these results, we have investigated microscopically the magnetic structure and the enhancement of Fe magnetic moments in this compound. Magnetic moments of 3 types of Fe(Fe I, Fe II and Fe III) in $Fe_{16}N_{2}$ are 2.13, 2.50, and $2.85\;{\mu}_{B}$, respectively. Large enhancement of Fe magnetic moment is observed in Fe II and Fe III, which are located rather far from N. This implies that local environment is very important in determining the Fe magnetic moments in this compound. Our value of average magnetic moment per Fe atom. $2.50\;{\mu}_{B}$, is a bit smaller than the reported estimate, $-3.0\;{\mu}_{B}$, from the experiment.

• Korean Journal of Materials Research
• /
• v.8 no.8
• /
• pp.720-725
• /
• 1998

As a basic study on the production of $Sm_{2}Fe_{17}N_{x}$ system rare earth permanent magnet by the reduction and diffusion(R- D) process, firstly the reduction reaction of $Sm_2O_3$ by metallic Ca and diffusion of Sm into Fe powder was investigated for the production the $Sm_{2}Fe_{17}$intermetallic compound. We concluded that the former case was very rapidly completed under the high temperature greater than 100$0^{\circ}C$ and the latter case of completion of diffusion reaction of Sm into the center of Fe powder(perfect homogenization condition) was required through 3h R- D reaction at 110$0^{\circ}C$ and identified as a rate determining step(RDS) on the whole reaction. Though $SmFe_2,SmFe_3$, and $Sm_{2}Fe_{17}$phases in the growth of phases of intermetallic compound in the Sm - Fe binary system were obseved below 100$0^{\circ}C$, but only $Sm_{2}Fe_{17}$phase was observed at lIOO$^{\circ}C$. Oxygen and Ca contents of the final sample in this work were 0.72wt% and O. 11 wt% respectively.

• Journal of Korean Society for Atmospheric Environment
• /
• v.3 no.2
• /
• pp.18-26
• /
• 1987

In order to investigate the character of air pollution by heavy metals and to elucidate the possible sources in Seoul city, this study was performed to measure the concentrations of heavy metals of total suspended particulate and air pollutants such as $SO_2, NO_2, CO, CH_4$, Non-methane hydrocarbon, ozone at the residential-traffic area (shinchon dong) in January and February, 1986. The results are as follows: 1. $SO_2$ and TSP concentration were 135ppb and 167 $\mug/m^3$ in average, respectively. 2. While concentrations of heavy metals such as Fe, Cu, Pb in the ambient air seems gradually decreasing annually, Ni compound has been shown the tendency of increasing. 3. Among heavy metals in TSP analysed, the iron was detected at the highest level, 0.905% and the cadimium was the lowest 0.004% in average, respectively. 4. V, Fe and Zn compounds in air were observed to be highly correlated with their correlation coefficients(r) higher than 0.7. Pb compound was highly correlated to the levels of Zn and Fe, however relatively less correlated to V compound. 5. Among concentrations of heavy metals in the particulates, V and Ni compounds were highly correlated with coefficient(r) of 0.8587; the cause might be imagined by the fact of releasing from combustion of fuel oil. Fe, Pb and Zn compounds were highly correlated $SO_2$ concentration. It might be explained that they were released by combustion of coal. 6. The level of $SO_2$ was highly correlated to most of heavy metals: especially correlation coefficient(r) to Pb compound was 0.9081. Pb compound was also highly correlated to NO, CO and TSP. TSP showed higher correlation to Pb and Cd compounds than to V and Ni compounds. It might be assumed that particulate was mainly produced by combusting coal from space heating and by exhausting gasoline and diesel oil from transportation rather than by burning fuel oil.

• Analytical Science and Technology
• /
• v.22 no.3
• /
• pp.254-262
• /
• 2009

Activated carbon fiber treated with iron compound (Fe-ACF) was employed for preparation of Feactivated carbon fiber/$TiO_2$ (Fe-ACF/$TiO_2$) composite catalysts. Then, the prepared Fe-ACF/$TiO_2$ composite catalysts were characterized by employing BET, SEM, XRD and EDX instruments. It showed that BET surface area was related to adsorption capacity for each composite. The SEM results showed that ferric compound and titanium dioxide were distributed on the surfaces of ACF. The XRD results showed that Fe-ACF/$TiO_2$ composite mostly contained an anatase structure with a Fe mediated compound. EDX results showed the presence of C, O, and Ti with Fe peaks in Fe-ACF/$TiO_2$ composites. From photocataytic degradation effect, it was observed in the organic dye (Methylene blue, MB) degradation by these composites. Different degradation effect can be attributed to the synergetic effects of photo-Fenton reaction of Fe. It was considered that the combined reactions of Fe-ACF/$TiO_2$ produce powerful photo-Fenton process in the MB degradation.

• Journal of the Korean Society for Heat Treatment
• /
• v.2 no.4
• /
• pp.27-39
• /
• 1989

The effect of gas mixing ratios during gas nitrocarburizing treatment on the formation of compound layer and the mechanical properties has been studied for hot work tool steel by using a combined heat treating technique. The thickness of compound and diffusion layers has been shown to grow as a parabolic relation with increasing the amount of ammonia at a given flow quantity of $CO_2$ gas. The compound layer consists mainly of ${\varepsilon}-Fe_3$(C, N) with small amounts of ${\gamma}^{\prime}-Fe_4N$ and ${\alpha}$-Fe. The combined heat treated hot work tool steel has shown that the thickness of compound layer increases with increasing nitrocarburizing time, but the rate of growth slows down as gas nitrocarburizing time goes more than two hours. Tensile properties have given a remarkable improvement. In particular, the wear resistance of combined heat treated hot work tool steel has exhibited an improvement of about 165% greater than that obtained from conventional quenching and multi-tempering treatments.

• Journal of Powder Materials
• /
• v.11 no.2
• /
• pp.105-110
• /
• 2004

In this study the possibility to obtain a homogeneous mixture and to produce solid solutions and intermetallic compounds of Fe and Al nano particles by simultaneous pulsed wire evaporation (S-PWE) have been investigated. The Fe and Al wires with 0.45 mm in diameter and 35 mm in length were continuously co-fed by a special mechanism to the explosion chamber and simultaneously exploded. The characteristics, e.g., phase composition, particle shape, and specific surface area of Fe-Al nano powders have been analyzed. The synthesized powders, beside for Al and $\alpha$-Fe, contain significant amount of a high-temperature phase of $\gamma$-Fe, Fe Al and traces of other intermetallics. The phase composition of powders could be changed over broad limits by varying initial explosion conditions, e.g. wire distance, input energy, for parallel wires of different metals. The yield of the nano powder is as large as 40 wt ％ and the powder may include up to 46 wt % FeAl as an intermetallic compound.

• Journal of the Korean Society for Heat Treatment
• /
• v.16 no.2
• /
• pp.71-77
• /
• 2003

We investigate the phase formation in the compound layer of cast irons during the gaseous nitrocarburising of four different cast irons, that contain different types of graphites in the shape and size. We examine the change in the surface roughness with the nitrocarburising time. The observation of cross-sectional microstructure and X-ray diffraction analysis indicate that the compound layer consists of single ${\varepsilon}-Fe_{2-3}(N,C)$ phase and that its thickness increases in a parabolic manner with the treatment time. The surface roughness parameters, Rz and Ra increase with increasing treatment time. In other words, the roughness parameters increase as the thickness of compound layer increases. The parameters also depend on the shape and size of graphite in the individual cast irons.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.5
• /
• pp.443-448
• /
• 1996

In order to plasma-sulfnitride by combining ion-nitriding of a steel and sputtering of MoS$_2$, chromium-molybdenum steel was plasma-sulfritrided using hollow cathode discharge with parallel electrodes which are a main of the steel and a subsidiary cathode of $MoS_2$. The treatment was carried out at 823K for 10.8ks under 665Pa in a 30% $N_2$-70% $H_2$ gas atmosphere. Plasma-sulfnitriding layers formed of the steel were characterized with EDX, XRD, micrographic structure observation and hardness measurement. A compound layer of 8-15$\mu\textrm{m}$ and nitrogen diffusion layer of about 400$\mu\textrm{m}$ were formed on the surface of plasma-sulfnitrided steel. The compound layer consisted of FeS containing Mo and iron nitrides. The nitrides of $\varepsilon$-$Fe_2_3N$ and $\gamma$'-$Fe_4N$ formed under the FeS. The thickness of compound layer and surface hardness were different with the gaps between main and subsidiary cathodes even in the same sulfnitriding temperature. The surface hardnesses after plasma-sulfnitriding were distributed from 640 to 830Hv. The surface hardness was higher in the plasma-sulfnitriding than the usual sulfnitriding in molten salt. This may be due to Mo in sulfnitriding layer.

• Journal of Ginseng Research
• /
• v.23 no.2 s.54
• /
• pp.61-66
• /
• 1999

Experiments were carried out to examine the rusty tolerance in 61 inbred lines of ginseng cultivated in field, and chemical components were analyzed to clarify the difference between healthy and rusty ginseng roots. Among them, 10 lines showed rusty tolerance (RT) while 10 lines showed rusty sensitivity (RS). The content of phenolic compound in RT was lower than that in RS in cortex, epidermis and branch & fine roots, but it was not difference between RT and RS in stele. The contents of K, Ca, Na in RT were lower than RS in cortex, and the content of Mg, Fe, Na, Mn, AI, Si in RT were lower than RS in epidermis, and the content of Fe in RT were lower than RS in branch & fine roots, but mineral contents were not difference between RT and RS in stele. The content of phenolic compound in healthy cortex was lower than that in rusty cortex in same 6-year roots, but the mineral contents were not difference between healthy and rusty cortex in same 6-year roots. In root of seedlings, the contents of phenolic compound, K and Na in RT were lower than RS. It was suggested that the contents of phenolic compound, K and Na might be marker to select rusty tolerance ginseng lines.

• Proceedings of the Korea Society of Environmental Biology Conference
• /
• 2002.05a
• /
• pp.46-46
• /
• 2002